Ercol 1360 Assembly Instructions

Brand
Ercol
Model
1360
Type
Assembly Instructions

This manual is also suitable for

Thank you for purchasing this Bosco bed. Please ensure instructions are read in full before attempting to
assemble this product.
Pre-assembly preparation
This is a two person operation
This product is heavy, it should be assembled as near as possible to the point of use. Take care when lifting to
avoid personal injury and (or) damage to the product.
Installation should be carried out exactly according to the manufacturers instructions, otherwise a safety
risk can occur if incorrectly installed. Cabinets and shelving over 600mm high can be unstable and should be
1360 & 1361 BOSCO
DOUBLE/KINGSIZE BED
Items you will need
Ref: 00329 / 1360 & 1361 Bosco double / kingsize bed 1
A1 x headboard
B1 x footboard
C2 x side rails
D1 x centre rail
E32 x slats double bed
34 x slats king size
F64 x ends for slats (double)
68 x ends for slats (king)
General assembly
Fittings and parts checklist
2
G8 x threads
H8 x half moon washer
I1 x spanner
J2 x central brackets
K2 x washers
L2 x nuts and bolts
M12 x 25mm screws
Ref: 00329 / 1360 & 1361 Bosco double / kingsize bed
A
D
C
E
E
CB
1. Push the threads (G) into the headboard and the footboard as shown below. Tighten the threads by hand
ensuring that there is approximately half of the thread still showing. Using the 12 x 25mm screws (M), attach
the two brackets (J) onto the headboard and the footboard using the pre-drilled holes, tighten with a phillips
screwdriver.
2. Ensure the holes in the side rails (C) are facing upwards, and you have the left and right rails (see page 2)
on the correct sides. With another person to hold the siderail, locate these side rails onto the protruding
threads on the headboard and footboard. As you do this, slide a half moon washer onto the thread when it
Repeat with the other 3 corners. When all four corners are in place, fully tighten with the spanner (I). Making
sure the holes in the centre rail are facing upwards, put the centre rail (D) into the two brackets (J). Secure it
in place using the 2 x nuts and 45mm bolts (L), and the 2 washers (K).
Step by step assembly instructions
3
Ref: 00329 / 1360 & 1361 Bosco double / kingsize bed
G
J
M
H
I
K
L
3. Push the plastic cap (F) onto the end of each slat (E). With the peg facing downwards push the slat into the
pre-drilled holes as shown below. Repeat for each of the slats. The bed is then fully assembled.
4
Ref: 00329 / 1360 & 1361 Bosco double / kingsize bed
Slats double bed x 32
Slats king size x 34
Ends for slats double bed x 64
Ends for slats king size bed x 68 F
E
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Ercol Furniture Ltd, Summerleys Road, Princes Risborough, Buckinghamshire. HP27 9PX ercol.com
5
Ref: 00329 / 1360 & 1361 Bosco double / kingsize bed
Wood Furniture
Wood displays different grain patterns depending on which way it is cut - for example, the ‘medullary ray’
which can appear on oak furniture is a mark of good quality timber - these are characteristics of the natural
beauty of the wood. All timber surfaces will change colour and mellow over time. New furniture will initially
vary in shade from items that have been previously purchased.
How to care for your wood furniture
Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth. Spillages should
be wiped up as soon as possible. Spray polishes should be avoided as they can contain silicones which may
spoil the furniture’s surface by building up over time. Use of cleaning materials containing abrasive compounds,
acidic or caustic reagents and any bleaches containing oxidising reagents should be avoided as prolonged
use may damage the lacquer surface. If sticky marks occur on the surface they can be removed with a dilute
solution of warm soapy water. The area should be rubbed lightly and then completely dried immediately
afterwards, before replacing any mats etc. Our furniture will endure most temperatures in the home but it is
best to avoid placing furniture next to heat sources such as radiators or fires. Be particularly careful with solid
wood as the lack of humidity caused by central heating can cause damage, such as warping.
Safety Instructions
Never drag furniture when moving it, always lift it. Take care when handling or moving the furniture as careless
handling may cause damage or injury. No liability will be accepted for damage or injury caused by incorrectly
installed furniture.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Ercol 1360 Assembly Instructions

Brand
Ercol
Model
1360
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents