Planet GRT-401 User manual

PLANET Technology Corp. GRT-101/401/402 User’s Manual

G.SHDSL Bridge/Router

GRT-101/GRT-401/GRT-402

User’s Manual

- -

1

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Copyright

The products and programs described in this User’s Manual are licensed products of PLANET

Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s

the

rchaser's personal use, and without the prior express written permission of PLANET Technology.

r expressed, with respect to the

anual is accurate; PLANET disclaims liability

to this User’s Manual

ual that is incorrect, misleading, or incomplete, we would appreciate

ur comments and suggestions.

uct may cause radio interference, in which

se the user may be required to take adequate measures.

these designations are

aimed as trademarks or registered trademarks by their respective companies.

:

-401/ GRT-402 (GRT series)

Part No. EM-GRTV4

Manual and all accompanying hardware, software, and documentation are copyrighted.

No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any

electronic medium or machine-readable form by any means by electronic or mechanical. Including

photocopying, recording, or information storage and retrieval systems, for any purpose other than

pu

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and

applications, and makes no warranty and representation, either implied o

quality, performance, merchantability, or fitness for a particular purpose.

PLANET has made every effort to ensure that this User’s M

for any inaccuracies or omissions that may have occurred.

Information in this User’s Manual is subject to change without notice and does not represent a

commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be

contained in this User’s Manual. PLANET makes no commitment to update or keep current the

information in this User’s Manual, and reserves the right to make improvements

and/or to the products described in this User’s Manual, at any time without notice.

If you find information in this man

yo

CE mark Warning

The is a class B device, In a domestic environment, this prod

ca

Trademarks

The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous

hardware and software products by their trade names. In most, if not all cases,

cl

Revision

User’s Manual for PLANET G.SHDSL Bridge/Router

Model: GRT-101/ GRT

Rev: 4.0 (Nov. 2007)

- -

2

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Table of Contents

Table of Contents...........................................................................................3

Chapter 1 Overview .......................................................................................1

SOFTWARE FEATURES......................................................................1

SOFTWARE SPECIFICATIONS ...........................................................1

ATM Protocol.........................................................................................1

PPP Support .........................................................................................2

Routing Capability.................................................................................2

Bridging.................................................................................................2

Configuration.........................................................................................2

Network Management...........................................................................2

Hardware Specification .........................................................................3

Chapter 2 Installation.....................................................................................4

2.1 Front Panel LEDs...................................................................................4

2.2 Rear Panel Ports....................................................................................5

2.3 Rear Panel Connections ........................................................................5

2.4 Setting up the hardware environment.....................................................7

Chapter 3 Configuration................................................................................8

3.1 Purpose..................................................................................................8

3.2 Logon Procedure....................................................................................8

3.2.1 Serial console..................................................................................8

3.2.2 Telnet...............................................................................................9

3.2.3 Web browser....................................................................................9

3.3 Web operation and Quick Installation Guide ........................................10

3.3.1 Bridge Mode ..................................................................................10

Web UI Configuration..........................................................................11

Console Configuration.........................................................................12

3.3.2 Routing Mode for PPPoA and PPPoE with IP Sharing...................12

Web UI Configuration..........................................................................12

Console Configuration.........................................................................15

3.3.3 Routing Mode for IPoA or EoA.......................................................16

Web UI Configuration..........................................................................16

Console Configuration.........................................................................18

3.3.4 LAN-to-LAN Connection with Bridge Mode....................................19

Web UI Configuration..........................................................................19

- -

3

PLANET Technology Corp. GRT-101/401/402 User’s Manual

STU-C (CPE) side...............................................................................21

Console Configuration.........................................................................21

3.3.5 Advanced Setup.............................................................................22

SHDSL................................................................................................22

WAN....................................................................................................22

Bridge..................................................................................................24

Route ..................................................................................................24

NAT/DMZ ............................................................................................27

Virtual Server ......................................................................................28

3.3.6 Administration................................................................................29

Security...............................................................................................29

SNMP..................................................................................................30

Time Sync ...........................................................................................31

Config Tool..........................................................................................32

Upgrade ..............................................................................................33

Restart.................................................................................................33

