Martin MAC 2000 Wash XB User manual

Brand: Martin

Model: MAC 2000 Wash XB

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

MAC 2000 Wash

MAC 2000 Wash

user manual

IMENSIONS

750

613

488

171

408

28°

133½°133½°

280

765

270°270°

490

562

min c/c

14°

All dimensions are given in millimeters

panies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by

the use of, inability to use or reliance on the information contained in this manual. The Martin logo, the Martin name and all other

trademarks in this document pertaining to services or products by Martin Professional A/S or its affiliates and subsidiaries are trade-

marks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.

P/N 35000114 Rev. L

ONTENTS

DIMENSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Included items. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Transport locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Cardboard box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Single flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Double flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

AC POWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Reduced power function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Connecting fixtures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

RIGGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DMX address and protocol setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Tailoring performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Readouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Service messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Service utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

EFFECTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Dimming and strobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Color temperature correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Motorized zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Beam angles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Motorized barndoors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Aperture adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Pan and tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Speed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

OPTICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Color wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Changing the front lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Changing the aperture ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Installing the optional dimmer wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

The lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Replacing the lamp socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Software installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

16-bit protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

8-bit protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

CONTROL MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

ADJUSTMENT SUBMENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

DISPLAY MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

CIRCUIT BOARD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

MAC 2000 WASH SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Notes

Safety Information 5

Safety Information

The following symbols are used to identify important safety information on the product and in this manual:

This product is for professional use only. It is not for household use.

This product presents risks of severe injury or death due to fire and burn hazards, electric shock, lamp

explosion and falls.

Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed

below and observe all warnings in this manual and printed on the fixture. If you have questions about how to

operate the fixture safely, please contact your Martin supplier or call the Martin 24-hour service hotline on

+45 8740 0000, or in the USA on 1-888-tech-180.

PROTECTION FROM ELECTRIC SHOCK

• Disconnect the fixture from AC power before removing or installing any cover or part – including the lamp

and fuses – and when not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical codes and has both

overload and ground-fault (earth-fault) protection.

• Connect this fixture to AC power either using the supplied power cable or via 3-conductor cable that is

rated minimum 16 amp, extra hard usage. Suitable cable types include ST, STW, SEO, SEOW and STO.

• Before using the fixture, check that all power distribution equipment and cables are in perfect condition

and rated for the current requirements of all connected devices.

• Do not use the fixture if the power cable or power plug are in any way damaged, defective or wet, or if they

show signs of overheating.

• Do not expose the fixture to rain or moisture.

• Refer any service operation not described in this manual to a qualified technician.

WARNING!

Read the safety precautions in this section before

installing, powering, operating or servicing this

product.

Warning!

Safety hazard.

Risk of severe

injury or death.

Warning!

Refer to

manual before

installing,

powering or

servicing.

Warning!

Hazardous

voltage. Risk of

lethal or severe

electric shock.

Warning!

Fire hazard.

Warning!

Burn hazard.

Hot surface. Do

not touch.

Warning!

Risk of eye

injury. Safety

glasses must

be worn.

Warning!

Risk of hand

injury. Safety

gloves must be

worn.

6 MAC 2000 Wash

LAMP SAFETY

• Prolonged exposure to an unshielded discharge lamp can cause eye and skin burns. Do not stare directly

into the light output. Never look at an exposed lamp while it is lit.

• Do not operate the fixture with missing or damaged covers, shields, lenses or ultraviolet screens.

• A hot discharge lamp is under pressure and can explode without warning. Allow the fixture to cool for at

least 45 minutes and protect yourself with safety glasses and gloves before handling a lamp or servicing

the fixture internals.

• Replace the lamp immediately if it becomes visually deformed, damaged or in any way defective

• Monitor hours of lamp use and lamp intensity and replace the lamp when it reaches the limit of its service

life as specified in this manual or by the lamp manufacturer.

• Install only an approved lamp.

• If the quartz envelope of a discharge lamp is broken, the lamp releases a tiny quantity of mercury vapor

and other toxic gases. If a discharge lamp explodes in a confined area, evacuate the area and ventilate it

thoroughly. Wear nitrite gloves when handling a broken discharge lamp. Treat broken or used discharge

lamps as hazardous waste and send to a specialist for disposal.

PROTECTION FROM BURNS AND FIRE

• The exterior of the fixture becomes very hot – up to 175° C (347° F) – during use. Avoid contact by

persons and materials. Allow the fixture to cool for at least 45 minutes before handling.

• Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the

specified type and rating.

• Keep all combustible materials (e.g. fabric, wood, paper) at least 1 m (39 in.) away from the fixture. Keep

flammable materials well away from the fixture.

• Do not illuminate surfaces within 3 m (10 ft.) of the fixture.

• If a fresnel lens (medium beam angle) or a micro-fresnel lens (very narrow beam angle) is installed,

position the head so that the lens does not face the sun directly at any time during daylight hours. These

two lenses can focus the sun's rays inside the fixture, creating a possible fire risk.

• Provide a minimum clearance of 0.1 m (4 in.) around fans and air vents.

• Never stick filters, masks or other materials onto any lens or other optical component.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

PROTECTION FROM INJURY DUE TO FALLS

• Do not lift or carry the fixture alone.

• Use two evenly spaced clamps to suspend the fixture from rigging structures. Do not use only one clamp.

• When suspending the fixture, ensure that the structure and all hardware used can hold at least 10 times

the weight of all devices suspended from them.

• Use a secondary attachment such as a safety cable that is approved for the weight of the fixture and

installed as described in this manual.

• Check that all external covers and rigging hardware are securely fastened.

• Block access below the work area and work from a stable platform whenever installing, servicing or

moving the fixture.

Disposing of this product

Martin™ products are supplied in compliance with Directive 2002/96/EC of the European

Parliament and of the Council of the European Union on WEEE (Waste Electrical and Electronic

Equipment), as amended by Directive 2003/108/EC, where applicable.

Help preserve the environment! Ensure that this product is recycled at the end of its life. Your

supplier can give details of local arrangements for the disposal of Martin products.

Introduction 7

NTRODUCTION

Thank you for selecting the MAC 2000 Wash. The MAC 2000 Wash is a 1200 Watt moving head wash light

that provides CMY color mixing, color correction (CTC), two color wheels (each with four removable colors),

a combined dimmer/shutter. 540° of pan and 267° of tilt. A motorized barndoor system and optional dimmer

wheel are available as a separately orderable accessory.

The MAC 2000 Wash has a Fresnel lens fitted as standard, and is also supplied with a PC lens and a super

wide-angle lens. A motorized zoom provides beam angle ranges of 11° through to 40° (in the standard

Fresnel configuration), 12° through to 34° (with the PC lens fitted), or 66° through to 80° (with the super

wide-angle lens fitted).

The MAC 2000 Wash is fitted with an electronic ballast that provides flicker-free operation and an

economical power-saving mode. The switch mode power supply unit is auto ranging to match 100 - 120 V or

208 - 240 V nominal AC power. It adapts automatically to 50 or 60 Hz power..

Note: This manual describes functionality available from version 1.7 of the MAC 2000 Wash

software. For the latest software updates, documentation, and other information about this

and all Martin Professional products, please visit the Martin website at

http://www.martin.com.

Important! Release the transport locks before operating the fixture.

Included items

The MAC 2000 Wash is shipped in a cardboard box or in a

1 or 2-unit flightcase that contains the following items.

• This user manual

• Philips MSR 1200 SA/DE Gold lamp (installed)

• Two Omega clamp attachment brackets, 1/4-turn

• DMX cable with 3-pin XLR connectors

• Very narrow-angle front module with micro-Fresnel lens

• Narrow-angle front module with PC (plano-convex) lens

• Medium-angle front module with Fresnel lens (installed)

• 30 mm (1.2 in.), 40 mm (1.6 in.), 45 mm (1.8 in.) and

50 mm (2 in.) aperture rings

• 2 x 20 A main fuses (for use with 100 - 120 V power)

• 2 x 15 A main fuses (for use with 208 - 240 V power)

Note: Products up to late 2008 did not contain the very narrow micro-Fresnel lens but contained a very

wide-angle lens assembly instead. The wide-angle lens is still available as an accessory and can be

ordered using P/N 55203012 “Front module, super wide lens, MAC 2000 Wash”.

