Aruba R9F19A Reference guide

HPE FlexFabric 12900E Switch Series

Segment Routing Command Reference

Software

version: Release 5210

Document version: 6W100-20230424

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard

Enterprise products and services are set forth in the express warranty statements accompanying such

products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett

Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or

copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software

Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s

standard commercial license.

Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard

Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise

website.

Acknowledgments

Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the

United States and other countries.

Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.

Java and Oracle are registered trademarks of Oracle and/or its affiliates.

UNIX® is a registered trademark of The Open Group.

i

Contents

SR-MPLS commands ···················································································· 1

bfd detect-multiplier ···································································································································· 1

bfd enable ·················································································································································· 1

bfd min-echo-receive-interval ····················································································································· 2

bfd min-receive-interval ······························································································································ 3

bfd min-transmit-interval ····························································································································· 4

display bgp egress-engineering ipv4 ·········································································································· 5

display bgp egress-engineering peer-set ··································································································· 7

display bgp segment-routing label-range ··································································································· 8

display isis segment-routing adjacency······································································································ 9

display isis segment-routing global-block································································································· 10

display isis segment-routing prefix-sid-map ····························································································· 11

display isis segment-routing routing-table ································································································ 13

display mpls static-sr-mpls adjacency ······································································································ 16

display mpls static-sr-mpls ipv6 adjacency ······························································································ 17

display mpls static-sr-mpls lsp ················································································································· 18

display mpls static-sr-mpls prefix ············································································································· 19

display mpls static-sr-mpls ipv6 prefix ······································································································ 20

display mpls te segment-routing tunnel path ···························································································· 22

display mpls te tunnel lsp-event ··············································································································· 23

display ospf segment-routing adjacency ·································································································· 26

display ospf segment-routing global-block ······························································································· 27

display ospf segment-routing prefix-sid-map ··························································································· 28

display ospf segment-routing routing-table ······························································································ 30

display segment-routing label-block ········································································································· 32

display segment-routing mapping-server prefix-sid-map ········································································· 33

egress-engineering peer-set ···················································································································· 35

fast-reroute microloop-avoidance enable ································································································· 36

fast-reroute microloop-avoidance rib-update-delay·················································································· 37

fast-reroute ti-lfa ······································································································································· 38

global-block ·············································································································································· 40

isis adjacency-sid ····································································································································· 40

isis adjacency-sid weight ·························································································································· 42

isis fast-reroute ti-lfa disable ···················································································································· 43

isis label-conflict-check enable················································································································· 43

isis member-port adjacency-sid ··············································································································· 44

isis prefix-sid ············································································································································ 46

local-block ················································································································································ 47

mapping-server prefix-sid-map ················································································································ 48

mpls te path-selection adjacency-sid ······································································································· 49

mpls te static-sr-mpls ······························································································································· 49

mpls te static-sr-mpls wtr ························································································································· 50

ospf adjacency-sid ··································································································································· 51

ospf adjacency-sid weight ························································································································ 52

ospf fast-reroute ti-lfa disable ··················································································································· 53

ospf prefix-sid ··········································································································································· 54

peer egress-engineering ·························································································································· 55

peer peer-set ············································································································································ 56

sbfd detect-multiplier ································································································································ 57

sbfd enable ··············································································································································· 58

sbfd min-receive-interval ·························································································································· 59

sbfd min-transmit-interval ························································································································· 60

segment-routing ······································································································································· 61

segment-routing adjacency enable ·········································································································· 61

segment-routing global-block ··················································································································· 62

segment-routing lsp-trigger ······················································································································ 63

segment-routing mapping-server advertise-local ····················································································· 63

ii

segment-routing mapping-server receive································································································· 64

segment-routing member-port adjacency enable····················································································· 65

segment-routing microloop-avoidance enable ························································································· 66

segment-routing microloop-avoidance rib-update-delay ·········································································· 67

segment-routing mpls ······························································································································· 68

segment-routing sr-prefer ························································································································· 69

static-sr-mpls adjacency ··························································································································· 70

static-sr-mpls ipv6 adjacency ··················································································································· 71

static-sr-mpls lsp ······································································································································ 72

static-sr-mpls prefix ·································································································································· 73

static-sr-mpls ipv6 prefix ·························································································································· 75

tunnel-bfd detect-multiplier ······················································································································· 76

tunnel-bfd enable ····································································································································· 77

tunnel-bfd min-echo-receive-interval ········································································································ 78

tunnel-bfd min-receive-interval ················································································································· 79

tunnel-bfd min-transmit-interval ················································································································ 79

