Vector Technology VT700CR Operating instructions

OPERATION MANUAL

OF FUNCTION SETTING

GSM IC-Card

PAYPHONE

MODEL: VT700CR

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 1 -

Installation:

Getting Started：

：：

：Before initial installing the SIM Card to the payphone, please disable your SIM card PIN

code on your cell phone in advance.

If the SIM card requests a PIN CODE to activate, but you do not disable the PIN code in advance, when

the GSM payphone starts initially, LCD will display NO PIN CODE. Please enter Function Setting

Mode COMMAND 01: Function 01 to enter your PIN code.

1 ) Insert SIM card ：Open the front door to find the SIM card holder near the door hinge to insert your SIM

card. Clip down the SIM card securely.

2) Please plug in the AC power Adaptor. When the Solar Power supply connection is not established ready

yet, the main power supply is provided from AC power only.

3) Wait for about 30 seconds for network registration process and the LCD displays -- GSM POWER ON--

SIM TEST OK – Signal Quality xx –

4) The Payphone LCD screen displays

“

“W

WE

EL

LC

CO

OM

M”

” in idle mode (on-hook status). Lift up the handset to

display “Welcome” “Insert Card” to make calls.

A) Function Setting Item List of COMMAND (00-31):

The payphone provides 31 Function setting items (COMMAND) via keypad programming feature. Before setting the

parameters to your phone, please make sure what you want to do, prepare the operational manual by your side and

follow the instructions carefully. If you don’t understand what the function is, don’t change anything, but leave the default

value for safety.

Function Setting Item List of COMMAND (00-31):

Page

Function 00 : Self-Diagnosis 4

Function 01 : SIM card pin code setting 5

Function 02 : Define Local/STD/IDD Area Prefix number (Tariff table prefix number setting) 6

Function 03 : RMS, SIM Card number programming 9

Function 04 : Incoming call time setting 9

Function 05 : RMS, SIM Card number programming 9

Function 06 : Warning Tone 10

Function 07 : SIM card designate setting 10

Function 08 : Total collected money display 10

Function 09 : (Reserved) 11

Function 10 : Meter signal selection 11

Function 11 : Owner password setting 12

Function 12 : (Reserved) 12

Function 13 : Language mode Selecting. 13

Function 14 : The credit of indication of rate Program 15

Function 15 : Time group & Indication of Rate's time program 16

Function 17 : The gateway number setting 17

Function 18 : Speed dial programs (10 sets) 17

Function 19 : Real Time Clock Setting 17

Function 20 : Discount time setting 18

Function 24 : Simple discount program 19

Function 27 : Software checking number. 19

Function 30 : Parameter setting 20

How to set a rate completely 20

Q&A 22

FCT Specification 23

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 2 -

B) How to enter the Function Setting Mode of COMMAND ( 00-31):

1) Please open the front door and pick up the handset. Slightly ouch the Function door switch (see the photo below).

Function/Door switch

2) LCD will display “COMMAND (00-31)”. If not, please hang up the handset to wait for 5 seconds, and try again.

3) Enter the COMMAND number of the Function Items you want to program and follow the instructions page 4 -22 to

set the parameters.

4) After finishing the programming, LCD will return to command screen：

LCD Display

COMMAND(00-31)

5) Press REDAIL key to save the data entered, LCD will show SAVING while the data is saving.

LCD Display Operation

1.COMMAND(00-31) Press “REDAIL” to save

2. SAVING Wait for around 10 seconds

Important note:

When the LCD shows “ SAVING”, it means the data is saving into the memory chip. Please don’t close the front door or

put the handset back to cradle. Make sure the function switch is open and handset is off hook to avoid any in-completed

data saving process to lead the micro-chip losing memory and causing permanent damage to the phone.

Don’t close the front door. Make sure the function switch is open.

6) If there is no change of the setting, no update data will be saved. The LCD will show ENDING

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 3 -

7) If you touch the function switch carelessly or a power failure happens during the data saving, after the phone regaining

the power, it will be starting to activate. The LCD screen will turn from *****GSM****** to xxxxxGSMxxxxxx for 0.5

second. It means the data is not being saved correctly during the previous step. Please re-enter the COMMAND mode

again and complete the data-saving process correctly to save the data by following the correct steps.

