Hampton Bay EHD82620-1L3-BN Operating instructions
- Type
- Operating instructions
THANK YOU
We appreciate the trust and condence you have placed in Hampton Bay through the purchase of this lighting xture. We strive to continually
create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement
needs. Thank you for choosing Hampton Bay!
USE AND CARE GUIDE
KENDALL MANOR 3-LIGHT BRUSHED NICKEL LINEAR CHANDELIER
WITH CLEAR GLASS SHADES
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday.
1-855-HD-HAMPTON
HAMPTONBAY.COM
Item #1006351603
Model #EHD82620-1L3-BN
2
Table of Contents
Safety Information ..................................2
Warranty ..........................................2
What is covered ...................................2
What is not covered ................................2
Pre-Installation .....................................3
Planning Installation ...............................3
Tools Required .................................... 3
Hardware Included .................................3
Pre-Installation .....................................4
Package Contents .................................4
Installation ........................................5
Maintenance .......................................8
Care and Cleaning ..................................8
Troubleshooting ....................................8
Safety Information
IMPORTANT: Read and understand this entire
manual before you attempt to assemble, install, or
operate this product.
WARNING: Turn off the electricity at the main
circuit breaker panel before you begin this
installation.
WARNING: This product contains chemicals known
to the State of California to cause cancer, birth
defects, and/or other reproductive harm. Thoroughly
wash hands after installing, handling, cleaning, or
otherwise touching this product.
WARNING: This product must be installed in
accordance with the applicable installation code
by a person familiar with the construction and
operation of the product and the hazards involved.
Warranty
WHAT IS COVERED
The manufacturer warrants the lighting xtures to be free from defects in materials and workmanship for a period of three (3) years
from the date of purchase. This warranty applies only to the original consumer and only to products used in normal use and service. If
this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the
product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modications,
alterations, neglect, or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance
with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse,
abuse, negligence, alteration, or faulty installation or any other failure not relating to faulty material or workmanship. This warranty shall not
apply to the nish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of tness for a particular purpose,
other than the warranty contained herein. The manufacturer specically disclaims any liability and shall not be liable for any consequential
or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.Hamptonbay.com.
3 HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation, make sure all the parts are included using the Hardware Included and Package Contents sections. If any
part is missing or damaged, do not attempt to assemble, install, or operate the product.
NOTE: To avoid damaging this product, place it on a a soft,
non-abrasive surface, such as carpet or cardboard.
TOOLS REQUIRED
Phillips
screwdriver
Safety
glasses
Pliers
Electrical
tape
Wire
stripper
Ladder
HARDWARE INCLUDED
NOTE: Hardware is not shown to actual size.
AA BB CC DD EE
Part Description Quantity
AA Wire nut 3
BB Junction box screw 2
CC
DD
EE
Mounting bracket with xture
mounting screws
Chain
Locking link
1
2
4
4
Pre-Installation (continued)
PACKAGE CONTENTS
A
D
C
B
F
E
Part Description Quantity
A Stem 2
B Fixture Body 1
C Shade 3
D
E
F
Socket ring
Threaded cap
Canopy
3
2
1
5 HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Installation
1 Installing the mounting bracket
IMPORTANT: Disconnect the power at the main fuse box.
□Carefully pull the house wires out of the junction box so
the wires are easily accessible for connection to the xture
wires.
□Position the mounting bracket (CC) so the threaded ends of
the attached xture mounting screws are pointing down.
Pull the house wires through the large center hole in the
mounting bracket (CC).
□Align the small holes in the mounting bracket (CC) with the
holes in the junction box.
□Thread one junction box screw (BB) into each hole in the
mounting bracket (CC) and into each hole in the junction
box. Tighten the junction box screws (BB) to secure the
mounting bracket (CC) to the junction box.
2 Preparing the xture and wires
□On the side of the xture without the xture wires, screw
one stem (A) into the top of the xture body (B).
□Attach one locking link (EE) to the loop at the top of the
stem (A).
□On the side of the xture with the xture wires, push
the xture wires up through the bottom of one stem (A).
Carefully pull the xture wires out of the top of the stem (A).
Screw the stem (A) onto the top of the xture body (B).
□Attach one locking link (EE) to the loop at the top of the
stem (A).
□Determine the desired height of the hanging xture. If
needed, remove chain links from each length of chain (DD)
to achieve the desired height. Make sure the chains (EE)
are the same length.
□On the side of the xture without the xture wires, attach
the last chain link on the chain (DD) to the locking link (EE)
on the loop at the top of the stem (A).
□On the side of the xture with the xture wires, attach the
last chain link on the chain (DD) to the locking link (EE) on
the loop at the top of the stem (A).
BB
CC
JUNCTION
BOX
A
B
EE
DD
DD
A
EE
6
Installation (continued)
3 Preparing the xture and wires
(continued)
□On the side of the xture with the xture wires, weave the
xture wires through the chain (DD), skipping every other
chain link.