Transport locks

The head and yoke may be locked for transportation and service. The locks are shown in Figure 1. The

fixture must be unlocked before operation.

Cardboard box

Instructions for removing models that have been shipped in a cardboard box are printed on the outside of

the box. The cardboard box is not designed for repeated use and for transportation of the fixture we strongly

recommend the use of one of our flight cases.

Figure 1: Pan and tilt locks

8 MAC 2000 Wash

Single flight case

Unpacking the fixture

1 Remove the top of the flight case.

2 With one person on each side, lift the fixture out of the

bottom of the flight case.

3 Release the pan and tilt locks before operating.

Packing the fixture

1 Disconnect the fixture from power and allow it to cool.

2 Lock the head and yoke in the position shown in Figure 2.

3 Place the fixture in the bottom of the flight case. Place the

top section over the fixture without forcing.

Double flight case

Unpacking

1 Open the flight case and pull the drawer all the way out.

2 Release the head (tilt) transport lock.

3 Install rigging hardware as described on page 12.

4 With one person on each side, lift the fixture out of the flight

case.

Packing

1 Disconnect the fixture from power and allow it to cool.

2 Turn the yoke parallel to the sides of the base with the tilt

lock closest to the back of the base.

3 Pull the transport drawer all the way out. With one person

on each side, place the fixture on the drawer with the

‘Front’ arrow pointing into the flight case.

4 Remove and stow rigging hardware. Coil and stow the

power cable in the door.

5 Tilt the head so that the lens points away from the door as

shown in Figure 3. Lock the head in the horizontal position.

Do not lock the yoke.

6 Slide the drawer all the way in without forcing. Close the flight case.

Setup for flight case testing

The double flight case has two slide-out arms from which the fixture can hang for testing and setting.

Though unnecessary, the pan and tilt reset can be cancelled by pressing [Menu] and [Enter] at the same

time.

1 Open the flight case and pull the drawer all the way out. Release the transport locks.

2 Pull the test arms out. Tilt the fixture up and over the test arms so that the handle cross-braces that are

second from the back rest on the arms. The fixture should rest at an angle.

3 Push the transport drawer into the flight case.

Figure 2: Single unit transport position

FRONT

Figure 3: Double unit transport position

AC power 9

POWER

WARNING! For protection from electric shock, the MAC 2000 Wash must be grounded (earthed). The

AC power supply must have both current overload and ground fault (earth leakage)

protection.

Do not connect the MAC 2000 Wash to power that is outside the voltage range specified in

this manual and marked on the product.

Check that the correct fuses for your AC power voltage are installed before operating the

MAC 2000 Wash (see below).

Power supply

The MAC 2000 Wash can be operated on either 100 - 120 V or 208 - 240 V nominal AC power. It has a full

auto-ranging power supply that adjusts automatically to match AC voltage within these ranges and to match

50 or 60 Hz power.

Older models (before Serial Number 4017886001) in the MAC 2000 series were supplied with a semi

auto-ranging power supply unit that must be switched manually to set the fixture for 100-120 V or 208-240 V

power. If you have an older model MAC 2000 Wash that has not been retrofitted with the newer full

auto-ranging power supply unit, please refer to Revision H of this user manual, available for download from

http://www.martin.com. If you are in any doubt as to which power supply unit you have, or have any

questions, please contact your Martin dealer for assistance.

Fuses

The MAC 2000 Wash is supplied with:

• two 20 AT (time delay) main fuses for use with 100 - 120 Volts AC power.

• two 15 A main fuses for use with 208 - 240 Volts AC power.

