Henny Penny CBC/CBR-107 User manual

Brand: Henny Penny

Model: CBC/CBR-107

Category: Deep fryers

Type: User manual

Henny Penny

Cold Bases

Model CBC/CBR-103

Model CBC/CBR-104

Model CBC/CBR-105

Model CBC/CBR-106

Model CBC/CBR-107

OPERATOR’S MANUAL

Model CBC/CBR-103,104,105,106,107

LIMITED WARRANTY FOR HENNY PENNY APPLIANCES

Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the

original purchaser only for Henny Penny appliances and replacement parts:

NEW EQUIPMENT: Any part of a new appliance, except lamps and fuses, which proves to be defective

in material or workmanship within two (2) years from date of original installation, will be repaired or replaced

without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor. To validate this warranty, the

registration card for the appliance must be mailed to Henny Penny within ten (10) days after installation.

REPLACEMENT PARTS: Any appliance replacement part, except lamps and fuses, which proves to be

defective in material or workmanship within ninety (90) days from date of original installation will be repaired

or replaced without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor.

The warranty for new equipment and replacement parts covers only the repair or replacement of the defective

part and does not include any labor charges for the removal and installation of any parts, travel or other expenses

incidental to the repair or replacement of a part.

EXTENDED FRYPOT WARRANTY: Henny Penny will replace any frypot that fails due to manufacturing or

workmanship issues for a period of up to seven (7) years from date of manufacture. This warranty shall not cover

any frypot that fails due to any misuse or abuse, such as heating of the frypot without shortening.

0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship is-

sues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new

frypot at no cost or provide a new or reconditioned replacement fryer at no cost.

3 TO 7 YEARS: During this time, any frypot that fails due to manufacturing or workmanship is-

sues will be replaced at no charge for the frypot only. Any freight charges and labor costs to install

the new frypot as well as the cost of any other parts replaced, such as insulation, thermal sensors,

high limits, fittings, and hardware, will be the responsibility of the owner.

Any claim must be presented to either Henny Penny or the distributor from whom the appliance was purchased.

No allowance will be granted for repairs made by anyone else without Henny Penny’s written consent. If damage

occurs during shipping, notify the sender at once so that a claim may be filed.

THE ABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY

FOR ANY BREACH OF WARRANTY OR OTHER TERM. BUYER AGREES THAT NO OTHER REMEDY

(INCLUDING CLAIMS FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES) SHALL BE AVAIL-

ABLE.

The above limited warranty does not apply (a) to damage resulting from accident, alteration, misuse, or abuse;

(b) if the equipment’s serial number is removed or defaced; or (c) for lamps and fuses. THE ABOVE LIMITED

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-

ING MERCHANTABILITY AND FITNESS, AND ALL OTHER WARRANTIES ARE EXCLUDED. HENNY

PENNY NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER OB-

LIGATION OR LIABILITY.

FM01-879-C

Revised 02-09-06

Model CBC/CBR-103,104,105,106,107

TABLE OF CONTENTS

Section Page

Section 1. INTRODUCTION ...................................................................................................................1-1

1-1. Henny Penny Cold Bases ............................................................................................1-1

1-2. Features .......................................................................................................................1-1

1-3. Proper Care .................................................................................................................1-1

1-4. Assistance.................................................................................................................... 1-1

1-5. Safety........................................................................................................................... 1-2

Section 2. INSTALLATION......................................................................................................................2-1

2-1. Introduction ..................................................................................................................2-1

2-2. Unpacking .................................................................................................................... 2-1

2-3. Electrical ......................................................................................................................2-2

2-4. Location .......................................................................................................................2-3

2-5. Refrigerant Information ............................................................................................... 2-3

2-6. Drain Connection ......................................................................................................... 2-3

2-7. Compressor Size and Load ..........................................................................................2-4

2-8. Foot Print Drawing ...................................................................................................... 2-4

2-9. Fluorescent Lighting and lamp Replacement ............................................................... 2-5

2-10. Hot or Cold Top on a Cold Base Installation Instructions ............................................ 2-6

Section 3. OPERATION............................................................................................................................3-1

3-1. Introduction ..................................................................................................................3-1

3-2. Operating Controls .......................................................................................................3-1

3-3. Basic Operation ...........................................................................................................3-3

3-4. Cleaning .......................................................................................................................3-3

3-5. Programming................................................................................................................3-5

Wiring Diagram .........................................................................................................................3-7

303 i

Model CBC/CBR-103,104,105,106,107

1-1. COLD BASES The Henny Penny cold bases are self-serve units, designed to hold

chilled, or refrigerated products. The units are electronically

controlled for easy use and for consistent operation.