3.3.7 Status.............................................................................................33

3.4 Command Line Interface......................................................................34

3.4.1 Multi-level password protection......................................................35

3.4.2 Menu Driven Command Line Interface ..........................................36

3.4.3 Command Line Interface Menu Tree..............................................36

3.4.4 Status.............................................................................................41

3.4.5 Show..............................................................................................41

3.4.6 Write ..............................................................................................41

3.4.7 Reboot...........................................................................................42

3.4.8 Ping ...............................................................................................42

3.5 Administration.......................................................................................42

3.5.1 User Profile....................................................................................42

3.5.2 Security..........................................................................................43

3.5.3 SNMP ............................................................................................43

3.5.4 Supervisor Password and ID .........................................................43

3.5.5 SNTP.............................................................................................44

3.6 Utility ....................................................................................................44

3.7 Exit .......................................................................................................44

3.8 Setup....................................................................................................45

3.8.1 Mode..............................................................................................45

3.8.2 SHDSL...........................................................................................45

3.8.3 WAN ..............................................................................................46

- -

4

PLANET Technology Corp. GRT-101/401/402 User’s Manual

- -

5

3.8.4 Bridge ............................................................................................47

3.8.5 Route.............................................................................................47

3.8.6 LAN................................................................................................47

3.8.7 IP share .........................................................................................47

3.8.8 DHCP.............................................................................................48

3.8.9 DNS proxy .....................................................................................48

3.8.10 Host name ...................................................................................48

3.8.11 Default..........................................................................................48

3.9 Connection Mode.................................................................................49

3.10 Bridging Mode....................................................................................49

3.10.1 Bridge management ....................................................................49

3.10.2 Static bridge table ........................................................................50

3.11 Routing Mode .....................................................................................51

3.11.1 LAN setting ..................................................................................51

3.11.2 Static routing table........................................................................52

3.11.3 NAT/PAT.......................................................................................53

3.11.4 DHCP server................................................................................56

3.11.5 DNS proxy....................................................................................56

3.12 WAN and ATM Virtual Connection......................................................57

3.12.1 SHDSL operation.........................................................................57

3.12.2 ATM virtual connection.................................................................58

3.12.3 ATM traffic shaping ......................................................................60

3.12.4 WAN IP address ..........................................................................61

3.12.5 ISP profile for PPP.......................................................................61

3.13 System Status and Performance........................................................63

3.14 User Profile.........................................................................................64

3.15 Management Security ........................................................................65

3.15.1 Telnet port number.......................................................................65

3.15.2 Legal client IP..............................................................................66

3.16 SNMP Support ...................................................................................67

3.16.1 SNMP community........................................................................67

3.16.2 SNMP trap...................................................................................68

3.17 Backup and Restore Configuration.....................................................68

3.17.1 Backup configuration ...................................................................68

3.17.2 Restore configuration...................................................................69

3.18 Software Upgrade ..............................................................................70

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Chapter 1 Overview

Based on digital subscriber line (DSL) technology, PLANET’s G.SHDSL

products, GRT series provide an affordable, flexible, efficient Internet access

solution for SOHO customers while reducing deployment and operational

costs from service providers. Via sending and receiving user’s datagram (often

Internet service) over existing telephone lines, GRT series concentrates all

traffic onto a single high-speed trunk for Internet activities or sharing a

corporate intranet. Through the simple-yet-powerful management UI of GRT

series, networks administrators can complete a managed network deployment

just in seconds.

SOFTWARE FEATURES

z Easy configuration and management with password control for various

application environments

z Efficient IP routing and transparent learning bridge to support

broadband Internet services

z VPN pass-through for safeguarded connections

z DMZ host / Multi-DMZ / Multi-NAT enables multiple workstations on the

LAN to access the Internet for the cost of IP address

z Fully ATM protocol stack implementation over SHDSL

z PPPoA and PPPoE support user authentication with PAP / CHAP /

MS-CHAP

z SNMP management with SNMPv1 / SNMPv2 agent and MIB II

z Getting enhancements and new features via firmware upgrade

z Built-in 4-port 10/100Mbps switch on GRT-401/GRT-402

z 4-wire supported in model GRT-402 double the bandwidth

SOFTWARE SPECIFICATIONS

ATM Protocol

ATM adaptation layer type 5 (AAL5)

VC multiplexing and LLC encapsulation

Multi-protocol over AAL5 (RFC 1483/2684 bridged and routed PDU)

Classical IP over ATM (RFC 1577 with MTU = 1500)

Up to 8 PVCs

Traffic shaping CBR/UBR

UNI 3.1/4.0 PVC

- -

1

PLANET Technology Corp. GRT-101/401/402 User’s Manual

I.610 OAM F5 loopback

PPP Support

PPP (RFC 1661)

PPP over AAL5 (RFC 2364)

PPP over Ethernet (RFC 2516)

User authentication with PAP/CHAP/MS-CHAP

Routing Capability

Support IP/TCP/UDP/ARP/ICMP/IGMP protocols

IP routing with static routing and RIPv1/RIPv2 (RFC1058/2453)

IP multicast and IGMP proxy (RFC1112/2236)

Network address translation (NAT/PAT) (RFC1631)

NAT ALGs for ICQ/Netmeeting/MSN/Yahoo Messenger

DNS relay and caching (RFC1034/1035)

DHCP server (RFC2131/2132)

Bridging

IEEE 802.1D transparent learning bridge

Up to 128 MAC learning addresses

Configuration

Local console (RS232)

Telnet access

Web-based GUI (HTTP)

Multi-level password protection

Network Management

Web-based GUI for express setup, configuration and management

Menu-driven interface/Command-line interface (CLI) for local console and

Telnet access

Password protected management and access control list for administration

SNMP management with SNMPv1/SNMPv2c (RFC1157/1901/1905) agent

and MIB II (RFC1213/1493)

Software upgrade via web-browser/TFTP server

- -

2

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Hardware Specification

WAN/LAN Ports RJ-11 SHDSL WAN port x1

10/100Mbps LAN port x1 on GRT-101

10/100Mbps LAN port x4 on GRT-401/GRT-402

Connector RJ-11 connector for WAN, RJ-45 connector for LAN

Cabling

Requirement

G.SHDSL : AWG26 or higher

10 /100 Base T: UTP/STP Category 3 or 5

LEDs SHDSL, Power Status, WAN Link and Action Status, LAN

Link/Active (and 100M Status), Alram

Speed SHDSL: 64Kbps to 2.304Mbps or

128Kbps to 4.608Mbps (for GRT-402, 4-wire

mode)

LAN Switch: 10/100 Mbps

Power External power adapter 9V DC, 1000mA

Environmental Operating temperature: 0° to 45°C

Storage temperature: -10° to 70°C

Housing Plastic Case

Dimension 145 mm x 187 mm x 33 mm (L x W x H)

- -

3

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Chapter 2 Installation

2.1 Front Panel LEDs

The LEDs on the front panel indicate the operational status of GRT series.

Figure 2-1 GRT-101 Front Panel

Figure 2-2 GRT-401 Front Panel

Figure 2-3 GRT-402 Front Panel

The following table describes the LEDs’ functions:

Table 2-1 GRT-101 LED Functions

LEDs Active Color Description

PWR On Green Power adaptor is connected to GRT-101/GRT-401

LNK On Green SHDSL line connection is established

WAN

ACT On Green Transmit or received data over SHDSL link

10/ACT On Green LAN Speed operates in 10M

LAN

100/ACT On Green LAN Speed operates in 100M

ALM On Red SHDSL connection disconnected

- -

4

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Table 2-2 GRT-401/GRT-402 LED Functions

LEDs Active Color Description

PWR On Green Power adaptor is connected to GRT-101/GRT-401

LNK On Green SHDSL line connection is established

WAN

ACT On Green Transmit or received data over SHDSL link

1 On Green Transmit or received data over LAN 1

2 On Green Transmit or received data over LAN 2

3 On Green Transmit or received data over LAN 3

LAN

4 On Green Transmit or received data over LAN 4

ALM On Red SHDSL connection disconnected

2.2 Rear Panel Ports

The connectors on the rear panel provide Power, LAN, CONSOLE and LINE

interfaces.

Figure 2-4 GRT-101 Rear Panel

Figure 2-5 GRT-401/GRT-402 Rear Panel

The following table describes the connectors’ functions:

Table 2-3 Connector Functions

Connectors Description

DC-IN Power adaptor inlet: Input voltage 9VDC

LAN Ethernet interface for LAN port (RJ-45)

CONSOLE RS- 232C (DB9) for system configuration and maintenance

LINE SHDSL interface for WAN port (RJ-11)

RST Reset button for factory default

2.3 Rear Panel Connections

The figure shows the rear panel connections of GRT series.