Install the correct fuses for your AC power voltage in the fuseholders near the power switch.

Power connection

Important! Connect the MAC 2000 Wash directly to AC power. Do not connect it to a dimmer system;

doing so may damage the fixture.

You may need to install a power plug that is suitable for your region on the power cable. A 3-prong

grounding-type plug must be installed following the plug manufacturer’s instructions. The table below shows

some possible pin identification schemes; if the pins are not clearly identified, or if you have any doubts

about proper installation, consult a qualified electrician.

To apply power, set the power switch on the base to the “I” position.

Wire Color Pin Symbol Screw (US)

brown live L yellow or brass

blue neutral N silver

yellow/green ground green

Table 1: Power plug connections

10 MAC 2000 Wash

Reduced power function

The MAC 2000 Wash has an automatic power reduction function that reduces the consumption to 700 W if

the shutter/dimmer is closed for more than 10 seconds. This not only increases lamp life but also further

decreases the overall noise emission of the fixture.

Data 11

ATA

Important! Do not connect more than 1 data input and 1 data output at any one time.

The MAC 2000 Wash has both 3-pin and 5-pin XLR sockets for DMX input and output. The pin-out on all

sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5.

The sockets are wired in parallel: both inputs connect to both outputs. For reliable data transmission and to

avoid damage to the fixture, however, use one input and one output!

Connecting fixtures

• Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit

control data reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters (1000 ft). Heavier

gauge cable and/or an amplifier is recommended for longer runs.

• Never use both outputs to split the link. To split the serial link into branches use a splitter such as the Martin

4-Channel Opto-Isolated RS-485 Splitter/Amplifier.

• Do not overload the link. Up to 32 devices may be connected on a serial link.

• Terminate the link by installing a termination plug in the output socket of the last fixture. The termination

plug, which is a male XLR plug with a 120 Ohm, 0.25 Watt resistor soldered between pins 2 and 3, “soaks

up” the control signal so it does not reflect and cause interference. If a splitter is used, terminate each

branch of the link.

Connecting the data link

1 Connect the DMX data cable from the controller to the MAC 2000 Wash’s 3-pin or 5-pin input (male) socket.

2 Using the sockets that match your data cable, connect the output of the fixture closest to the controller to the

input of the next fixture.

3 Insert a male DMX termination plug (see “Accessories” on page 50) in one of the XLR outputs of the last

fixture on the link.

12 MAC 2000 Wash

IGGING

The MAC 2000 Wash can be placed on stage or clamped to a truss in any orientation. The Fast-Lock

system enables quick and easy fastening of the clamp brackets in 4 positions as shown Figure 4.

Warning! Always use 2 clamps to rig the fixture. Lock each clamp with both 1/4-turn fasteners. The

fasteners are locked only when turned fully clockwise.

Attach an approved safety cable to the attachment hole in the base. Never use the carrying

handles for secondary attachment.

When a fresnel lens (medium beam angle) or a micro-fresnel lens (very narrow beam angle)

is installed, the head must be positioned so that the lens does not face the sun directly at

any time during daylight hours. These two lenses can focus the sun's rays inside the

fixture, causing internal damage and creating a possible fire risk.

Clamping the fixture to a truss

1 Verify that the rigging clamps (not included) are undamaged and can bear at least 10 times the weight of the

fixture. Verify that the structure can bear at least 10 times the weight of all installed fixtures, clamps, cables,

auxiliary equipment, etc.

2 Bolt each clamp securely to a clamp bracket with an M12 bolt (grade 8.8 or better) and lock nut.

3 Align a clamp with 2 mounting points in the base. Insert the fasteners into the base and turn both levers a

full 1/4-turn clockwise to lock. Install the second clamp.

4 If the truss can be lowered, fixtures can be clamped on directly from the double flight case. If the fixture

must be lifted, block access under the work area. Working safely from a stable platform, hang the fixture on

the truss with the arrow towards the area to be illuminated. Tighten the rigging clamps.

5 Install a safety wire that can bear at least 10 times the weight of the fixture. The attachment point is

designed to fit a caribiner clamp.

6 Verify that the pan and tilt locks are released. Verify that there are no combustible materials or surfaces to

be illuminated within 1 meter (39 inches) of the fixture, and that there are no flammable materials nearby.

256

Figure 4: Clamp bracket positions

Rigging 13

FRONT

Figure 5: Rigging hardware installation

14 MAC 2000 Wash

ONTROL

PANEL

The LED control panel is used to set the address and personalities, read lamp hours and other information,

calibrate effects, and run a test routine. Most of these functions may be performed remotely via the serial

link with the Martin MP-2 Uploader.

Navigation

The DMX address and any messages (see page 44) are displayed when the MAC 2000 Wash is turned on.

To enter the menu, press [Menu]. Press [Up] and [Down] to move within the menu. To select a function or

submenu, press [Enter]. To escape a function or menu, press [Menu].

See “Control menu” on page 38 for a complete list of the menu items.

Note: [Enter] must be pressed and held for a few seconds to enter the utilities menu.

DMX address and protocol setting

The DMX address, also known as the start channel, is the first channel used to receive instructions from the

controller. For independent control, each fixture must be assigned its own control channels. Two MAC 2000

Washs may share the same address, however, if identical behavior is desired. Address sharing can be

useful for diagnostic purposes and symmetric control, particularly when combined with the inverse pan and

tilt options.

Two DMX protocols, 8-bit and 16-bit, are available. The 8-bit mode uses 19 control channels and provides

full basic control. The 16-bit mode uses 2 additional channels to provide finer pan/tilt positioning.

Setting the DMX address and protocol

1 Press [Menu] to enter the main menu.

2Press [Up] until

 is displayed. Press [Enter]. To snap to channel 1, press [Enter] and [Up]. Scroll to

the desired channel and press [Enter].

3 Select

 from the main menu and press [Enter]. Select  or  and press [Enter].

Tailoring performance

Movement

The MAC 2000 Wash provides six options for optimizing movement for different applications. The:

• Protocol setting (

) setting selects 8-bit or finer 16-bit control of pan and tilt.

• Pan and tilt invert (

) menu swaps and/or inverts pan and tilt.

• Pan/tilt speed (

) menu provides 3 settings: , , and .

 is best for most applications.  provides better performance in applications where speed is

most important.

 provides the smoothest movement and is best in long-throw applications with slow

movements through narrow angles.

• Studio mode (

) setting optimizes all effects besides pan and tilt for speed or quietness.

• Shortcuts (

) setting determines whether the color wheels always take the shortest path between two

static positions or oscillate between outer positions.

Tracking Response

The MAC 2000 Wash has a filter algorithm that looks at several position updates in tracking control mode

and calculates the ideal response for smooth movement. Tracking response is adjustable to compensate for

variations in controller performance. In most cases the default settings work well.

Control panel 15

If tracking mode movement is not satisfactory there are 2 parameters that can be adjusted. The first is

selected under

→→. The default, , is the best choice with controllers that

calculate intermediate positions at a steady rate. Begin by selecting the alternative,

, which is better

if the intermediate positions stray significantly from the line of travel.

The second parameter is the number of position updates used to calculate speed. The level is adjustable

between 1 and 10 under

→→. Increasing the number of samples increases the distance

over which speed is calculated, making movement smoother but less responsive to sudden changes.

Experiment for best results.

Display

The display intensity () setting controls display brightness. The display on/off setting ()

determines whether the display remains on or extinguishes two minutes after the last key-press. To flip the

display, press [Up] and [Down] simultaneously.

Lamp

There are two settings that modify lamp control: Automatic Lamp On () and DMX Lamp Off ().

When  is off, the lamp remains off until a “lamp on” command is received from the controller. When

 is on, the lamp strikes automatically after the fixture is powered on. When  is set to , the

lamp strikes automatically when the fixture receives DMX data, and it extinguishes 15 minutes after DMX

data is lost.

When

 is set to either  or , the automatic lamp strike timing is staggered to prevent all lamps

from striking at once. The delay is determined by the fixture address.