1-2. FEATURES • Can be matched with hot or cold merchandisers in all lengths

• Electronic controls

• Stackable units

• Low speed air circulation

• Easily maintained

• T8 fluorescent lighting with electronic ballast

(CE-magnetic ballast)

• Built-in dry storage area on remote units

• Self-serve units

• Remote or self-contained condenser models

• Insulated-well with high pressure injected polyurethane foam

• Automatic defrost cycles

1-3. PROPER CARE As in any unit of food service equipment, the Henny Penny cold

bases does require care and maintenance. Requirements for the

maintenance and cleaning are contained in this manual and must

become a regular part of the operation of the unit at all times.

1-4. ASSISTANCE Should you require outside assistance, just call your local indepen-

dent Henny Penny distributor in your area, or call Henny Penny

Corp. 1-800-417-8405 toll free or 1-937-456-8405.

503 1-1

SECTION 1. INTRODUCTION

Model CBC/CBR-103,104,105,106,107

1-5. SAFETY The Henny Penny cold bases have many safety features

incorporated. However, the only way to ensure a safe operation

is to fully understand the proper installation, operation, and

maintenance procedures. The instructions in this manual have

been prepared to aid you in learning the proper procedures.

Where information is of particular importance or safety related,

the words NOTICE, CAUTION, and WARNING, are used. Their

usage is described below.

SAFETY ALERT SYMBOL is used with DANGER,

WARNING, or CAUTION which indicates a personal injury

type hazard.

NOTICE is used to highlight especially important information.

CAUTION used without the safety alert symbol indicates

a potentially hazardous situation which, if not avoided,

may result in property damage.

CAUTION used with the safety alert symbol indicates a

potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

1-2 303

Model CBC/CBR-103,104,105,106,107

2-1. INTRODUCTION This section provides the installation and unpacking instructions for

the Henny Penny cold bases.

Installation of this unit should be performed only by a

qualified service technician.

Do not puncture the unit with any objects such as

drills or screws, or component damage or electrical

shock could result.

2-2. UNPACKING The Henny Penny cold base has been tested, inspected, and

expertly packed to insure arrival at its destination in the best

possible condition. The grids are packed separately inside the

unit. The cabinet rests on a wooden skid and is then packed inside

a heavy cardboard carton with sufficient padding to withstand

normal shipping treatment.

To avoid damage to the components, do not lay the unit

on its side. If the unit has been on its side, the unit must

be in an upright position for at least 4 hours before power

is applied to the unit.

Check all components, for signs of being loose or dam-

aged, and make sure the system has refrigerant.

When moving the cold base be careful not to damage the

refrigerant circuit.

Any shipping damage should be noted in the presence

of the delivery agent and signed prior to his or her

departure.

To remove the Henny Penny cold base from the carton:

1. Carefully cut banding straps.

2. Lift the carton off the unit.

3. Lift the unit off the skid.

303 2-1

SECTION 2. INSTALLATION

Model CBC/CBR-103,104,105,106,107

2-2. UNPACKING

Take care when moving the unit to prevent personal

injury or damage to the refrigeration system. The units

weigh between 400 (182 kg) and 580 lbs. (263 kg).

4. Peel off any protective covering from exterior of the cabinet.

5. Install the grids into unit.

6. Your cold base is now ready for operation.

2-3. ELECTRICAL The cold base is available as a 120 VAC, 60 Hz. or 230VAC,

50Hz, single phase unit, both for domestic and international use.