SR-MPLS TE policy commands ··································································· 81

address-family ipv4 sr-policy ···················································································································· 81

advertise ebgp enable ······························································································································ 81

affinity (SR-TE-ODN dynamic view) ········································································································· 82

affinity (constraints view) ·························································································································· 82

affinity-map ··············································································································································· 83

backup hot-standby ·································································································································· 84

best-effort default ····································································································································· 85

bfd echo ··················································································································································· 86

bfd trigger path-down ······························································································································· 87

binding-sid ················································································································································ 89

candidate-paths ········································································································································ 89

color end-point ········································································································································· 90

color match dscp ······································································································································ 91

constraints ················································································································································ 92

default-color (public instance IPv4/IPv6 address family view) ································································· 93

default-color (VPN instance IPv4/IPv6 unicast address family view) ······················································· 94

delete-delay ·············································································································································· 94

display bgp routing-table ipv4 sr-policy ···································································································· 95

display pce segment-routing policy database ························································································ 103

display pce segment-routing policy initiate-cache ·················································································· 107

display segment-routing te bfd ··············································································································· 108

display segment-routing te database ····································································································· 110

display segment-routing te forwarding ··································································································· 116

display segment-routing te policy ··········································································································· 120

display segment-routing te policy last-down-reason ·············································································· 126

display segment-routing te policy statistics ···························································································· 128

display segment-routing te policy-group ································································································ 130

display segment-routing te sbfd ············································································································· 131

distribute bgp-ls ······································································································································ 133

dynamic (SR-MPLS TE policy path preference view) ············································································ 133

dynamic (SR-TE-ODN view) ·················································································································· 134

end-point ················································································································································ 135

exclude-any ············································································································································ 135

explicit segment-list ································································································································ 136

forwarding statistics ································································································································ 137

forwarding statistics enable ···················································································································· 138

forwarding statistics interval ··················································································································· 139

import-route sr-policy ····························································································································· 139

include-all ··············································································································································· 140

include-any ············································································································································· 141

index ······················································································································································· 141

maximum-sid-depth ································································································································ 142

metric ····················································································································································· 143

name ······················································································································································ 144

iii

name bit-position ···································································································································· 145

on-demand ············································································································································· 146

pce capability segment-routing ·············································································································· 147

pce delegation ········································································································································ 147

pce passive-delegate report-only ··········································································································· 148

pcep (SR-TE-ODN dynamic view) ········································································································· 149

pcep (SR-MPLS TE policy path preference dynamic view) ··································································· 150

policy ······················································································································································ 151

policy-group ············································································································································ 151

preference ·············································································································································· 152

reoptimization ········································································································································· 153

reset segment-routing te forwarding statistics························································································ 154

restrict ···················································································································································· 154

router-id filter ·········································································································································· 155

sbfd ························································································································································ 156

segment-list ············································································································································ 158

segments ················································································································································ 158

service-class ·········································································································································· 159

shutdown ················································································································································ 160

sid-algorithm ··········································································································································· 160

sid-limit ··················································································································································· 161

source-address ······································································································································ 162

sr-policy backup hot-standby enable······································································································ 164

sr-policy bfd echo ··································································································································· 165

sr-policy bfd first-fail-timer ······················································································································ 166

sr-policy bfd trigger path-down enable ··································································································· 167

sr-policy calc-schedule-interval ·············································································································· 168

sr-policy immediate-reoptimization ········································································································· 169

sr-policy log enable ································································································································ 170

sr-policy pce delegation enable·············································································································· 170

sr-policy pce passive-delegate report-only enable ················································································· 171

sr-policy reoptimization ·························································································································· 172

sr-policy sbfd enable ······························································································································ 173

sr-policy sbfd timer ································································································································· 175

sr-policy switch-delay delete-delay ········································································································ 176

sr-policy up-delay ··································································································································· 176

strict-sid-only enable ······························································································································ 177

traffic-engineering ·································································································································· 178

type ························································································································································ 179

up-delay ················································································································································· 180

SRv6 commands ······················································································· 182

advertise srv6 locator ····························································································································· 182

anycast enable ······································································································································· 183

diffserv-mode ········································································································································· 183

display bgp egress-engineering ipv6 ······································································································ 185

display bgp egress-engineering srv6 peer-set ······················································································· 187

display isis segment-routing ipv6 capability ··························································································· 188

display isis segment-routing ipv6 locator ······························································································· 189

display isis segment-routing ipv6 sid-info conflict ·················································································· 192

display isis segment-routing ipv6 sid-info locator ··················································································· 193

display isis segment-routing ipv6 sid-info sid ························································································· 196

display isis segment-routing ipv6 sid-info statistics ················································································ 198

display isis segment-routing ipv6 sid-info system-id ·············································································· 199

display ospfv3 segment-routing ipv6 capability ······················································································ 201

display ospfv3 segment-routing ipv6 locator ·························································································· 202