- -

5

PLANET Technology Corp. GRT-101/401/402 User’s Manual

The STU-R is a standalone and can able to place in desktop. All the external

wiring shall be located at the rear panel. The LAN port is a 10 Base-T /

100Base-TX auto-sensing and half/full duplex Ethernet interface and complied

with IEEE 802.3 / 802.3u respectively. The console (RS-232C) interface for

configuration is menu-driven operation and can also be configured through

Ethernet interface by Telnet or Web-based operation.

Power Adpter

Wall Jack

RJ-45 Cable

PC

NB

DB-9 Cable

Figure 2-6 Direct Connection with PC or NB

Power Adpter

Wall Jack

Console

Cable

Switch / Hub

Server

PC

NB

MAC

Mobile Device

Wireless AP

Figure 2-7 Connection with Switch or HUB

Note: GRT-401/GRT-402 support Auto-MDI (media dependence interface) that

auto-detect MDI or MDI-cross with link partner, a standard straight wire UTP

cable (EIA568) can be deployed to connect to a PC or Ethernet devices like

hub/switches. GRT-101 supports MDI interface only.

- -

6

PLANET Technology Corp. GRT-101/401/402 User’s Manual

2.4 Setting up the hardware environment

Step 1: Connect the power adapter to the port labeled DC-IN on the rear

panel of the product.

Step 2: Connect the Ethernet cable.

If GRT-101 is directly connected to PC, the Ethernet cable has to be

used cross over one (refer to figure 2-6). If the product is connected

to hub or switch, be sure that the hub or switch supporting

auto-MDI/MDI-X or not. If yes, both crossover and non-crossover

Ethernet cable are suitable. If not, only non-crossover Ethernet cable

could be used (refer to figure 2-7). Since GRT-401 and GRT-402’s

LAN port supports auto-MDI/MDI-X, both crossover and

non-crossover Ethernet cable are suitable.

Step 3: Connect the phone cable to the product. Connect the other side of

phone cable to wall jack.

Step 4: Connect male end of RS-232 cable to the product and female end to

any free COM port in PC.

Step 5: Connect the power adapter by plugging power supply.

- -

7

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Chapter 3 Configuration

3.1 Purpose

This chapter provides information about configuring GRT series.

Note: After you have completed all necessary setting for GRT series, make sure to write the new configuration to

NVRAM by “write” command and reboot the system, or all of your changes will not take effect.

3.2 Logon Procedure

There are three methods to logon to GRT series: serial console, Telnet, and

web interface. For the first time configuration, perhaps only the serial console

mode could be used because applications requiring Internet protocol (IP)

communication, such as Telnet and web interface, are not available unless a

management IP is configured properly for your local networking environment.

After connecting all the necessary cables described in Chapter 2 Installation,

power on GRT series and select one of the following procedures to access

GRT series.

Note: It is recommended that only one configuration application is used to setup GRT series at any given time, that is,

Telnet, serial console and the web management interfaces should not be used simultaneously.

3.2.1 Serial console

Check the connectivity of the RS-232 cable from your computer to the serial

port of GRT series. Start your terminal access program with VT100 terminal

emulation. Configure the serial link with baudrate of 9600, 8 data bits, no parity

check, 1 stop bit, and no flow-control, and press the SPACE key until the login

screen appears. When you see the login screen, you can logon to GRT series.

User: admin

Password: *****

Note: If you have not set any user profile for GRT series, enter the factory default user “admin”. When the system

prompts you for a password, type “admin” to enter GRT series.

After you logon to GRT series and before proceeding any further, check the

software version of GRT series by the command:

- -

8

PLANET Technology Corp. GRT-101/401/402 User’s Manual

admin> show system

If firmware file is downloaded from our local distributor or FTP server, please

refer to TFTP command in the section 3.18 Software Upgrade for more

information on how to update GRT series firmware.

3.2.2 Telnet

Make sure the correct Ethernet cable is used for connecting the LAN port of

your computer to GRT series. The LAN LNK indicator on the front panel shall

light if a correct cable is used. Starting your Telnet client with VT100 terminal

emulation and connecting to the management IP of GRT series, wait for the

login screen appears. When you see the login screen, you can logon to GRT

series.

User: admin

Password: *****

Note: The factory default management IP and subnet mask are of 192.168.0.1 and 255.255.255.0, respectively. To

change these setting, see section 3.10.1 Bridge management and 3.11.1 LAN setting for routing mode operation. If

you have not set any user profile for GRT series, enter the factory default user “admin”. When the system prompts you

for a password, type “admin” to enter GRT series. For more security issues for remote management interfaces such

as Telnet and web interface, see section 3.15 Management Security.