C ) FOLLOW ON and REDAIL key definition for programming purpose:

“FOLLOW ON”

“REDIAL”

a. Press the "FOLLOW ON" key to exit without saving from programming &to return to Command mode.

b. Press the "REDIAL" key to save the programming data and return to Command mode.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 4 -

Function 00 : Self-Diagnosis

When LCD displays COMMAND (00 –31), please enter 00 to start Function 00:

"Self-Diagnosis"

Diagnostic items: KEYBOARD unit

Function and door SWITCH

HOOK SWTICH unit

HANDSET unit

LCD DISPLAY unit

Operation LCD Display

SELECT (0-1)

Select "0" to run step 1 KEYPAD TEST

(0) 0000000000000000

(1) 1111111111111111

(2) 2222222222222222

(3) 3333333333333333

(4) 4444444444444444

(5) 5555555555555555

(6) 6666666666666666

(7) 7777777777777777

(8) 8888888888888888

(9) 9999999999999999

(*) ****************

(#) ################

(FOLLOW ON) NNNNNNNNNNNNNNN

(REDIAL) RRRRRRRRRRRRRRRR

(LOUD) LLLLLLLLLLLLLLLLL

Door and function switch open CASHBOX OUT

Door and function switch close CASHBOX IN

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 5 -

Function 01: SIM card PIN code program

Note: this function is only necessary when you do not disable the PIN code on your cell phone in advance.

When LCD displays COMMAND (00 –31), please enter 01 to start Function 01:

SIM card PIN

code program

Operation LCD Display

COMMAND(00-30)

Press "01" OWNER PASS:

Key the PIN code OWNER PASS: ****

Press" REDIAL" to save

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 6 -

Function 02: Define Local/STD/IDD Area Prefix number

(Tariff table prefix number setting)

Note: This function 02 helps you define the Local/STD/IDD CALL AREA Telephone Prefix

Numbers. We define 3 Call Areas below:

0 : Local CALL AREA : The Prefix number is 1, 2,3,4,5,6,7,8 or 9. (1 digit)

1: STD CALL AREA : The Prefix number is 0. ( 1 digit)

2: IDD CALL AREA : The Prefix number is 00. ( 2 digits)

Example:

If you would like to program the prefix number 00886XXXX…. is 1 dollar for 60 seconds.

You need to program 00886 in the IDD Call Area. Because 00886 prefix with 00, the default of

IDD Call Area prefix number is 00.

Then, we need to program the rate. The rate is 1 dollar for 60 second will be program in Function

14 and Function 15.

In Function 02, we only program the indication of Rate. There are 47 sets indication of Rate.

Now, we choose the Rate 07 which is 1 dollar for 60 seconds. (Please check the Function 14 and

Function 15 later)

LCD Display Operation

1) COMMAND (00-31) press 02

2) FUN PASS: **** 8080( enter 8080 password)

3) CALL AREA (0/2): press 2 (0 for LOCAL,1 for STD,2 for IDD Call

Area)

4) IDD 000-399: press 000(The Serial No.000-399 total is 400sets

for IDD Call Area )

5) 000: enter 00886 and press REDAIL key (00886 is

the Prefix Code ; press REDAIL to save )

6) 000:00886 07 enter 07 and REDAIL key ( 07 is the indication

of Rate , press REDAIL to save)

7) CALL AREA (0/2):

Notes: 1) Function Password: It can be changed in function 23.

2) Indication of Rate :

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 7 -

There are 47 sets indication of Rate. After we call the indication 7 is Rate”07”.

When we program the 00886 prefix number will follow the Rate”07”. All the phone

number will follow the tariff with Rate”07”.

How do you define the Rate”07” to follow 1 dollar for 60 seconds? Please check the

function 14 and function 15 later.

3) The default for indication of rate :

Rate"00" is default rate of LOCAL Call Area.

( The prefix number 1, 2, 3, 4, 5, 6, 7, 8 or 9 which doesn’t program in the LOCAL Call

Area will follow the Rate”00”)

Rate"01" is default rate of STD Call Area.

( The prefix number 0 which doesn’t program in the STD Call Area will follow the

Rate”01”)

Rate"02" is default rate of IDD Call Area.

( The prefix number 00 which doesn’t program in the LOCAL Call Area will follow the

Rate”02”)

Rate"46" is default rate of FREE CALL.

Rate"47" is default rate of BARRED CALL.

4) Serial No. of Call Area :

Local Call Area: 000-199 , total 200 sets.

STD Call Area : 000-399, total 400 sets.

IDD Call Area : 000-399, total 400 sets.

