Fetco L3D-20 User manual

Brand: Fetco

Model: L3D-20

Category: Coffee making accessories

Type: User manual

Fetco Home Decor L3D-20 is a thermal dispenser with a capacity of 2 gallons. It is ideal for keeping beverages hot and fresh for hours, making it perfect for use in homes, offices, and other settings where hot beverages are frequently served. The L3D-20 features a sleek and modern design that will complement any décor, and its durable construction ensures years of reliable use.

Some of the key features of the L3D-20 include:

Precise temperature control: The L3D-20 maintains a consistent temperature to keep your beverages hot and fresh for hours.
Easy to use: The L3D-20 is simple to operate, with just a few buttons to control all of its functions.

Some of the key features of the L3D-20 include:

Precise temperature control: The L3D-20 maintains a consistent temperature to keep your beverages hot and fresh for hours.
Easy to use: The L3D-20 is simple to operate, with just a few buttons to control all of its functions.

www.fetco.com

FETCO® and LUXUS® are trademarks or trade names of

Food Equipment Technologies Company. Part # P015 Rev. June 2, 2003

L3D-10

1 gallon

L3D-15

1.5 gallon

L3D-20

2 gallon

User’s Guide

L3D Series

Thermal Dispensers

IMPORTANT SAFEGUARDS

 To prevent overflows, make sure the dispenser is completely

empty before brewing.

 Always remove the funnel for manual filling of the dispenser.

 Do not use bleach or cleaners containing chlorides.

 Use only non-metallic brushes and cleaning pads.

 Use only the handle to lift or carry the dispenser.

 Do not use the faucet guard to pull or lift the dispenser.

 Do not submerge the brew funnel.

CLEANING AND MAINTENANCE

Daily:

Important Notice: To maintain proper operation of the funnel

display, clean the funnel stem daily under running water with

detergent and a sponge or towel. Do not submerge.

 Use any commercial beverage urn cleaner to clean the inside of

the dispenser. Follow the cleaner manufacturer’s instructions.

Make sure to thoroughly rinse the dispenser after cleaning.

 Wash the drip tray and other plastic parts with dish detergent.

Avoid abrasives.

 To sanitize the dispenser before filling, brew a batch of water only

(no coffee) into the dispenser and allow it to rest for 10 minutes.

Weekly, or as needed:

 Remove the faucet upper assembly and inspect the seat cup for

wear. Clean or replace if necessary.

BREW FUNNEL DISPLAY

(Display updates every 6 seconds.)

Freshness Timer Volume Display

Timer is reset when dispenser is

completely emptied, when funnel is

removed, or when enough liquid is

added to increase the volume by at

least one level.

Examples for L3D-15:

Troubleshooting:

= 15 minutes.

= 1 hour.

- Each bar equals

gallon.

- “V” section is 1

bar.

- Example shown is L3D-15.

L3D-10 has 4 bars.

L3D-15 has 6 bars.

L3D-20 has 8 bars.

15 minutes

Full

1 hour, 45 minutes

Half full –

gallon

3 hours, 30 minutes

gallon

Problem: “V” segment of volume display is

flashing slowly.

Cause: Funnel stem is dirty.

Solution: Clean funnel stem with detergent

and a s

e or towel.

Problem: Every other bar of volume display

is flashing slowly.

Cause: Battery power is low or internal

malfunction.

Solution: Replace with new funnel.

Battery cannot be replaced.

- flashing -

= Maximum time has

elapsed. (4 hrs.)

- flashing -

Closed

position

for serving

Open

position

for brewing

OPENING THE

DISPENSER

OPENING AND CLOSING

THE COVER PLUG

Squeeze tabs

together and lift.

REMOVING THE BREW FUNNEL

REMOVING THE DRIP TRAY

Press and hold down latch release

while sliding drip tray out.

latch

release

Important Notice: To

maintain proper operation

of the funnel display, clean

the funnel stem daily under

running water with

detergent and a sponge or

towel. Do not submerge.

 Brew funnel must be removed

for manual filling of dispenser.

 Removing the funnel resets

the timer.

 To extend battery life, remove

the funnel when not in use.

(Battery cannot be replaced.)

REMOVING THE FAUCET GUARD

REMOVING THE FAUCET

Press faucet

release latch up.

Unscrew knob 4 turns and

slide faucet guard out.

knob

Unscrew faucet upper

assembly to clean or

replace seat cup.

Reverse procedure to re-

install faucet. Press release

latch down to lock faucet in

place.

Rotate faucet 180°

and pull it out.

www.fetco.com

Replacement Parts

L3D-10 L3D-15 L3D-20

Part #

Part # Part #

funnel assembly, with gasket K001 K002 K003

funnel gasket 24053 24056 24056

faucet guard 23166 23137 23137

faucet guard knob, w/washer K010 K010 K010

faucet assembly, complete K011 K011 K011

faucet upper assembly

(black handle, seat cup, spring assy.)

71037 71037 71037

faucet handle, black 71028 71028 71028

faucet handle, orange 71027 71027 71027

faucet handle, red 71080 71080 71080

faucet handle, green 71085 71085 71085

faucet seat cup 71035 71035 71035

drip tray assembly

(tray & cover)

K013 K014 K014

640 Heathrow Drive, Lincolnshire, IL 60069 USA

Phone: (847) 719-3000 Fax: (847) 821-1178

e-mail: [email protected]

Fetco L3D-20 User manual

Brand: Fetco

Model: L3D-20

Category: Coffee making accessories

Type: User manual

Some of the key features of the L3D-20 include:

Precise temperature control: The L3D-20 maintains a consistent temperature to keep your beverages hot and fresh for hours.
Easy to use: The L3D-20 is simple to operate, with just a few buttons to control all of its functions.

Download PDF

report

Fetco L3D-20 User manual

Fetco L3D-20 User manual

Related papers

Other documents