3.2.3 Web browser

Make sure the correct Ethernet cable is used for connecting the LAN port of

your computer to GRT series. The LAN LNK indicator on the front panel shall

light if a correct cable is used. Starting your web browser and connecting to the

management IP of GRT series, wait for the login screen appears. When you

see the login screen, you can logon to GRT series.

Note: In this chapter, we use the GRT-101’s Web UI for the examples.

Note: The factory default management IP and subnet mask are 192.168.0.1 and 255.255.255.0 respectively. To

change these setting, see section 3.10.1 Bridge management and 3.11.1 LAN setting. If you have not change

password setting for web interface, enter the factory default user “root”. When GRT prompts you for a password, type

“root”. More security issues for remote management interfaces, please refer to section 3.15 Management Security.

- -

9

PLANET Technology Corp. GRT-101/401/402 User’s Manual

3.3 Web operation and Quick Installation

Guide

3.3.1 Bridge Mode

- -

10

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Web UI Configuration

After connection via web browser, click BRIDGE and CPE Side to setup

Bridging mode of GRT series and then click Next for the next setting.

1. Enter WAN1 VPI: 0 and VCI: 32.

2. Select WAN1 AAL5 Encap: LLC

3. Enter LAN IP: 192.168.0.1

4. Enter LAN Sub-net Mask: 255.255.255.0

5. Enter Gateway: 192.168.0.254

The Gateway is directly pointed to the BAS IP.

6. Click Next

7. The screen will prompt the new configured parameters. Check the

parameters and click Restart, the router will reboot with the new setting or

click Continue to configure other parameters.

- -

11

PLANET Technology Corp. GRT-101/401/402 User’s Manual

Console Configuration

Do the following steps:

1 User : admin « password: admin «

2 enable « supervisor password: root «

3 setup « mode « Bridge «

4 wan « Interface number (1~8) : 1 «

Protocol « : Ethernet «

vpi_vci : 0 «

32 «

encap : LLC «

5 bridge « gateway « 192.168.0.254 «

6 lan«address« 192.168.0.1 «

255.255.255.0«

7 (back to root) write « y «

y «(reboot)

3.3.2 Routing Mode for PPPoA and PPPoE with IP

Sharing

Web UI Configuration

For Route Mode with Point-to-Point Protocol over ATM and Ethernet, follow the

following setting. First select ROUTE and CPE Side, and then click Next for

setting others parameters.

- -

12

PLANET Technology Corp. GRT-101/401/402 User’s Manual

1. Enter LAN IP: 192.168.0.1

2. Enter LAN Sub-net Mask: 255.255.255.0

3. Host Name: SOHO

4. DHCP Server: Enable

5. Click Next

6. Enter DHCP Client Start IP: 192.168.0.2

7. Enter DHCP Client End IP: 192.168.0.51

8. Enter DNS Server: 192.168.0.1

9. The DNS server is embedded in GRT series.

10. Click Next to write the new setting.

- -

13

PLANET Technology Corp. GRT-101/401/402 User’s Manual

11. Enter WAN1 VPI: 0 and VCI: 32.

12. Select WAN1 AAL5 Encap: LLC

13. Select: PPPoA + NAT or PPPoE + NAT

14. Click Next

15. Enter user name provided by ISP: user1@net

16. Enter Password provided by ISP: user1

17. Re-enter Password for confirmation: user1

- -

14

PLANET Technology Corp. GRT-101/401/402 User’s Manual

18. The screen will prompt the new configured parameters. Check the

parameters and click Restart, the router will reboot with the new setting or

click Continue to configure other parameters.

Console Configuration

Do the following steps:

1. User : admin « password: admin «

2. enable « supervisor password: root «

3. setup « mode « Route «

4. wan « Interface number (1~8) : 1 «

protocol « PPPoA or PPPoE «

vpi_vci: 0 «

32 «

encap « LLC «

isp «account: user1@net «

password: user1 «

idle time out: 0 ~ 600 « (the unit is in minute)

5. lan « address « 192.168.0.1 «

255.255.255.0 «

attrib « Virtual «

6. (back to root) write « y «

y «(reboot)

- -

15

Page is loading ...

Planet GRT-401 User manual

This manual is also suitable for

Planet GRT-401 User manual

Related papers

Other documents