5) Priority :

For the CALL AREA : The priority is IDD , STD, then LOCAL CALL AREA.

For the Serial no of Call Area :

High Serial no. will be prior than low serial no.

Example:

We program the 00886 prefix number in the IDD CALL AREA and in the Serial No.

000.

LCD Display Operation

8) COMMAND (00-31) 02

9) FUN PASS: **** 8080( Input password)

10) CALL AREA (0/2): 2 (0 for LOCAL,1 for STD,2 for IDD Call Area)

11) IDD 000-399: 000(The Serial No.000-

399 total is 400sets for

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 8 -

IDD Call Area )

12) 000: press 00886 and REDAIL key (00886 is the

Prefix Code ; REDAIL to save )

13) 000:00886 07 07 and REDAIL key( 07 is the indication of

Rate , REDAIL to save )

Next, we continue to program the 008867 prefix number in the IDD CALL AREA and

the Serial No. 001

14) CALL AREA (0/2): 2 (0 for LOCAL,1 for STD,2 for IDD Call Area)

15) IDD 000-399: 001(The Serial No. 000-

399 total is 400sets for

IDD Call Area )

16) 001: 008867 and REDAIL key (008867 is the Prefix

Code ; REDAIL key to save)

17) 001:008867 08 08 and REDAIL ( 08 is the indication of Rate ,

REDAIL to save)

18) CALL AREA (0/2):

After finishing the program, when we dial 008867XXX, the tariff will follow Rate”08”.

If you program the 00886 in Serial No. 001 and the 008867 in Serial No. 000.

When we dial 008867XXXX, the tariff will follow the Rate”07”.

Since the CHIP system program check is starting from Serial No. 399 to 000, the priority

001 prevails over 000.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 9 -

Function 03: RMS, SMS caller ID

The Function is to save the RMS of SMS Caller ID to the payphone.

Please see the RMS manual for the operation.

Function 04: Incoming call

To program the time limited of the incoming call

Example: If you want to set the time of incoming call for 10 minutes.

Operation LCD Display

COMMAND(00-30)

Press "04" INCOMING: 0M

Press "1" to increase to 10 INCOMING: 10M

Note:

Press "1" one time will decrease 1 minute, "3" will increase 1 minute.

The Min is 0 M. The Max is 100 M.

Function 05: RMS, the SIM card number programming

To use the RMS function, please make sure that RMS function is available for your

payphone. CPU and Flash Memory chip should be upgraded.

Step 1 Exchange RMS cell phone's SIM card with payphone's SIM card

Step 2 Set RMS cell phone's numbers under function 05, then it'll return to

command mode

Step 3 Enter function 03, you'll see the screen showing" SAVE" and payphone will

send SMS to itself. When you hear "Di Di", it means SMS is successful. Payphone

will return to command mode again

Step 4 Be sure to press "REDIAL" key to save the data.

Step 5 Exchange SIM CARDS BACK.

Please read the

G

GG

GSM

SM SM

SM RMS

RMS RMS

RMS Operation Manual

Operation Manual Operation Manual

Operation Manual

for details.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 10 -

Function 06: Warning Tone Setting

To program when the Warning Tone appears before disconnection.

Example: If you want to set the warning tone appear in 10 seconds before disconnection.

Operation LCD Display

COMMAND(00-30)

Press "06" WT: 0S

Press "4" to increase to 10 WT: 10S

Note:

1) Press "1" one time will decrease 0.1 sec., "3" will increase 0.1 sec.

2) Press "4" one time will decrease 1 sec., "6" will increase 1 sec.

Function 07: The SIM card lock setting

You can program a specific SIM card in this function. The payphone will be working with the SIM

card only you program.

Example: To enable this function. Please insert the SIM card you prefer to lock before plugging

the power.

Operation LCD Display

COMMAND(00-30)

Press "07" SIM.PRESET :0/1 0

Press "1" to Enable ENABLE

Press "Redial" to save

If you want to disable it, please Press "0'.

Function 08: Total Collected Money Display

Display only.

SUM is total collected money from this payphone installed. PURSE is the balance from crediting

air time values.

Note: if you want to clear the balance here, please refer to function 30.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 11 -

Function 09: (Reserved)

Function 10: Metering Signal Selecting

There are two metering Signal Selections (0) Auto detection, (1) Auto + C. Normally, please set

(0) Autodetection as default. (1) Auto+ C is special function to cooperate with gateway terminal

and owner should also set gateway numbers under Function17

Set the phone to tariff on the GSM system via auto detection.