display segment-routing ipv6 available-static-sid ··················································································· 203

display segment-routing ipv6 brief ········································································································· 205

display segment-routing ipv6 forwarding································································································ 205

display segment-routing ipv6 local-sid ··································································································· 207

display segment-routing ipv6 local-sid forwarding statistics··································································· 212

display segment-routing ipv6 local-sid statistics ···················································································· 214

iv

display segment-routing ipv6 locator······································································································ 216

display segment-routing ipv6 locator-statistics······················································································· 218

egress-engineering srv6 peer-set ·········································································································· 219

encapsulation source-address ··············································································································· 220

fast-reroute microloop-avoidance enable ······························································································· 221

fast-reroute microloop-avoidance rib-update-delay················································································ 222

fast-reroute ti-lfa ····································································································································· 223

flavor-mode switch no-psp ····················································································································· 224

isis ipv6 fast-reroute ti-lfa disable ··········································································································· 225

locator ···················································································································································· 226

local-sid forwarding statistics enable······································································································ 227

local-sid forwarding statistics interval ····································································································· 228

opcode ··················································································································································· 229

ospfv3 fast-reroute ti-lfa disable ············································································································· 232

path-mtu ················································································································································· 232

path-mtu reserved ·································································································································· 233

peer egress-engineering srv6 ················································································································ 234

peer peer-set ·········································································································································· 235

reset segment-routing ipv6 local-sid forwarding statistics ······································································ 236

segment-routing ipv6 (system view) ······································································································· 237

segment-routing ipv6 advertise l3-service-sid ························································································ 237

segment-routing ipv6 egress-engineering locator ·················································································· 238

segment-routing ipv6 end-x delete-delay ······························································································· 239

segment-routing ipv6 locator (IS-IS IPv6 address family view) ······························································ 240

segment-routing ipv6 locator (OSPFv3 process view) ··········································································· 241

segment-routing microloop-avoidance enable ······················································································· 242

segment-routing microloop-avoidance rib-update-delay ········································································ 243

srh-mode switch normal ························································································································· 244

SRv6 TE policy commands ········································································ 246

address-family ipv6 sr-policy ·················································································································· 246

advertise ebgp enable ···························································································································· 246

autoroute enable ···································································································································· 247

autoroute metric ····································································································································· 248

backup hot-standby ································································································································ 248

best-effort default ··································································································································· 249

bestroute encap-type ····························································································································· 250

bfd echo ················································································································································· 252

bfd srv6-encapsulation-mode ················································································································· 253

bfd trigger path-down ····························································································································· 254

binding-sid ·············································································································································· 256

bypass enable ········································································································································ 257

candidate-paths ······································································································································ 257

color end-point ······································································································································· 258

color match dscp (SRv6 TE Policy group view) ····················································································· 259

default-color (public instance IPv4/IPv6 address family view) ······························································· 260

default-color (VPN instance IPv4/IPv6 address family view) ································································· 261

delete-delay ············································································································································ 261

display bgp mirror remote-sid ················································································································· 262

display bgp routing-table ipv6 sr-policy ·································································································· 263

display evpn srv6 mirror remote-sid ······································································································· 272

display pce segment-routing ipv6 policy database ················································································· 273

display pce segment-routing ipv6 policy initiate-cache ·········································································· 276

display segment-routing ipv6 te database······························································································ 278

display segment-routing ipv6 te bfd ······································································································· 286

display segment-routing ipv6 te forwarding···························································································· 287

display segment-routing ipv6 te policy ··································································································· 291

display segment-routing ipv6 te policy last-down-reason······································································· 298

display segment-routing ipv6 te policy statistics ···················································································· 299

display segment-routing ipv6 te policy status························································································· 301

display segment-routing ipv6 te policy-group ························································································· 303

display segment-routing ipv6 te policy-group last-down-reason ···························································· 305

v

display segment-routing ipv6 te policy-group statistics ·········································································· 306

display segment-routing ipv6 te sbfd······································································································ 307

display segment-routing ipv6 te segment-list ························································································· 308

display segment-routing ipv6 te source-sid ···························································································· 310

distribute bgp-ls ······································································································································ 311

drop-upon-invalid ··································································································································· 312

dynamic (SRv6 TE policy path preference view) ··················································································· 313

dynamic (SRv6-TE-ODN view) ·············································································································· 314

encapsulation-mode encaps include local-end.x ··················································································· 314

end-point ················································································································································ 315

explicit segment-list ································································································································ 316

fast-reroute mirror delete-delay ·············································································································· 317

fast-reroute mirror enable ······················································································································· 318

forwarding ignore-last-sid ······················································································································· 319

forwarding statistics ································································································································ 320

group-color ············································································································································· 321