If striking lamps from the controller, note that striking many lamps at once may cause a voltage drop large

enough to prevent lamps from striking or trip the main circuit breaker. Avoid this by programming a “lamp

on” sequence that strikes lamps one at a time at 5 second intervals.

Power to the lamp can be turned off from the controller if DMX Lamp Off (

) is on.

Shutter dimming curves

Two dimming curves are available for the mechanical shutter system for adjusting intensity

(

→). The default, dimmer curve 1, simulates the dimming of a tungsten lamp. Dimmer curve 2

applies a linear algorithm to intensity adjustment, that results in even adjustment across the whole dimming

range. Note that this setting has no effect on the optional dimming wheel, that uses a logarithmic dimming

curve.

DMX reset

The fixture can be reset from the controller if DMX reset (→) is set to .

Custom settings

The custom configuration function allows you to save and recall three sets of fixture settings. The savable

settings are DMX mode, pan/tilt speed, pan/tilt inverse and swap, DMX lamp off and reset, display settings,

shortcuts, studio mode, automatic lamp on, effects feedback, tracking algorithm, and tracking samples.

Readouts

Note: The MP-2 Uploader provides commands to display the time, temperature, and version readouts on

the fixture control panel.

Time

→ provides readouts of fixture hours (), lamp hours (), and lamp strikes ().

Under each item is a resettable (

) increment counter and a non-resettable counter for total

accumulated hours/strikes since fabrication (

). To reset an increment counter, display it and then

press [Up] until it reads

 . (This may also be done remotely using the MP-2 Uploader.)

16 MAC 2000 Wash

Temperature

→ provides readouts of the head and base temperature in Celsius and Fahrenheit.

Software version

→ displays the version number of the installed software. The software version is also displayed

briefly at startup.

DMX

The  menu shows the DMX start code () and DMX values received for each effect.

Service messages

The Service LED on the control panel lights under conditions that require fixture service, and there is a

message describing the service required. To display the message, select

 in the main menu. This

item is available only when the LED is lit. There are two service messages.

 is displayed when the lamp counter exceeds 750 hours, which is the rated average

life for the HMI 1200 W/S lamp. Do not exceed the average life of the lamp by more than 10%.

is displayed when the head temperature exceeds 120° C (248° F).

Overheating is typically caused by trying to operate the fixture in ambient temperatures above 40° C

(104° F), dirty air filters, fans, or air vents; incorrect power supply settings, or a defective fan.

Service utilities

Important! Enter must be held for several seconds to access the utilities menu.

Test sequences

 provides a general test of all effects that can be run without a controller. → provides

routines for circuit board testing that are for service use only.

Feedback toggles

An on-the-fly position correction system monitors the color wheels. If a position error is detected, the shutter

closes while the effect resets. This feature can be disabled by turning effects feedback (

→)

off.

The automatic pan/tilt position correction system may be temporarily turned off under

→. The

off setting, however, is not saved and the system will be re-enabled the next time the fixture starts. If the

system cannot correct the pan/tilt position within 10 seconds, feedback is automatically disabled.

Adjustment

The adjustment menu (→) provides manual control for making mechanical adjustments and is

used by Martin service technicians.

Calibration

The calibration menu (→) provides utilities to define offsets in software that are relative to the

mechanical reset or home positions. This allows you to fine tune optical alignment and achieve uniform

performance between fixtures. Dimmer and zoom are calibrated to defined points. The other effects are

calibrated relative to an arbitrary reference fixture.

Default offset settings may be restored by selecting default offsets (

→).

Calibrating effects

1 Apply power and strike the lamp.

Control panel 17

2 To calibrate the zoom, select →→ and press [Enter]. The default value of 128 can be

adjusted up or down to move the diffuser lens relatively forward or back. Make any necessary adjustments

and press [Enter] to save the setting.