The data plate, located beside the power cord, specifies the correct

electrical supply. The cold bases are shipped with cord and plug,

and requires a grounded receptacle with a separate electrical line

protected by a fuse or circuit breaker of the proper rating. Position

the unit so the power cord receptacle is accessible.

To avoid electrical shock, this appliance must be

equipped with an external circuit breaker which will

disconnect all ungrounded (unearthed) conductors.

Refer to the table below for electrical ratings:

Model No. Volts Amps Phase Max. Fuse Size

CBC-103 120 8.1 1 15

CBC-103 230 5.8 1 15

CBC-104 120 8.1 1 15

CBC-104 230 7.3 1 15

CBC-105 120 9.5 1 15

CBC-105 230 7.5 1 15

CBC-106 120 9.5 1 15

CBC-106 230 7.5 1 15

CBC-107 120 9.5 1 15

CBC-107 230 7.7 1 15

(Continued)

2-2 303

Model CBC/CBR-103,104,105,106,107

303 2-3

2-4. LOCATION Place the cold bases in an area where product can be loaded and

unloaded without interruption. For proper operation, level the unit

by adjusting the bolts under the base, and leave 3 feet (91.44 cm)

clearance behind the unit for ventilation and service.

For maximum efficiency, units should be operated in an air-condi-

tioned environment, with maximum air temperature of 75° F

(24° C), and 55% relative humidity.

Wait at least 4 hours before plugging the unit into an

electrical supply. The gases and oils in the refrigeration

system need to settle before operating the compressor, or

damage to the compressor could result.

INFORMATION High Low

CBC-103 R22 2.5 lbs (1.134 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CBC-104 R22 2.5 lbs (1.134 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

UL Specs CBC-105 R22 2.5 lbs (1.134 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CBC-106 R22 2.5 lbs (1.134 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CBC-107 R22 2.5 lbs (1.134 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CBC-103 R134A 1.76 lbs (0.800 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CBC-104 R134A 2.20 lbs (1.00 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CE Specs CBC-105 R134A 2.65 lbs (1.200 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CBC-106 R134A 3.09 lbs (1.400 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

CBC-107 R134A 3.53 lbs (1.600 kg) 440psig 162 psig

(30.3 bar) (11.2 bar)

2-6. DRAIN CONNECTION The cold bases-remote (CBR), require 1 inch (25.4 mm) drain

connection. Cold bases with condensing units (CBC) do not

require a plumbed drain.

2-5. REFRIGERATION Refrigerant Type Amount of Refrig. Design Pressure

Model CBC/CBR-103,104,105,106,107

2-7. COMPRESSOR SIZE

AND LOAD

2-8. FOOT PRINT DRAWING

CBR MODELS

DRAIN & REFRIGERATION CONNECTIONS

2-4 403

Model CBC Motor HP CBR Motor HP

CBC/ BTU Load UL CE UL CE

CBR R-22 R-134a R-22 R-134a

103 2830 1/3 1/2 Remote

104 2830 1/3 1/2 Compressor

105 3840 1/2 1/2 Supplied

106 3840 1/2 1/2 By Other

107 3840 1/2 1/2

BTU load sized at evaporator temperature + 20 F or -6 C.

Model CBC/CBR-103,104,105,106,107

2-9. FLUORESCENT LIGHTING No.

AND LAMP REPLACEMENT Model of Lights Size

CBR/CBC-103 1 36 in. (.914 m)

CBR/CBC-104 1 48 in. (1.22 m)

CBR/CBC-105 1 24 in. (.610 m)

1 36 in. (.914 m)

CBR/CBC-106 2 36 in. (.914 m)

CBR/CBC-107 1 36 in. (.914 m)

1 48 in. (1.22 m)

UL Units

1. Pull the lamp out of the sockets.

2. Remove the lamp guard caps.

3. Install new fluorescent bulb in reverse order.

CE Units

1. Remove the lamp cover.

2. Rotate the lamp.

3. Pull the lamp out of the sockets.

4. Install new fluorescent lamp in reverse order.

303 2-5

Replacement:

Model CBC/CBR-103,104,105,106,107

2-10. HOT or COLD TOP ON A

COLD BASE INSTALLA-

TION INSTRUCTIONS

1. Remove bolts securing the top to the skid, and save bolts

for later use.