import-route sr-policy ····························································································································· 321

index ······················································································································································· 322

mirror remote-sid delete-delay ··············································································································· 323

on-demand ············································································································································· 324

path verification ······································································································································ 325

pce capability segment-routing ipv6 ······································································································· 326

pce delegation ········································································································································ 327

pce passive-delegate report-only ··········································································································· 328

pcep (SRv6 TE policy path preference dynamic view) ··········································································· 329

policy ······················································································································································ 330

policy-group ············································································································································ 330

preference ·············································································································································· 331

reset segment-routing ipv6 te forwarding statistics ················································································ 332

restrict ···················································································································································· 332

router-id filter ·········································································································································· 333

sbfd ························································································································································ 334

segment-list ············································································································································ 336

service-class ·········································································································································· 336

shutdown ················································································································································ 337

snmp-agent trap enable srv6-policy ······································································································· 338

source-address ······································································································································ 338

sr-policy steering ···································································································································· 340

sr-te frr enable ········································································································································ 341

srv6-policy alarm-threshold ···················································································································· 342

srv6-policy autoroute enable ·················································································································· 343

srv6-policy backup hot-standby enable ·································································································· 344

srv6-policy bfd echo ······························································································································· 345

srv6-policy bfd first-fail-timer ·················································································································· 346

srv6-policy bfd trigger path-down enable ······························································································· 347

srv6-policy drop-upon-invalid enable ····································································································· 348

srv6-policy encapsulation-mode encaps include local-end.x ································································· 349

srv6-policy forwarding ignore-last-sid ····································································································· 350

srv6-policy forwarding statistics enable ·································································································· 351

srv6-policy forwarding statistics interval ································································································· 351

srv6-policy locator ·································································································································· 352

srv6-policy log enable ···························································································································· 353

srv6-policy path verification enable ········································································································ 354

srv6-policy pce delegation enable ·········································································································· 355

srv6-policy pce passive-delegate report-only enable ············································································· 356

srv6-policy sbfd ······································································································································ 357

srv6-policy switch-delay delete-delay····································································································· 358

srv6-policy up-delay ······························································································································· 359

traffic-engineering ·································································································································· 360

up-delay ················································································································································· 360

vi

SRv6 VPN commands ··············································································· 362

default color ············································································································································ 362

display l2vpn forwarding srv6 ················································································································· 362

display l2vpn peer srv6 ·························································································································· 365

display l2vpn vsi ····································································································································· 371

display l2vpn xconnect-group ················································································································· 375

evpn encapsulation srv6 ························································································································ 378

evpn encapsulation srv6 binding instance ····························································································· 378

locator-sbfd enable ································································································································· 379

nexthop interface (BGP IPv4 SR next hop view/BGP-VPN IPv4 SR next hop view/BGP-VPN IPv4 EVPN

SR next hop view) ·································································································································· 380

nexthop interface (BGP SRv6 next hop view/BGP-VPN SRv6 next hop view/BGP-VPN IPv6 EVPN SR

next hop view) ········································································································································ 382

peer advertise encap-type srv6 ·············································································································· 383

peer prefix-sid ········································································································································ 384

peer srv6-vpn compatible ······················································································································· 385

ping evpn vpls srv6 ································································································································ 386

ping evpn vpws srv6 ······························································································································· 388

segment-routing ipv6 ······························································································································ 390

segment-routing ipv6 apply-sid all-nexthop (BGP IPv4/IPv6 address family view) ································ 391

segment-routing ipv6 apply-sid all-nexthop (BGP-VPN IPv4/IPv6 address family view) ······················· 392

segment-routing ipv6 apply-sid specify-nexthop (BGP IPv4/IPv6 address family view) ························ 393

segment-routing ipv6 apply-sid specify-nexthop (BGP-VPN IPv4/IPv6 address family view)················ 394

segment-routing ipv6 best-effort ············································································································ 396

segment-routing ipv6 locator ·················································································································· 397

segment-routing ipv6 locator (cross-connect view, EVPN instance view, and VSI EVPN instance view)

······························································································································································· 398

segment-routing ipv6 locator anycast ···································································································· 400

segment-routing ipv6 traffic-engineering ································································································ 402

srv6-pw-type ··········································································································································· 403

tracert evpn vpls srv6 ····························································································································· 405

tracert evpn vpws srv6 ··························································································································· 406

unicast-forwarding dx2-based ················································································································ 408

SRv6 OAM commands ·············································································· 410

ping ipv6-sid ··········································································································································· 410

ping srv6-te policy ·································································································································· 413

remote end-op ········································································································································ 415

tracert ipv6-sid ········································································································································ 416

tracert srv6-te policy ······························································································································· 418

Document conventions and icons ······························································ 422

Conventions ··················································································································································· 422

Network topology icons ·································································································································· 423

Support and other resources ····································································· 424

Accessing Hewlett Packard Enterprise Support····························································································· 424

Accessing updates ········································································································································· 424

Websites ················································································································································ 425

Customer self repair ······························································································································· 425

Remote support ······································································································································ 425

Documentation feedback ······················································································································· 425

Index ·········································································································· 427

1

SR-MPLS commands

bfd detect-multiplier

Use bfd detect-multiplier to set the BFD detection time multiplier for SRLSPs.