Operation LCD Display

COMMAND(00-30)

Press "10" METER(0-1)

Press "0" select auto detection AUTODETECTION

Note: If you select "1" for Gateway system, please program the function 17 also.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 12 -

Function 11: Owner password setting

To set the password for the free call. 1 to 10 digits.

Operation LCD Display

COMMAND(00-30)

Press "11" OWNER PASS :

Please key in the password "1234567" 1234567

You can set for max 10 digital.

and press "redial" to save

How to use: Pick up the handset. Press the "louder" key, the LCD will ask the pass word.

Key in the owner password and press the "Redial" It can make a free call.

Function 12: (Reversed)

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 13 -

Function 13: Language Mode Selecting

There are two language modes you can choose. 0 is for English, 1 and 2 are for other languages.

Example: if you want to select the second mode.

Operation LCD Display

COMMAND(00-30)

Press "13" ENG / OTHER (0/2):

Press "1" to select local language

Press "Redial" to save

Note:

You can press the" follow on" button to change the language display before dialing the telephone

number.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 14 -

Function 14: The credit of indication of rate Program

This function is to program the credit of the indication of rate.

If you choose the tariff by payphone ( In function 10 you choose tariff by payphone itself),

you need to program the credit of the indication of rate.

There are 47 sets indication of rate for programming. But the Rate”46” and Rate “47” is fix.

Rate”46” 



 Free call

Rate “47”



 Barred call

Example:

In the function 02, we program the prefix number 00886 will follow the Rate”07”. Now, we

program the credit of the Rate “07” in function 14. The credit is 1 dollar for 60 seconds. We

program 1 dollar in function 14.

LCD Display Operation

1. COMMAND(00-31) 14

2. TAXE(1) press 1 and REDAIL key( This is for system tariff ,

please read below)

3. TAXE(2) press 1 and REDAIL key ( This is for system tariff ,

please read below)

4. RATE(00-47): 07 and REDAIL key (Program the Rate”07”

5. MIN.1

ST 1 ( 1 dolla

r for the minimum credit the user should

insert to make a call)

6. MIN 2 ND: 2 ( When the MIN.1 ST credit run out, User should

insert 2 dollar to keep this call continue.)

7. RATE(00-47): You can continue to program other indication of rate.

Note. 1) In function 10, you choose :

. (4) REVERSE＋_SELF (5) 50Hz_＋_SELF

(6) 16KHz_＋_SELF (7) 12KHz_＋_SELF

(8) AUTODECT

It will tariff by payphone.

2) The TAXE(1) , TAXE(2) , is for the system Tariff. Please program the minimum credit in

TAXE(1) , TAXE(2), when you choose the tariff by payphone itself.

If you choose the tariff by system ( In function 10 you choose tariff by system), you need to

program the credit of TAXE(1) and TAXE(2).

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 15 -

Example : The tariff is by System. Each metering signal will take 1 dollar credit.

LCD Display Operation

1. COMMAND(00-31) 14

2. TAXE(1) 1 and REDAIL key(The first metering signal from

system, the payphone will take 1 dollar credit. )

3. TAXE(2) 1 and REDAIL key ( The second and after metering

signal from system, the payphone will take 1 dollar credit)

4. RATE(00-47): 07 and REDAL key ( If you would like to the prefix

number 00886 will be asked for 1 dollar minimum insert, you can program the indication of

rate or you may ignore it.)

5. MIN.1

ST

1 ( 1 dollar for the minimum credit the user should

insert to make a call)

6. MIN 2 ND: 2 ( When the credit is less than Taxe(2), User should

insert 2 dollar to keep this call continue. Or the

payphone will disconnect this call when it receive

the next metering signal )

Note. 1) In function 10, you choose :

. (0) REVERSE (1) METERING_50Hz

(2) METERING_16KHz (3) METERING_12KHz

It will tariff by system.

2) In the example, if you program the prefix number 00886 in Function 02, and the MIN.1

ST and MIN 2 ND in function 14. When user dial the 00886XXX numbers, the payphone

will ask for the minimum credit 1 dollar to make a call and 2 dollar for keeping this call

continue.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 16 -

Function 15: Time group & Indication of Rate's time program

This function is to program the time of the indication of rate.

If you choose the tariff by payphone itself (In function 10 you choose tariff by payphone

itself), you need to program the Time of the indication of rate.

There are 47 sets indication of rate for programming. But the Rate”46” and Rate “47” is

fixed.

Rate”46” 



 Free call

Rate “47”



 Barred call

Thus, there are Rate 00-45 can be programmed.

TIME GROUP (FOR Discount time program, please check the function 20 later):

The Time Group has 18 sets, Group (00-17), for discount programming. Normal rate (no

discount) is group 00. In this function, You can set the communication time (seconds) for each

rate at different discount time. (Discount time is defined in function 20).

Example:

Follow function 02 and 14 example, we want to program the prefix number 00886 is 1 dollar for

60 seconds.

LCD Display Operation

1. COMMAND(00-31) 15

2. GROUP(00-17) 00 (Set for normal time first , please read the notes

below )

3. RATE(00-45) 07

4. RATE: 60 S 60 S

5. RATE(00-45) You may program other indication of Rate.

Notes:

1) There are 18 sets time groups. There is Rate”00-47” in each time groups. Thus, in

different time will follow the different tariff rate. How to program the time zone? Please

check the Function 20. Please check the Function 20.

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 17 -

.

Function 17: Gateway number setting

You can program the gateway numbers in this function.

Function 18: Speed dial programs

User can press “MEMO function key” +“0(1/2/3/4/5/6/7/8/9)” for a speed dial call. Due to

less choice in hot line function, this function can compensate owner to set many hot line phone

numbers.

Example:

If you want to set speed dial number “MEMO 0”=”22678080”. The rest can be done in the same

manner. “MEMO 1”=“12345678”, “MEMO 2”=“87654321”, etc.

Operation LCD Display

COMMAND(00-30)

Press “18” SPEEDDIAL(0-9)

Press “0” SPEEDDIAL(0-9)

“22678080” “Redial”

Function 19: Real Time clock Setting

Example: Set the 2003/3/28 09:50:45 Wednesday

Operation LCD Display

COMMAND(00-30)

Press "19" REAL TIME CLOCK INPUT

KEY IN YEAR YEAR :2003

KEY IN MONTH MONTH:03

KEY IN DAY DAY: 28

KEY IN HOUR HOUR: 09

KEY IN MIN MINUT: 50

KEY IN SEC SECOND: 45

KEY IN WEEK WEEKDAY:3

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 18 -

Function 20: Discount time Setting

You can define what time interval is for discount rate which set under function 15.

Example:

Follow function 15’s example. We should define the time interval for discount rate. The time we

set is period 00, everyday, AM00:00~06:00, group 01

Operation LCD Display

COMMAND(00-30)

Press "20" PERIOD(00-17)

Press "00" to select the first period CLOCK INPUT

The total periods are 18 sets (00-17)

Key "0230060000060001" 0230060000060001

Press "Redial" to save

Note:

1) Phone must have real time clock(RTC) hardware support.

2) Format:

02 30 0 6 00 00 06 00 01

month day week week hour min. hour min group

start end start start end end

3) Month: 2 digits, ranging form 01 to 12, if key in 00 means any month

Day: 2 digits, ranging from 01 to 31 & 00 means any day

Weekday: 1 digit, ranging from 0 (Sunday) to 6 (Saturday)

Hour: 2 digits, ranging from 00 to 23.

Minute: 2 digits, ranging from 00 to 59

Time group: 2 digits, ranging from 0 to 23

4) If hour setting across to another day must be divided into two time periods ex. 9:00pm to

6:00am You should set first period 9:00pm to 11:59pm, second period 00:00am to 6:00am.

Group 00 is normal rate, no discount.

Time group corresponds to Function 15

Vector Technology Co. – GSM IC-CARD Payphone Manual

GSM IC-Card PAYPHONE - 19 -

Function 24: Simple discount program

Our function 24 is to set all rates increase/decrease percentage no matter normal or discount time

Example: Adjust the rate to 200% (double)

Operation LCD Display

COMMAND(00-30)

Press "24" DISCOUNT: 100%

Press "3" to increase to 200% DISCOUNT: 200%

Press "Redial" to save

The Call Time Discount Discounted time

180S 50% 90S

180S 120% 216S

180S 200% 360S

Note1): Press “1” to decrease, “3” to increase

2): The discount range: from 0%~200%

Function 27: Software Version NB.

Show the software check sum.

Operation LCD Display

COMMAND(00-30)

Press "27" AA08

"AA08" is the software's check sum.

Page is loading ...

Vector Technology VT700CR Operating instructions

Vector Technology VT700CR Operating instructions

Other documents