Page is loading ...
1
1
2
MIXING AMPLIFIER PB 210P
3
PB 310P
4
PB 610P
5
PB1010P
6
7
8
9
10
11
12
13
14
15
16
O W N E R ’ S M AN U AL
17
18
Before operating, please read this manual carefully.
19
20
21
FEATURES
22
2MIC inputs，3AUX inputs, and 1AUX output.
23
4-16Ω rated output.
24
6-zone output.
25
Individual volume control and output level indication for each zone output.
26
Mute function for priority input.
27
Treble and Bass control
28
Chime with priority output
29
5-unit LED Meter for monitoring volume output in each zone.
30
Output short circuit protection and caution.
31
2
FRONT PANEL
1
2
3
4
5
6
7
8
9
10
11
12
13
1 Power Switch 7 MIC 1 Priority Input Jack
14
2 LED Power Indicator 8 Zone Volume Adjustment Button (1-6)
15
3 Bass Adjustment Button 9 5-unit LED Level Meter
16
4 Treble Adjustment Button 10 Chime Button
17
5 AUX Input Volume Adjustment Button 11 Zone Level Indicator
18
6 MIC Input Volume Adjustment Button
19
20
Note:
21
When all five units of the LED level meter remain lit, it indicates that the sound is distorted. In
22
such case, adjusting each volume adjustment button until LED unit 4 (+8dB) and LED unit 5
23
(+10dB) flash.
24
25
REAR PANEL
26
27
28
29
30
31
32
33
34
1 Mute control Button 5 6-zone Output
35
2 MIC 2 Input Jack 6 AC Power Source Insert
36
3 AUX Input Jack 1, 2, 3 7 Fan Exhaust Window
37
4 AUX Output Jack 8 Speaker Output Terminal
38
(Link with another amplifier or recording equipment) 9 Fuse
39
3
CONNECTIONS (without multi-zone outputs)
1
2
3
4
5
6
7
8
9
CONNECTIONS
(with multi-zone outputs)
10
11
12
13
14
15
16
17
18
19
20
21
Note:
22
Individual zone opening and closing may be achieved by adjusting Zone Volume Adjustment
23
Button on Front Panel.
24
To MIC 1 Input
Jack on Front Panel
MIC 1 with Priority
Input
Tuner, CD,
Cassette
Recorder or
another Amp.
MIC 1
MIC 1 with Priority
Input
To MIC 1 Input
Jack on Front Panel
MIC 2 Tuner, CD,
Cassette
Recorder or
another Amp.
4
MUTE FUNCTION
1
MIC 1 Input Jack and Chime Button have the highest level of priority. Input signals from
2
them can override other input signals. The grade of this MUTE function can be adjusted.
3
4
5
6
7
8
9
PRECAUTION OF INSTALLATION
10
11
1. Do not block ventilation holes.
12
2. The amplifier should not be placed in any of the areas:
13
1) with poor ventilation;
14
2) exposed to direct sunlight;
15
3) with high ambient temperature or adjacent to heat-generating equipment;
16
4) with high humidity or heavy dust;
17
5) susceptible to vibration.
18
3. Make sure the power outlet conforms to the plug of the unit.
19
4. Do not use this unit if the electrical power cord is frayed or broken.
20
5. Always operate the unit with the ground wire
21
6. If a short alarm rings after turning on power and inputting signals, there must be an
22
output short circuit fault. In such case, power should be cut off immediately. Do not
23
turn on the power until the fault is removed.
24
25
26
27
28
29
30
31
MUTE
MIN MAX
5
SPECIFICATIONS
1
2
Model PB-210P PB-310P PB-610P PB-1010P
Rated Output 60W 120W 250W 350W
Output Regulation Less than 3dB, from off-load to full load
MIC: 3.0mV(±0.5dB)
Input sensitivity
LINE: 300mV(±50dB)
Frequency Response 80Hz-16kHz (±3dB)
Distortion Less than 0.5% (at 1kHz)
MIC: more than 71dB
Ratio of
Signal to Noise LINE: more than 85dB
Bass: ±10dB（at 100Hz）
Tone
Treble: ±10dB（at 10kHz）
Protection DC voltage; overload; short-circuit.
Mute Input signals from MIC 1 override other input signals
Power
Requirements AC 220-240V/50-60Hz
Power
Consumption 120W 250W 500W 650W
Outer Packing Size(mm)
(L×W×H)520×430×195
Unit Size (mm) (L×W×H)418×338×88
Gross Weight 11.7kg 13.5kg 16kg 17kg
Net Weight 9.7kg 11.5kg 14kg 15kg
Specifications are subject to change without notice
3
4
5
6
7
8
LY International Electronics Co., Ltd.
9
CAUTION
● When the “Power switcher” is off, please pull out the power cord from the socket.
Please keep the equipment out of water.
● To reduce the risk of electric shock, do not remove the cover.
● Please contact us or authorized dealers for servicing.
/