Use undo bfd detect-multiplier to restore the default.

Syntax

bfd detect-multiplier value

undo bfd detect-multiplier

Default

The BFD detection time multiplier is not set for SRLSPs. The BFD detection time multiplier set by the

bfd multi-hop detect-multiplier command applies.

Views

Segment Routing view

Predefined user roles

network-admin

Parameters

value: Specifies a detection time multiplier, which is the maximum number of consecutive BFD

packets that can be discarded. The value range for this argument is 3 to 50.

Usage guidelines

The device sends BFD packets to a peer periodically. If the device does not receive BFD packets

from the peer within the actual detection interval, it determines that the session is down. The actual

detection interval of the sender is the detection time multiplier of the receiver × the actual sending

interval of the receiver.

This command takes effect only on BFD sessions created by the bfd enable command.

Examples

# Set the BFD detection time multiplier to 3 for SRLSPs.

<Sysname> system-view

[Sysname] segment-routing

[Sysname-segment-routing] bfd detect-multiplier 3

Related commands

bfd enable

bfd multi-hop detect-multiplier (High Availability Command Reference)

bfd enable

Use bfd enable to enable BFD for SRLSPs.

Use undo bfd enable to restore the default.

Syntax

bfd enable [ prefix-list prefix-list-name ] [ echo | nil-fec ]

2

undo bfd enable

Default

BFD for SRLSPs is not enabled.

Views

Segment routing view

Predefined user roles

network-admin

Parameters

prefix-list prefix-list-name: Specifies an IPv4 prefix list by the prefix list name, a

case-sensitive string of 1 to 63 characters. The device can create BFD sessions only for the SRLSPs

permitted by the specified IPv4 prefix list. If you do not specify an IPv4 prefix list, the device can

create BFD sessions for all SRLSPs.

echo: Specifies the BFD echo packet mode. If you do not specify this keyword, the BFD control

packet mode is used to verify SRLSP connectivity.

nil-fec: Encapsulates the Nil FEC in MPLS echo request packets when BFD control packet mode

is used to detect SRLSPs. In SR to LDP interworking mode, the ingress node (source node) cannot

determine whether the LDP LSP is connected to the SRLSP. When the ingress node uses MPLS

BFD to detect LSPs, it encapsulates LDP FEC in MPLS echo request packets, which will fail the FEC

type verification on the egress node (end-point node). Then, the BFD session will go down. To

resolve this issue, specify the nil-fec keyword to enable the ingress node to encapsulate the Nil

FEC in MPLS echo request packets. The egress node will not check the FEC type of packets

encapsulated with the Nil FEC.

Usage guidelines

This command enables the device to create a BFD session for each primary SRLSP to verify the

connectivity of the primary SRLSP. When a primary SRLSP fails, BFD can quickly detect the failure

and switches traffic to the backup SRLSP to reduce packet loss.

Before you execute this command, enable MPLS BFD by using the mpls bfd enable command.

If you execute both the bfd enable command and the mpls bfd command for SRLSPs, the mpls

bfd command takes effect on the SRLSPs.

Examples

# Enable BFD for SRLSPs.

<Sysname> system-view

[Sysname] segment-routing

[Sysname-segment-routing] bfd enable

Related commands

mpls bfd (for LSP) (MPLS Command Reference)

mpls bfd enable (MPLS Command Reference)

bfd min-echo-receive-interval

Use bfd min-echo-receive-interval to set the minimum interval for receiving BFD echo

packets for SRLSP BFD.

Use undo bfd min-echo-receive-interval to restore the default.

3

Syntax

bfd min-echo-receive-interval interval

undo bfd min-echo-receive-interval

Default

The minimum interval for receiving BFD echo packets is not set for SRLSP BFD. The interval set by

the bfd multi-hop min-echo-receive-interval command applies.

Views

Segment routing view

Predefined user roles

network-admin

Parameters

interval: Specifies the minimum interval for receiving BFD echo packets, in milliseconds. The

value range for this argument is 3 to 10000.

Usage guidelines

The interval for receiving BFD echo packets is also the interval for sending BFD echo packets. By

executing this command, you can control both the receiving interval and sending interval for BFD

echo packets.