2. Carefully set top on top of the cold base.

Take care when moving the unit to prevent personal

injury or damage to the refrigeration system. The units

weigh between 400 (181 kg) and 580 lbs. (263 kg).

3. Line up the 2 front holes and secure the top to the base using

the bolts from step 1. Figure 2-1.

4. Locate mounting hole in right, rear corner of the units and se-

cure the corner using one of the bolts from step 1. Figure 2-2.

5. Pull the control panel out from unit and locate the mounting hole

in the left, rear corner. Secure corner with one of the screws

from step 1. Figure 2-3.

6. Installation is now complete.

Figure 2-1

Figure 2-2

Figure 2-3

2-6 303

Model CBC/CBR-103,104,105,106,107

3-1. INTRODUCTION This section provides explanations of all controls, along

with operating procedures and daily maintenance. Read the

Introduction, Installation and Operation Sections before

operating the unit.

Wait at least 4 hours before plugging the unit into an

electrical supply. The gases and oils in the refrigeration

system need to settle before operating the compressor, or

damage to the compressor could result.

3-2. OPERATING CONTROLS Refer to figure 3-1.

Fig. Item Description Function

No. No.

3-1 1 Power Switch A rocker switch that turns electrical power off and on to

the unit; located on the bottom of the control panel

3-1 2 Digital Display Shows the temperatures and the information in the Technical

Mode

3-1 3 The up and defrost button is used to increase setpoint

values, as well as programming values; also, automatic

defrost cycles are programmed in the controls, but to

manually start a defrost cycle, press and hold for 3

seconds to start a manual defrost cycle

(“DEF/SET’ shows in display)

3-1 4 The down button is used to decrease setpoint values, as

well as programming values

3-1 5 Press the set button to view the setpoint temperature, or

hold it for it for 4 seconds to enter the Program Mode;

once in the Program Mode, press to view other

parameter setpoints; press , along with and

to change the parameters.

SECTION 3. OPERATION

3-1 303

Model CBC/CBR-103,104,105,106,107

Figure 3-1

3 2 1

4 5

303 3-2

3-2. OPERATING CONTROLS

(Continued)

Model CBC/CBR-103,104,105,106,107

3-3. BASIC OPERATION 1. Turn power switch to ON position.

2. Wait for temperature to reach operating temperature,

36 to 38° F (2.2 to 3.3° C).

3. Place chilled, prepackaged product into case.

Do not stock product in the case beyond the load height

limit of 9 inches (23 cm), or over the front edge. Prod-

uct temperatures may become unsafe, and increase

operating costs.

Do not use mechanical devices or other means to quicken

the defrosting process, other than those recommended by

the manufacturer, or damage to the unit could result.

Do not use electrical appliances inside the food storage

areas of the unit, unless they are of the type recommended

by the manufacturer, or damage to the unit could result.

3-4. CLEANING Weekly:

1. Remove all electrical power supplied to the unit by unplug-

ging the power cord from the wall, or by turning off the

wall circuit breaker.

2. Clean interior and exterior surfaces with a soft cloth, soap and

water.

Do not use steel wool, other abrasive cleaners or

cleaners/sanitizers containing chlorine, bromine, iodine

or ammonia chemicals, as these will deteriorate the

stainless steel, and glass material, and shorten the life of

the unit.

Do not use a water jet (pressure sprayer) to clean the

unit, or component failure could result.

3. Clean around the electronic controls with a soft, damp cloth.

4. Reconnect the electrical power to the unit and unit is now

ready for operation.

3-3 303

Model CBC/CBR-103,104,105,106,107

3-4. CLEANING Every 3 Months:

(Continued) 1. Remove all electrical power supplied to the unit by unplug-

ging the power cord from the wall, or by turning off the

wall circuit breaker.

2. Remove all product from the unit.

3. Remove the riser and trays from the unit and clean with

soap and water at a sink.

4. Clean interior surfaces with a soft cloth, soap and water.

Do not use steel wool, other abrasive cleaners or

cleaners/sanitizers containing chlorine, bromine, iodine

or ammonia chemicals, as these will deteriorate the

stainless steel, and glass material, and shorten the life of

the unit.

Do not use a water jet (pressure sprayer) to clean the

unit, or component failure could result.

5. Clean around light fixtures with a soft, damp cloth.

6. Reconnect the electrical power to the unit and unit is now

ready for operation.

If the power cord is damaged, have a qualified service

technician replace it to prevent electrical shock or

property damage.

303 3-4

Model CBC/CBR-103,104,105,106,107

3-5. PROGRAMMING 1. Press and hold for 4 seconds. The “DEF/SET” light

flashes in display.

Temperature Setpoint

2. Press the or to change the temperature setpoint,

within 5 seconds. After 5 seconds, the last entered setpoint

stays in memory.

Other Parameters

3. Press to access the other parameters. Each press of the

accesses the next parameter. The parameters are:

d: (differential) (-15...15 range)

LS: lower set; lower user-access setpoint limit

(-55...99 range)

The units are programmed to defrost 3 times a day, at 8

hour intervals, lasting 30 minutes. Do not program the

setpoint temperature below 33° F (1° C), or ice build-up

will decrease efficiency.

HS: (higher set) upper user-access setpoint limit

(-55...99 range)

CA: (calibration) temperature readout offset to allow for

possible error due to probe location. (-15...15 range)

rP: (relay protection) elect relay status in case of probe defect.

“on” = compressor ON in case of probe defect

“of” = compressor OFF in case of probe defect

PS: (protection system-short cycle) select type of compressor

protection desired (the actual time delay is set with the next

parameter):

“0”=delay before start - in seconds

“1”=delay before start - in minutes

“2”=delay after stop - in minutes

“3”=delay between starts - in minutes

Pt: (protection time) select the time delay setting for compres-

sor protection. (0...31 range)

3-5 303

Model CBC/CBR-103,104,105,106,107

3-5. PROGRAMMING dS: (defrost system (computation)) dF=digifrost feature;

Continued defrost start time based on total compressor running time.

rt=real time; defrost start frequency, based on real time

dI: (defrost interval) defrost frequency in hours, based on the

selection of “dS”

dE: (defrost endurance) total (maximum) length of a defrost

cycle, expressed in minutes. (1...99 range)

dL: (display lock) temperature display is locked during a

defrost cycle. (0...31 range)

“n”=no (readout continues to display the actual tempera-

ture, even during a defrost cycle

“y”=yes (readout is locked)

dr: (display read-out) select the type of visualization in case of

temperature display lock during defrost (see prameter dL)

“C”=the temperature displayed at the start of a defrost is

locked and does not change during this cycle

“dF”=during the defrost “dF” is displayed

do: (defrost at power on) selects whether or not, the system

goes through the defrost cycle at start-up (or after power

failure)

“n”=no

“y”=yes

dd: (defrost delay at power on) delay of defrost cycle, in

minutes. (0...99 range)

Error Code “E1”

This is the only error code in these controls. It indicates a tempera-

ture sensor failure, such as, a shorted sensor, a sensor break, or

absence of sensor.

It can also indicate an under-range in the system temperature (-55).

In case of an over-range in the system temperature, “99” shows first

in the display, followed by “E1”.

303 3-6

Model CBC/CBR-103,104,105,106,107

3-7 303

DIAGRAM FOR CBC MODEL

Model CBC/CBR-103,104,105,106,107

DIAGRAM FOR CBR MODEL

303 3-8

Model CBC/CBR-103,104,105,106,107

230V-50Hz-1ph-CE

3-9 303

Page is loading ...

Henny Penny CBC/CBR-107 User manual

Brand: Henny Penny

Model: CBC/CBR-107

Category: Deep fryers

Type: User manual

Download PDF

report

Henny Penny CBC/CBR-107 User manual

Henny Penny CBC/CBR-107 User manual

Related papers

Other documents