□Carefully push the xture wires through the loop on the
canopy (F) and up through the hole in the canopy (F).
□On the side of the xture without the wires, attach the
locking link (EE) to the last chain link at the end of the
chain (DD), and then to the loop on the canopy (F).
□On the side of the xture with the xture wires, attach
the locking link (EE) to the last chain link at the end of the
chain (DD), and then to the loop on the canopy (F).
4 Connecting the wires
□Strip 3/4 in. of the insulation from the ends of the xture
wires.
□Loosen the ground screw on the mounting bracket (CC).
Wrap the house ground wire (copper) around the ground
screw on the mounting bracket (CC). Leave enough ground
wire to attach to the xture ground wire. Twist the end of
the xture ground wire and the end of the house ground
wire together. Twist a wire nut (AA) onto the ends of the
wires. Completely tighten the wire nut (AA) to secure the
wires together. Reference the chart below for the correct
wire connections.
B
EE
DD
F
EE
DD
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
AA
CC
HOUSE GROUND
WIRE (COPPER)
FIXTURE
GROUND WIRE
GROUND
SCREW
7 HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Installation (continued)
5 Connecting the wires (continued)
□Twist the end of the house lead wire (black) and the end of
the xture lead wire together. Twist a wire nut (AA) onto the
ends of the wires. Completely tighten the wire nut (AA) to
secure the wires together.
□Twist the end of the house neutral wire (white) and the end
of the xture neutral wire together. Twist a wire nut (AA)
onto the ends of the wires. Completely tighten the wire
nut (AA) to secure the wires together. Reference the chart
below for the correct wire connections.
□Wrap electrical tape (not included) around the wire nuts (AA)
and the wires. Ensure the wires are securely fastened into
the wire nuts (AA).
□Carefully push all the wires and the wire nuts (AA) into the
junction box.
6 Installing the xture to the ceiling
and installing the shades and bulbs
□Raise the xture up to the ceiling. Place the canopy (F)
over the mounting bracket (CC). Pass the holes in the
canopy (F) over the ends of the xture mounting screws
on the mounting bracket (CC). Screw one threaded cap (E)
onto the end of each xture mounting screw. Tighten the
threaded caps (E) to secure the xture to the ceiling.
□Lower one shade (C) over the socket. Pass the hole in the
bottom of the shade (C) down over the socket.
□Screw a socket ring (D) onto the socket. DO NOT over
tighten the socket ring (D).
□Repeat the above steps to install the remaining shades (C).
□Screw the recommended bulbs (E26 Edison bulb type, not
included) into the sockets. The correct bulb wattage is
marked on the socket. DO NOT exceed the maximum bulb
wattage.
FIXTURE
MOUNTING SCREW
E
CC
BULB
(NOT INCLUDED)
DC
SOCKET
F
Connect Black Lead
Supply (House) Wire to:
Connect White Neutral
Supply (House) Wire to:
Black Wire or,
*Parallel Cord
(Round and Smooth) or,
Insulated Wire
(other than green)
with Copper Conductor.
White Wire or,
*Parallel Cord
(Square and Ridged) or,
Insulated Wire
(other than green)
with Silver Conductor.
*When parallel wire (SPT 1 & SPT 2) is used:
The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.
No printed words on
wire insulation or,
Printed words on
wire insulation or,
FIXTURE LEAD WIRE HOUSE LEAD WIRE
(BLACK)
FIXTURE GROUND
WIRE
HOUSE GROUND
WIRE (COPPER)
FIXTURE NEUTRAL
WIRE HOUSE NEUTRAL WIRE
(WHITE)
8
Maintenance
WARNING: Before you perform any cleaning or
maintenance work, turn off the electricity at the main
circuit breaker panel.
Care and Cleaning
□Wipe the xture with a dry, soft cloth.
□Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
Problem Possible Cause Solution
The light bulb will not turn on. A bulb is burned out.
The power is off.
There is a faulty wire connection.
There is a faulty switch.
□Replace the light bulb.
□Ensure the power supply is on.
□Check the wiring.
□Contact a qualied and licensed
electrician if you are not
comfortable troubleshooting wiring
problems.
□Test or replace the switch.
The fuse blows or the circuit breaker trips
when the light is turned on.
There are crossed wires or the power wire is
grounding out.
□Discontinue use of the xture.
Check the wire connections or
contact a qualied electrician.
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday.
1-855-HD-HAMPTON
HAMPTONBAY.COM
Retain this manual for future use.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Hampton Bay EHD82620-1L3-BN Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hampton Bay RS2204145 User guide
-
Hampton Bay T-V00130007B 3 Light Bathroom Vanity Light User guide
-
Hampton Bay 51130T BK User guide
-
Hampton Bay W190427-1SS User guide
-
Hampton Bay 4183 RT User guide
-
Hampton Bay HDP12069BN User guide
-
Hampton Bay 16657 Installation guide
-
Hampton Bay 15670 Operating instructions
-
Hampton Bay 14707 Operating instructions
-
Hampton Bay 14708 Operating instructions