This command takes effect only on the echo mode BFD sessions created by the bfd enable

command.

Examples

# Set the minimum BFD echo packet receiving interval for SRLSP BFD to 450 milliseconds.

<Sysname> system-view

[Sysname] segment-routing

[Sysname-segment-routing] bfd min-echo-receive-interval 450

Related commands

bfd enable

bfd multi-hop min-echo-receive-interval (High Availability Command Reference)

bfd min-receive-interval

Use bfd min-receive-interval to set the minimum BFD packet receiving interval for SRLSP

BFD.

Use undo bfd min-receive-interval to restore the default.

Syntax

bfd min-receive-interval interval

undo bfd min-receive-interval

Default

The minimum interval for receiving BFD packets is not set for SRLSP BFD. The interval set by the

bfd multi-hop min-receive-interval command applies.

Views

Segment routing view

4

Predefined user roles

network-admin

Parameters

interval: Specifies the minimum interval for receiving BFD packets, in milliseconds. The value

range for this argument is 3 to 10000.

Usage guidelines

Use this command to prevent the packet sending rate of the peer end from exceeding the packet

receiving rate of the local end. If the receiving rate is exceeded, the peer end dynamically adjusts the

BFD packet transmitting interval to the minimum receiving interval of the local end.

This command takes effect only on BFD sessions created by the bfd enable command.

Examples

# Set the minimum BFD packet receiving interval for SRLSP BFD to 550 milliseconds.

<Sysname> system-view

[Sysname] segment-routing

[Sysname-segment-routing] bfd min-receive-interval 550

Related commands

bfd enable

bfd multi-hop min-receive-interval (High Availability Command Reference)

bfd min-transmit-interval

Use bfd min-transmit-interval to set the minimum BFD packet transmitting interval for

SRLSP BFD.

Use undo bfd min-transmit-interval to restore the default.

Syntax

bfd min-transmit-interval interval

undo bfd min-transmit-interval

Default

The minimum interval for transmitting BFD packets is not set for SRLSP BFD. The interval set by the

bfd multi-hop min-transmit-interval command applies.

Views

Segment routing view

Predefined user roles

network-admin

Parameters

interval: Specifies the minimum interval for transmitting BFD packets, in milliseconds. The value

range is 3 to 10000.

Usage guidelines

Use this command to prevent the BFD packet sending rate from exceeding the packet receiving rate

of the peer end.

The actual BFD packet transmitting interval on the local end is the greater value between the

following values:

5

•

Minimum interval for transmitting BFD packets on the local end.

•

Minimum interval for receiving BFD packets on the peer end.

This command takes effect only on BFD sessions created by the bfd enable command.

Examples

# Set the minimum BFD packet transmitting interval for SRLSP BFD to 450 milliseconds.

<Sysname> system-view

[Sysname] segment-routing

[Sysname-segment-routing] bfd min-transmit-interval 450

Related commands

bfd enable

bfd multi-hop min-transmit-interval (High Availability Command Reference)

display bgp egress-engineering ipv4

Use display bgp egress-engineering ipv4 to display BGP EPE information.

Syntax

display bgp [ instance instance-name ] egress-engineering ipv4

[ ipv4-address ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

instance instance-name: Specifies a BGP instance by its name, a case-sensitive string of 1 to

31 characters. If you do not specify this option, the command displays information about the default

BGP instance.

ipv4-address: Specifies the IPv4 address of an existing peer. If you do not specify this argument,

the command displays information about all peers and peer groups.

verbose: Displays detailed BGP EPE information. If you do not specify this keyword, the command

displays brief BGP EPE information.

Examples

# Display brief BGP EPE information.

<Sysname> display bgp egress-engineering ipv4

PeerSet : 192.168.1.2

Local AS number : 1

Remote AS number : 2

Local router ID : 1.1.1.3

Remote router ID : 1.1.1.4

OriginNextHop : 192.168.1.2

RelyNextHop : 192.168.1.2

Interface : HGE1/0/1

# Display brief BGP EPE information for a peer.

6

<Sysname> display bgp egress-engineering ipv4 192.168.1.5

BGP peering segment type: Node-Adjacency

PeerNodeAdj : 192.168.1.5

Local AS number : 1

Remote AS number : 2

Local router ID : 1.1.1.3

Remote router ID : 1.1.1.5

OriginalNextHop : 192.168.1.5

RelayNextHop : 192.168.1.5

Interface : HGE1/0/5

# Display detailed BGP EPE information for a peer.

<Sysname> display bgp egress-engineering ipv4 1.1.1.1 verbose

BGP peering segment type : Node

PeerAdj Num : 2

PeerNode : 1.1.1.1

Local AS number : 1

Remote As number : 2

Local router ID : 1.1.1.3

Remote router ID : 1.1.1.4

Local interface address : 2.2.2.2

Remote interface address : 1.1.1.1

OriginalNextHop : 1.1.1.1

RelayNextHop : 100.0.27.7

OriginalNextHop : 1.1.1.1

RelayNextHop : 100.0.28.7

Label : 15000

TunnelPolicy : abc

BGP peering segment type : Adjacency

PeerAdj : 100.0.27.7

Local AS number : 1

Remote AS number : 2

Local router ID : 1.1.1.1

Remote router ID : 2.2.2.2

OriginalNextHop : 100.0.27.7

RelayNextHop : 100.0.27.7

Local interface address : 100.0.27.2

Remote interface address : 100.0.27.7

Interface : GE1/0/1

Label : 24001

TunnelPolicy : abc

BGP peering segment type : Adjacency

PeerAdj : 100.0.28.7

Local AS number : 1

Remote AS number : 2

Local router ID : 1.1.1.1

Remote router ID : 2.2.2.2

OriginalNextHop : 100.0.28.7

RelayNextHop : 100.0.28.7

7

Local interface address : 100.0.28.2

Remote interface address : 100.0.28.7

Interface : GE1/0/2

Label : 24002

TunnelPolicy : abc

Table 1 Command output

Field

Description

BGP peering segment type

Type of the BGP peering segments to the specified peer:

• Node.

• Adjacency.

• Set.

• Node-Adjacency.

PeerAdj Num Number of peering adjacencies.

Interface Interface on which the neighborship is established.

OriginalNextHop Original next hop.

RelayNextHop Recursive next hop.

display bgp egress-engineering peer-set

Use display bgp egress-engineering peer-set to display BGP EPE peer set information.

Syntax

display bgp [ instance instance-name ] egress-engineering peer-set

[ peer-set-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

instance instance-name: Specifies a BGP instance by its name, a case-sensitive string of 1 to

31 characters. If you do not specify a BGP instance, this command displays BGP EPE peer set

information for the default BGP instance.

peer-set-name: Specifies a BGP EPE peer set by its name, a case-sensitive string of 1 to 63

characters. If you do not specify a peer set, this command displays information about all BGP EPE

peer sets.

Examples

# Display information about all BGP EPE peer sets.

<Sysname> display bgp egress-engineering peer-set

BGP egress peering segment peer-set: a

PeerSet label : 2172

Members: 0

8

BGP egress peering segment peer-set: b

PeerSet label : 5555

Members: 1

BGP PeerNodeAdj : 3.3.3.3

BGP egress peering segment peer-set: c

PeerSet label: 65001

Label : 65001

Members: 2

BGP PeerNode: 1.1.1.1

BGP PeerAdj : 10.1.1.1

PeerSet name: d

PeerSet label: 65002

Members: 2

BGP PeerNode: 2.2.2.2

BGP PeerAdj : 11.1.1.1

Table 2 Command output

Field

Description

BGP egress peering segment peer-set Name of a BGP EPE peer set.

PeerSet label SID used by the BGP EPE peer set.

Label SID assigned to the BGP EPE peer set.

Members Number of peers in the BGP EPE peer set.

BGP PeerNode Address of the node peer.

BGP PeerAdj Address of the adjacency peer.

BGP PeerNodeAdj Address of the node-adjacency peer.

display bgp segment-routing label-range

Use display bgp segment-routing label-range to display BGP SR label ranges.

Syntax

display bgp [ instance instance-name ] segment-routing label-range

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

instance instance-name: Specifies a BGP instance by its name, a case-sensitive string of 1 to

31 characters. If you do not specify this option, the command displays information about the default

BGP instance.

9

Examples

# Display BGP SR label ranges.

<Sysname> display bgp segment-routing label-range

BGP peering segment labels:

56000-250000

Prefix labels:

16000-55999

display isis segment-routing adjacency

Use display isis segment-routing adjacency to display IS-IS SR adjacency SID

information.

Syntax

display isis [ process-id ] segment-routing adjacency [ { member-port |

non-member-port } | sid sid-value | vpn-instance vpn-instance-name ] *

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

process-id: Specifies an IS-IS process ID in the range of 1 to 65535. If you do not specify this

argument, the command displays SR adjacency SID information about all IS-IS processes.

member-port: Displays SR adjacency SID information on Layer 3 aggregation group member

interfaces.

non-member-port: Displays SR adjacency SID information on Layer 3 Ethernet interfaces except

aggregation group member interfaces.

sid sid-value: Specifies an adjacency SID value in the range of 15000 to 250000.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a

case-sensitive string of 1 to 31 characters.

Usage guidelines

If you do not specify the member-port or non-member-port keyword, this command displays

SR adjacency SID information on all interfaces.

If you do not specify the sid sid-value option, this command displays information about all IS-IS

SR adjacency SIDs.

If you do not specify the vpn-instance vpn-instance-name option, this command displays

SR adjacency SID information on the public network.

Examples

# Display SR adjacency SID information about IS-IS process 1.

<Sysname> display isis 1 segment-routing adjacency

Adjacency SID: 15020 Type: Non-member-port Request result: Init

SystemID Interface NextHop State ProcessID

10

0000.0000.0000.00 HGE1/0/1 2.2.2.2 Inactive 1

Table 3 Command output

Field

Description

Adjacency SID Adjacency SID value.

Type

Type of the adjacency SID assigned to the adjacency link:

• Member-port—Adjacency SID assigned to a Layer 3

aggregation group member interface.

• Non-member-port—Adjacency SID assigned to a

Layer 3 Ethernet interface that is not an aggregation

group member interface.

Request result

Adjacency SID application result:

• Succeeded—The application succeeded.

• Conflicting—The adjacency SID is already used.

• Init—The application is in progress or the adjacency

SID allocation feature is not enabled.

• Out-of-range—The adjacency SID is not the in the

range of the SRLB.

SystemID System ID of the neighbor.

Interface Interface connected to the neighbor.

Nexthop Next hop of the adjacency SID.

State

SID status:

• Active—The SID is effective and is available for use.

• Inactive—The SID is not effective and is not available

for use.

ProcessID IS-IS process ID.

display isis segment-routing global-block

Use display isis segment-routing global-block to display IS-IS SRGB information.

Syntax

display isis segment-routing global-block [ level-1 | level-2 ]

[ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

level-1: Specifies Level-1 SRGB.

level-2: Specifies Level-2 SRGB.

process-id: Specifies an IS-IS process ID in the range of 1 to 65535. If you do not specify this

argument, the command displays the SRGBs of all IS-IS processes.

11

Usage guidelines

If you do not specify the level-1 or level-2 keyword, the command displays information about

both the Level-1 SRGB and Level-2 SRGB.

Examples

# Display information about the SRGBs for IS-IS process 1.

<Sysname> display isis segment-routing global-block 1

Segment routing global block information for IS-IS(1)

-----------------------------------------------------

Level-1 SRGB

-------------------------

System ID Base Range

-------------------------------------------------------------------------------

0000.0000.0011 16666 5557

0000.0000.0012 18012 4001

Table 4 Command output

Field

Description

System ID System ID of the neighbor.

Base Minimum label value of the SRGB.

Range Number of labels in the SRGB.

Related commands

segment-routing global-block

display isis segment-routing prefix-sid-map

Use display isis segment-routing prefix-sid-map to display IS-IS SR prefix-SID

mappings.

Syntax

display isis segment-routing prefix-sid-map [ active-policy |

backup-policy ] [ process-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

active-policy: Displays active prefix-SID mappings.

backup-policy: Displays backup prefix-SID mappings.

process-id: Specifies an IS-IS process ID in the range of 1 to 65535. If you do not specify this

argument, the command displays information about all IS-IS processes.

12

verbose: Displays detailed information. If you do not specify this keyword, the command displays

brief information.

Usage guidelines

If you do not specify the active-policy or backup-policy keyword, the command displays

information about both active and backup prefix-SID mappings.

Examples

# Display active IS-IS SR prefix-SID mappings.

<Sysname> display isis segment-routing prefix-sid-map active-policy

ISIS 1 - Active policy

Number of mappings: 5

Prefix SID index Range Flags

2.2.2.2/32 10 10 -

3.3.3.3/32 300 1 -

8.8.8.8/32 600 20 -

11.11.11.11/32 100 10 -

12.12.12.1/32 44 3 -

# Display detailed information about active IS-IS SR prefix-SID mappings.

<Sysname> display isis segment-routing prefix-sid-map active-policy verbose

ISIS 1 - Active policy

Number of mappings: 2

Prefix 1.1.1.1 32

Source : Local

Router ID : 1010.1020.1030

Level : Not set

SID index : 100

Range : 1

Last prefix : 1.1.1.1/32

Last SID index: 100

Flags : -

Prefix 2.2.2.2 32

Source : Remote

Router ID : 1010.1020.1040

Level : L1

SID index : 200

Range : 1

Last prefix : 2.2.2.2/32

Last SID index: 200

Flags : -

# Display backup IS-IS SR prefix-SID mappings.

<Sysname> display isis segment-routing prefix-sid-map backup-policy

ISIS 1 - Backup policy

Page is loading ...

Aruba R9F19A Reference guide

This manual is also suitable for

Aruba R9F19A Reference guide

Related papers

Other documents