3 To calibrate the color wheels to an offset from their mechanically indexed position, select

→→ and press [Enter]. The default value of 128 can be adjusted up or down to move

the color wheel relatively forward or back from its indexed position. Make any necessary adjustments and

press [Enter] to save the setting. Repeat this procedure if necessary for color wheel 2 (

).

4 To calibrate the optional dimmer wheel to an offset from its mechanically indexed position, select

→→ and press [Enter]. The default value of 128 can be adjusted up or down to move

the dimmer wheel relatively forward or back from its indexed position. Make any necessary adjustments and

press [Enter] to save the setting.

5 Pan calibration is most useful when multiple fixtures are stacked vertically. To calibrate, set zoom, iris, and

tilt position for easy one-over-the-other comparison and set each fixture to the same pan DMX value. Select

one fixture to be the reference fixture. On the other fixtures, select

→→ and press

[Enter]. Adjust the offset as necessary to align the beam with the reference beam. Press [Enter] to save the

setting.

6 Tilt calibration is most useful when multiple fixtures are arranged horizontally. To calibrate, set zoom, iris,

and pan position for easy side-by-side comparison and set each fixture to the same tilt DMX value. Select

one fixture to be the reference fixture. On the other fixtures, select

→→ and press

[Enter]. Adjust the offset as necessary to align the beam with the reference beam. Press [Enter] to save the

setting.

7 To calibrate the dimmer, select

→→  and press [Enter]. Hold a piece of paper over the

lens. Set the offset to 0 and then increase it until light is clearly projected onto the paper. Press [Enter] to

save the setting. Remove the paper.

8 To calibrate color mixing flags (cyan, magenta, yellow, and color temperature correction), project white

beams with no dimming and position them for easy comparison. On each fixture, including the reference,

select

→→ and press [Enter]. (This adds a defined amount of cyan.) Select one fixture to

be the reference. Adjust the offsets on the other fixtures to match the reference color. Press [Enter] to save

the setting. Repeat for

 (magenta),  (yellow), and  (CTC).

Software upload

The software update mode is normally engaged automatically by the upload device. If this does not occur,

see “Software installation” on page 29.

18 MAC 2000 Wash

FFECTS

The MAC 2000 Wash is compatible with USITT DMX-512 controllers. The fixture has two DMX operating

modes, 8-bit and 16-bit. The 16-bit mode requires two more DMX channels than 8-bit mode but provides

more precise pan/tilt positioning. All other functions are identical. See “DMX protocol” on page 31.

Color

The color mixing system uses continuous dichroic cyan, magenta, and yellow (CMY) color filters. It is a

subtractive system that removes color from white light. Inserting all three filters results in loss of light: for

maximum brightness, mix 2 colors at a time.

In addition, two color wheels are provided, each with four removable positions for dichroic glass color filters

and a position for a direct pass through of the beam.

Dimming and strobe

Two dimming systems are available - a built-in mechanical dimmer/shutter and an optional dimmer wheel

(orderable separately).

Shutter

The mechanical shutter system provides full-range 100 percent dimming, instant open and blackout,

random and variable strobe effects up to 10 Hz, and random and variable pulses in which the dimmer snaps

open and slowly dims or snaps closed and slowly opens. Two dimming curves are available; one that

simulates a tungsten lamp and another that provides linear dimming (see “Shutter dimming curves” on

page 15).

Optional dimmer wheel

A separately orderable dimmer wheel (P/N 62324018) that provides enhanced dimming can be installed in

place of color wheel 2. The dimmer wheel uses a logarithmic algorithm that, compared with the dimming

available from the shutter system, enables much finer and smoother dimming at the bottom end of the

dimming range.

If you use the dimmer wheel, it is recommended that you do not use the shutter system to control intensity,

and that the shutters be set to fully open (ensure that 255 is the default DMX value issued on the shutter

intensity channel from your controller). You can continue to use other shutter effects, such as the strobe.

The wheel is detected automatically by the fixture when installed. The installation procedure is described in

“Installing the optional dimmer wheel” on page 24.

Color temperature correction

The color temperature correction (CTC) system uses a continuous 0 - 178 mireds color filter that lowers the

color temperature from 6000 K to 2900 K.

