Hyundai Ioniq 5 Mudguard Kit Owner's manual

Brand: Hyundai

Model: Ioniq 5 Mudguard Kit

Type: Owner's manual

Genuine Accessories

Electronic Installation Instructions

Part Weight (Gross) FMVSS 110 Compliance Information

1) Read the entire Installation Instructions prior to beginning the installation of the part.

3) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.

4) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.

5) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.

6) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.

Clip Removal Tool

Right-Angle #2

Phillips Screwdriver

0.49

lbs

All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed options

or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load Carrying

Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying capacity in

kilograms or pounds, which is the total weight of all added options and accessories.

Load Label Part Number: NP070 - 09003

Drill Bit 8mm

(5/16")

Drill Bit 3mm

(1/8")

If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a replacement, register the removal of the

old part before registering the new part. Old and new parts will have different barcode data, and the old registration cannot be reused.

Mix a 1 to 1 ratio of water and Isopropyl Alcohol (70%) into a spray bottle.

Basic Required Tools

Glasses

Deburring Tool

Drill Stop

Right-Angle Electric

Drill

Gloves

Rev. Date

Hearing Protection

Mask

Denotes important information to be

reviewed during the step

Denotes specific tools that are necessary to

complete a step

Denotes cautions to be taken to avoid

physical injury or electronic component

damage

Denotes cautions to be taken to avoid

vehicle and component damage

Difficulty stated above reflects the minimum level of

expertise required to install the accessory:

2022~

GIF46 AC100

Vehicle Model:

Ioniq 5

Accessory:

Language

English

10/29/2021

Denotes warnings that may lead to serious

physical injury or vehicle damage

Denotes quality processes to be checked

prior to moving to the next step

Part No.

Instructional Symbols / Definitions

Denotes personal protective equipment (PPEs) that

may be required for a step. Examples of safety

equipment icons noted below:

(B) Dealer Technician

Mudguard Kit

( B )

(A) Customer

Difficulty:

Note:

Model Year

If this is a printed copy of the installation instructions, ensure you have the latest revision by scanning

the QR code or by entering the website address listed below before beginning installation. Use the

latest revision date as noted by “Rev. Date” above.

www.hyundaiaccessories.com/admin_media_uploads/installationSheets/gif46_ac100.pdf

Center Punch

Masking Tape

50/50 Mix Of Isopropyl

Alcohol (70%) &

Water

Clean Towel

Ruler

1.08

Notes to the installer:

Revision Date

10/29/2021

Page 1 of 5

Genuine Accessories

No.

4 8 2

Hardware Kit Total

Plastic Retainer

Front Mudguard LH

Qty

Front Mudguard RH

Description

Kit Overview

Screw

Adhesive Promoter

Hardware Kit Contents

Hardware Bag

Front Mudguard Template

Rear Mudguard RH

Rear Mudguard LH

Revision Date

10/29/2021

Page 2 of 5

Genuine Accessories

Masking Tape

Make sure to push the mudguard upward and inward during the

installation to eliminate any possible gaps.

WARNING! Take precautions when using the drill to help avoid injury or damage to the vehicle.

Caution! Make sure the drill stop is properly set on the drill bits to ensure the drill bits do not make contact with the steel rocker panel behind the garnish trim.

A. Remove the adhesive backing strip from the provided template and place it on the underside of the driver's side front wheel arch garnish trim as shown above.

B. Using a Center Punch, mark the center of the crosshairs on the template as shown.

C. Remove the template and place it in a safe location to be used on the passenger's side front wheel arch garnish trim.

D. Place a Drill Stop 10mm (25/64") back from the tip of a 3mm (1/8") Drill Bit and drill a pilot hole at the center punch mark.

E. Place a Drill Stop 10mm (25/64") back from the tip of a 8mm (5/16") Drill Bit and enlarge the pilot hole.

F. Carefully Deburr the drilled hole. Do NOT enlarge the hole.

G. Repeat this step on the passenger's side front wheel arch garnish trim.

Center Punch, Right-Angle Electric Drill, Drill Stop, 3mm (1/8") Drill Bit, 8mm (5/16") Drill Bit and Deburring Tool

Clip Removal Tool, 50/50 Mix Of Isopropyl Alcohol (70%) & Water

and Clean Towel

A. Align the driver's side front mudguard (LH) as shown ensuring a proper fit.

B. Place pieces of making tape along the upper and rear edges of the mudguard

as shown above.

C. Temporarily remove the mudguard and set aside in a safe location.

WARNING! Ensure all surfaces have fully dried.

NOTE: Fully turn the steering wheel to the left when installing the driver's

side front mudguard (LH) and fully turn the steering wheel to the right when

installing the passenger's side front mudguard (RH).

A. Starting on the driver's side front wheel well area, remove the two (2) plastic

retainers as shown.

B. Discard the removed hardware.

C. Clean the area of the lower fender where the mudguard will be positioned as

shown, using 50/50 mix of Isopropyl alcohol (70%) & water and allow to fully

dry.

Revision Date

10/29/2021

Page 3 of 5

Genuine Accessories

Ruler

Masking Tape

A. Apply one (1) adhesive promoter onto the lower fender in the highlighted area

shown above.

NOTE: The adhesive promoter should not be applied further than 1.2" (30.5mm)

below the lower fender feature line as shown above.

B. Properly discard promoter.

A. Peel away approximately 1" (25mm) of the adhesive tape liner from the

front mudguard (LH), then wrap around as shown above.

B. Using a piece of masking tape, secure the tape liner to the outside surface

as shown above.

Check for any visible gaps. If any gaps exceed 0.5mm, loosen the hardware

and refit the mudguard(s) to the body to decrease or eliminate the gaps.

A. While pushing the mudguard upward and inward as shown, insert

two (2) provided plastic retainers as shown. Make sure to push in

the center portion of the plastic retainers to lock the retainers in place.

B. Remove and discard the pieces of masking tape.

C. While maintaining proper alignment of the front mudguard (LH) with one

hand, carefully remove the adhesive tape liner in a downward direction.

D. Repeat steps 1-7 for passenger's side front mudguard (RH).

WARNING! Promoter may cause skin irritation if in contact with bare skin.

Ensure gloves are properly worn.

Be careful not to touch or contaminate the exposed surface of the

adhesive tape.

A. Align the mudguard (LH) back into position.

B. While pushing the mudguard upward and inward as shown, insert

one (1) provided plastic retainer into the bottom hole as shown.

Make sure to push in the center portion of the plastic retainer to lock

the retainer in place.

Make sure to push the mudguard upward and inward during the

installation to eliminate any possible gaps.

Revision Date

10/29/2021

Page 4 of 5

Genuine Accessories

A. On the driver's side rear wheel well area, remove the plastic retainer

from the bottom of the vehicle as shown.

B. Remove the two (2) screws as shown.

C. Discard the removed hardware.

Make sure to push the mudguard upward and inward during the

installation to eliminate any possible gaps.

Visual Check

Item to be Checked

A. Align the rear mudguard (LH) as shown ensuring a proper fit.

Make sure to push the mudguard upward and inward during the

installation to eliminate any possible gaps.

Result

A. While pushing the mudguard upward and inward as shown, insert

one (1) provided retainer into the bottom hole as shown. Make sure

to push in the center portion of the plastic retainer to lock the retainer

in place.

Right-Angle #2 Phillips Screwdriver

A. While pushing the mudguard upward and inward as shown, insert and

fasten one (1) provided screw into the upper hole "A" as shown.

B. Insert and fasten one (1) provided screw into the lower hole "B" as shown.

C. Repeat steps 8-11 for the passenger's side rear mudguard (RH).

D. Installation is complete.

Clip Removal Tool and Right-Angle #2 Phillips Screwdriver

Make sure to push the Front and Rear Mudguards upward and inward during the

installation to eliminate any possible gaps.

Check for any visible gaps. If any gaps exceed 0.5mm, loosen the

mounting screws and refit the mudguard(s) to the body to decrease or

eliminate the gaps. Be careful not to over-tighten or strip the screw head.

Front and Rear Mudguards are properly aligned.

Any visible gaps do not exceed 0.5mm.

Check for any visible gaps.

If any gaps exceed 0.5mm, loosen the mounting hardware and refit the

Mudguard(s) to the body to decrease or eliminate the gaps.

Revision Date

10/29/2021

Page 5 of 5

Hyundai Ioniq 5 Mudguard Kit Owner's manual

Hyundai Ioniq 5 Mudguard Kit Owner's manual

Hyundai Ioniq 5 Mudguard Kit Owner's manual

Other documents