Motorized zoom

The zoom lens widens the beam from 11° at full spot to 40° at full flood with the standard lens and aperture

ring fitted.

Beam angles

The following tables list the beam angles available with the standard 50 mm (2 in) aperture ring fitted. Note

that narrower beam angles can be achieved by fitting smaller aperture rings. Note that Hypermode (also

Effects 19

known as light buster mode) provides a high intensity spot with no diffusion and is engaged when the zoom

channel is set to 100%.

A Very wide-angle front module containing a ‘Superwide’ lens is also available separately as an accessory

(P/N 91610092):

For information about changing the lens see “Changing the front lens” on page 23.

Motorized barndoors

A motorized barndoor system that attaches to the front of the fixture is available as a separately orderable

accessory. These barndoors can be rotated, or opened and closed using DMX control signals. Effective

beam cut off using the barndoor system is achieved only with the supplied 65 degree lens, or the super wide

angle lens supplied with the MAC 2000 Wash.

Five DMX channels are allocated for barndoor control irrespective of whether or not they are connected to

the fixture. We have done this to cover the possibility that you rig and begin programming your MAC 2000

Wash and add barndoors to it later. If the DMX channels were not already assigned, you would have to

re-patch your console and therefore would lose any programming already completed.

Aperture adjustment

A 50 mm (2 in) aperture is fitted as standard in the optical path of the fixture just behind the zoom lens. This

works well with the standard Fresnel lens.

Inside the head of the fixture, three additional aperture rings are secured to the chassis by a thumbscrew.

When using the PC lens, the best beam characteristic is achieved by attaching the 45 mm aperture ring. For

instructions on changing the aperture ring see “Changing the aperture ring” on page 24.

Medium (standard Fresnel lens) Half-peak angle 1/10 peak angle

Hypermode (Light buster mode) 7° 13°

Zoom minimum 8.5° 17°

Zoom maximum 28° 40°

Narrow (PC lens) Half-peak angle 1/10 peak angle

Hypermode (Light buster mode) 6.5° 12.5°

Zoom minimum 7.5° 14°

Zoom maximum 26° 37°

Very narrow (micro-Fresnel lens) Half-peak angle 1/10 peak angle

Hypermode (Light buster mode) 6.5° 9.5°

Zoom minimum 6.5° 12°

Zoom maximum 18° 33°

Very wide (‘superwide’ lens) Half-peak angle 1/10 peak angle

Hypermode (Light buster mode) 38° 75°

Zoom minimum 44° 80°

Zoom maximum 53° 95°

20 MAC 2000 Wash

Pan and tilt

The yoke pans 540° and the head tilts 267°. For maximum positioning accuracy, select 16-bit mode.

The pan/tilt speed (fast, norm, or slow) may be selected on the pan/tilt speed channel. Setting the pan/tilt

speed channel to “blackout” causes the shutter to black out the light while the head is moving.

Speed control

There are two ways to control the speed at which effects move from one static position to another. These

are known as tracking control and vector control and are selected on the Pan/Tilt Speed and Effect Speed

Channels. These channels are independent so you may, for example, combine a vector control pan

movement with a tracking control color fade.

In tracking mode, speed is determined by the cross-fade time. The controller continuously sends small

position changes that the fixture “tracks.” To enable tracking mode, set the relevant speed channel to a

tracking value. Note that in addition to enabling tracking control, some tracking values also provide

overrides of the menu settings.

In vector mode, speed is set directly on a speed channel. The cross-fade time must be 0. Vector control

provides a way to set speed on controllers that do not have programmable fade times and results in smooth

movement regardless of the cross-fade time or the controller’s processing power.

Page is loading ...

Martin MAC 2000 Wash XB User manual

Brand: Martin

Model: MAC 2000 Wash XB

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

MAC 2000 Wash

Download PDF

report

Martin MAC 2000 Wash XB User manual

This manual is also suitable for

Martin MAC 2000 Wash XB User manual

Related papers

Other documents