Ninja BL771 User manual

Brand: Ninja

Model: BL771

Category: Blenders

Type: User manual

www.ninjakitchen.com

1 877 646-5288

BL771

OWNER’S GUIDE

Mega Kitchen System

1-877-646-5288

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING ELECTRICAL APPLIANCES,

BASIC SAFETY PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED, INCLUDING THE

FOLLOWING:

READ ALL INSTRUCTIONS BEFORE

USING YOUR NINJA

MEGA KITCHEN

SYSTEM

POLARIZED PLUG

WARNING: To reduce the risk of

electric shock, this appliance has a polarized

plug (one blade is wider than the other). This

plug will ﬁt into a polarized outlet only one

way. If the plug does not ﬁt fully into the

outlet, reverse the plug. If it still does not ﬁt,

contact a qualiﬁed electrician to install the

proper outlet. DO NOT modify the plug in

any way.

WARNING: Extension cords are

not recommended for use with this product.

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK OR INJURY:

1 WARNING: Remove utensils prior to

processing. Failure to remove may

cause the jar to be damaged or to

shatter which may cause personal

injury.

2 WARNING: Stacked Blade Assembly

is sharp, not locked in place and

removable, handle with care. When

handling the Stacked Blade Assembly,

always hold it by the shaft. Failure to do

so will result in a risk of laceration.

3 WARNING: Stacked Blade Assembly

is sharp and not locked in place. If

using the pour spout, ensure the lid is

fully locked onto the pitcher. If pouring

with the lid removed, carefully remove

the Stacked Blade Assembly ﬁrst,

holding it by the shaft. Failure to do so

will result in a risk of laceration.

4 WARNING: Chopping Blade

Assembly and Mini Prep Bowl Blade

Assembly are sharp and not locked in

place. Before emptying contents

carefully remove lid and Chopping

Blade Assembly or Mini Prep Bowl

Blade Assembly, holding it by the shaft.

Failure to do so will result in a risk of

laceration.

5 CAUTION: Do not blend hot liquids,

doing so may cause excessive pressure

build-up, resulting in risk of the user

being burned.

6 CAUTION: We do not recommend

grinding in any of our Nutri Ninja

™

cups.

7 CAUTION: Remove the Nutri Ninja

Blade Assembly from the cup upon

completion of blending. Some

ingredients have the potential to

expand after blending resulting in

excessive pressure buildup that can

pose a risk of injury.

8 To protect against electrical shock, do not

submerge the appliance or allow the power

cord to come into contact with water or any

other liquid.

9 DO NOT allow the appliance to be used by

children. Close attention is necessary when

used near children. This is not a toy.

www.ninjakitchen.com

10 Never leave an appliance unattended when

inuse.

11 Appliance accessories are not intended to

be used in the microwave as it may result in

damage to the accessories.

12 Turn the appliance Off and remove the

power cord from the electrical outlet

when not in use, before assembling or

disassembling parts and before cleaning.

To unplug, grasp the plug and pull from the

electrical outlet. Never pull from the power

cord.

13 DO NOT abuse the power cord. Never carry

the appliance by the power cord or yank it

to disconnect from electrical outlet; instead

grasp the plug and pull to disconnect.

14 DO NOT operate any appliance with a

damaged cord or plug, or after the appliance

malfunctions, has been dropped or damaged

in any manner. This appliance has no

serviceable parts. Return the appliance to

SharkNinja Operating LLC for examination,

repair or adjustment.

15 DO NOT let the power cord hang over

the edge of table or counter or touch hot

surfaces such as the stove.

16 Always use appliance on a dry, level surface.

17 Keep hands, hair, clothing, as well as

utensils out of container while processing to

reduce the risk of severe injury to persons

or damage to the appliance. A scraper may

be used but only when the appliance is not

running.

18 Avoid contact with moving parts.

19 DO NOT attempt to sharpen blades.

20 DO NOT use the appliance if blade

assemblies are bent or damaged.

21 To reduce risk of injury, never place the

blade assemblies on the base without

the pitcher or Nutri Ninja

cup properly

attached.

22 DO NOT operate this appliance on or near

any hot surfaces (such as gas or electric

burner or in a heated oven).

23 The use of attachments or accessories

including canning jars, not recommended by

the manufacturer may result in ﬁre, electric

shock or personal injury.

24 DO NOT remove the container from the

motor base while the appliance is in

operation.

25 To reduce the risk of injury, NEVER operate

the appliance without the lid in place; DO

NOT try to defeat the interlock mechanism;

make sure that the attachment is properly

installed before operating the appliance.

26 DO NOT expose containers to extreme

temperature changes.

27 DO NOT overﬁll.

28 DO NOT operate the appliance empty.

29 If the appliance overheats, a thermal switch

will become activated and shut off the

motor. To reset, unplug the appliance and let

it cool down for approximately 15 minutes

before using again.

30 THIS PRODUCT IS INTENDED FOR

HOUSEHOLD USE ONLY. Do not use

this appliance for anything other than its

intended use. Do not use outdoors.

31 The maximum rating is based on the

Stacked Blade Assembly (pitcher) that drives

the greatest power and other recommended

attachments may draw signiﬁcantly less

power or current.

SAVE THESE

INSTRUCTIONS

1-877-646-5288

THIS BOOK COVERS MODEL NUMBER:

BL771

TECHNICAL SPECIFICATIONS

Voltage: 120V., 60Hz.

Power: 1500 Watts

Pitcher Capacity: 72 oz. (9 cups, 2.15 L)

MAX Liquid Capacity: 64 oz. (8 cups, 1.9 L)

Bowl Capacity: 64 oz. (8 cups, 1.8 L)

Mini Prep Bowl Capacity: 24 oz. (3 cups, 710 ml)

Nutri Ninja

Cup Capacity: 16 oz. (2 cups, 470 ml)

www.ninjakitchen.com

Contents

Thank you for

purchasing

the Ninja

Mega Kitchen

System

Getting to Know Your Ninja

Mega Kitchen System

....................................................5

Before First Use ........................................................................................................7

Assembly and Use for the Blender Pitcher ..................................................................8

Assembly and Use for the Nutri Ninja

Cup ...............................................................10

Assembly and Use for the Food Processor Bowl ........................................................11

Assembly and Use for the Mini Prep Bowl .................................................................13

Speed Setting & Uses ..............................................................................................14

Care & Maintenance ...............................................................................................15

Troubleshooting Guide .............................................................................................16

Replacement Parts ..................................................................................................16

Warranty & Registration ...........................................................................................22

1-877-646-5288

Getting To Know Your Ninja

Mega Kitchen System

NOTE: Blade Assemblies are not interchangeable.

b c

f g

d 64 oz. Food Processor Bowl

e Bowl Lid with Locking Handle

f Chopping Blade Assembly (bowl)

g Dough Blade Assembly (bowl)

h 24 oz. Mini Prep Bowl

i Spindle for Mini Prep Bowl

j Mini Prep Bowl Blade Assembly

a 16 oz. Nutri Ninja

Cup (x2)

b To-Go Lid (x2)

c Nutri Ninja Blade Assembly

k 72 oz. Blender Pitcher

l Pitcher Lid with Locking Handle

m Stacked Blade Assembly (pitcher)

n Motor Base

o Power Cord (not shown)

www.ninjakitchen.com

FEATURES:

• Patented Ninja

Technology

• Extra Large, 72 oz. Blender Pitcher (maximum liquid capacity 64 oz.) - BPA Free

• 64 oz. Food Processor Bowl with Drizzle Hole - BPA Free

• 24 oz. Mini Prep Bowl - BPA Free

• Nutri Ninja

Cups - BPA Free

• Lock-In Lid, Featuring Pour Spout

• Easy to Clean Electronic Control Panel

• Sturdy, Non-Slip Base

1-877-646-5288

Before First Use

PLEASE KEEP THESE IMPORTANT

SAFEGUARDS IN MIND WHEN USING THE

APPLIANCE:

IMPORTANT: Make sure that the motor base

is plugged in for use.

IMPORTANT: Never add ingredients into the

container before placing the Blade Assembly

in ﬁrst.

IMPORTANT: Blade Assemblies are not

interchangeable.

IMPORTANT: DO NOT attempt to operate the

appliance without the lid on.

IMPORTANT: Never run the appliance empty.

IMPORTANT: Appliance accessories are not

intended to be used in the microwave as it

may result in damage to the accessories.

CAUTION: Do not immerse the motor base into

water or any other liquid.

1 Remove all packaging material and labels from the

appliance. Separate/remove all parts from each other.

2 Wash the lids, pitcher, bowls, Nutri Ninja

cups and

blade assemblies in warm, soapy water. When washing

the blade assemblies, use a dish-washing utensil with a

handle to avoid direct hand contact with blades.

WARNING: Handle the Blade Assemblies with

care when washing, as the blades are sharp.

3 Handle blade assemblies with care to avoid contact

with sharp edges. Rinse and air dry thoroughly.

4 The pitcher, bowls, Nutri Ninja cups, lids and

Blade Assemblies are all dishwasher safe. It is

recommended that the lids and Blade Assemblies

be placed on the top rack. Ensure that the Blade

Assemblies are removed from the containers before

placing in the dishwasher.

5 Wipe the motor base clean with a damp cloth.

WARNING: Stacked Blade

Assembly is sharp and not

locked in place. If using the

pour spout, ensure the lid is

fully locked onto the blender

pitcher. Failure to do so will

result in a risk of laceration.

WARNING: Stacked

Blade Assembly is sharp

and not locked in place.

If pouring with the lid

removed, carefully remove

the Stacked Blade Assembly

ﬁrst, holding it by the shaft.

Failure to do so will result in

a risk of laceration.

WARNING: Chopping

Blade Assembly is sharp and

not locked in place. Before

emptying contents carefully

remove lid and Chopping

Blade Assembly, holding it by

the shaft. Failure to do so will result in a

risk of laceration.

www.ninjakitchen.com

Assembly and Use for the Blender Pitcher

WARNING: Handle the Stacked Blade Assembly with care, as the blades are sharp.

WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or

to shatter, which may cause personal injury.

WARNING: Never leave the appliance unattended while in use.

CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the

user being burned.

IMPORTANT: Make sure that the motor base is plugged in for use.

Fig. 3bFig. 1 Fig. 4 Fig. 5

ASSEMBLY

Fig. 3a

Fig. 2

1 Review warning and caution statements above before

proceeding to number 2.

2 Place the motor base on a clean, dry, level surface

such as a counter or table top.

3 Align and lower the Pitcher onto the motor base.

(Fig. 1) Handle should be aligned slightly to the right of

the “LOCK” symbol on the motor base.

4 Rotate the blender pitcher clockwise until it clicks in

place. As the pitcher rotates, it will lower and the safety

tabs on the bottom of the pitcher will slide under the

safety tabs on the top of the motor base. (Fig. 2)

5 The pitcher can be placed on the motor base two ways;

the handle can be on the front right corner or the front

left corner. (Fig. 3a, Fig. 3b)

6 Holding the Stacked Blade Assembly by the top of the

shaft, place it onto the drive gear inside the pitcher.

Ensure that the Stacked Blade Assembly is seated

properly and is standing upright. (Fig. 4)

NOTE: The Stacked Blade Assembly will ﬁt loosely on

the drive gear.

7 Add the ingredients to the pitcher, making sure that

they do not exceed the highest measured marking line

on the side of the pitcher.

NOTE: If you need to add additional ingredients while

the appliance is processing, open the pour spout cap

and pour the ingredients in through the opening.

NOTE: When blending any kind of liquids, such as

mixtures of any drinks or smoothies, do not exceed the

“Max liquid” mark (64 ounces) on the pitcher.

8 Plug the power cord into the electrical outlet and press

the power button ( ).

IMPORTANT: As a safety feature, the power

button ( ) will ﬂash and the motor will not work

if the pitcher and lid are not installed correctly.

When the pitcher and lid are installed properly,

the power button ( ) will be solid, indicating that

the appliance is ready for use.

9 Holding the lid by the handle in the upright position,

place it on top of the pitcher aligning the arrow ( )

located on the lid with the arrow ( ) located on the

pitcher’s handle. (Fig. 5) Press the handle down until

you hear a click.

1-877-646-5288

Assembly and Use for the Blender Pitcher - cont.

Fig. 7

USE

REMOVAL

Fig. 6 Fig. 8 Fig. 9

10 Review ALL warning and caution statements before

proceeding.

11 Select the speed that best suits your needs. (Fig. 6)

NOTE: Pulse ingredients for even chopping by pressing

down in short intervals.

11 When you have reached your desired consistency, stop

the appliance by pressing the power button ( ) and

wait for the blade assembly to stop turning. (Fig. 7)

13 To remove the lid, press the release button on the lid,

pull the lid handle up to a 90° angle and lift the lid off.

Turn the pitcher counter clockwise and then lift off the

base. (Fig. 7, Fig. 8)

WARNING: Never insert your hands in the pitcher

as the Stacked Blade Assembly is sharp. Always

use a spatula to dislodge food that has stuck to

the sides of the pitcher.

14 Open the pour spout cap and use the spout to empty

liquid contents.

15 For thicker consistencies, ﬁrst remove the lid by

pressing the release button and pulling the lid handle

up to a 90 degree angle to lift lid off the pitcher. Then,

carefully remove the Stacked Blade Assembly by the

top of the shaft. Place Stacked Blade Assembly away

from the work area to avoid accidental contact. Finally,

empty contents from the pitcher.

16 Make sure that the unit is unplugged when not in use.

17 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor base

and gently pull the unit up and towards you. (Fig. 9)

www.ninjakitchen.com

Assembly and Use for the Nutri Ninja

Cup

1 Review warning and caution statements above before

proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Add ingredients to the Nutri Ninja

cup.

4 Place the Nutri Ninja Blade Assembly onto the cup and

screw it tightly until you have a good seal. (Fig. 1)

5 Turn the Nutri Ninja

cup upside down and place it

onto the motor base, aligning the tabs on the cup with

the motor base. Turn the Nutri Ninja

cup clockwise to

lock into place. You will hear a click when the lock is

engaged. (Fig. 2) Turn the power button on, the single

serve button will illuminate.

6 Press down on the Single Serve button in short

intervals to activate. (Fig. 3)

7 Once you have reached your desired consistency,

turn the power button off. Turn the Nutri Ninja

cup

counter-clockwise and pull straight up to remove.

(Fig. 4, Fig. 5)

Fig. 3 Fig. 4 Fig. 5

ASSEMBLY USE REMOVAL

NOTE: Do not overﬁll! To avoid spilling, do not add

ingredients past the “Max” ﬁll line.

8 Turn the cup upright and remove the Nutri Ninja Blade

Assembly by twisting the blade assembly counter-

clockwise.

9 Place the To-Go drinking lid onto the Nutri Ninja

cup,

twist to seal and enjoy!

10 Make sure that the motor base is unplugged when not

in use.

11 To release the motor base from

the counter or table top, place your

hands underneath both sides of the

motor base and gently pull the unit

up and towards you. (Fig. 6)

NOTE: To order additional Nutri

Ninja

Cups, please visit our website:

www.ninjakitchen.com or feel free to contact

customer service: 1-877-646-5288.

Fig. 2Fig. 1

For best results, use short “PULSES”... Practice makes perfect!!

Fig. 6

WARNING: Handle the Nutri Ninja Blade Assembly with care, as the blades are sharp.

WARNING: Remove utensils prior to processing. Failure to remove may cause the Nutri Ninja cup to be

damaged or to shatter, which may cause personal injury.

WARNING: Never leave the appliance unattended while in use.

CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the

user being burned.

CAUTION: Remove the Nutri Ninja Blade Assembly from the cup upon completion of blending. Some

ingredients have the potential to expand after blending resulting in excessive pressure buildup that can pose

a risk of injury.

IMPORTANT: Make sure that the motor base is plugged in for use.

1-877-646-5288

Assembly and Use for the Food Processor Bowl

ASSEMBLY

1 Review warning and caution statements above before

proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Align and lower the Bowl onto the motor base. (Fig. 1)

Handle should be aligned slightly to the right of the

“LOCK” symbol on the motor base.

4 Rotate the bowl clockwise to lock into place. You will

hear a click when the lock is engaged. (Fig. 2)

5 The bowl can be placed on the motor base two ways;

the handle can be on the front right corner or the front

left corner. (Fig. 3a, Fig. 3b)

6 Holding the desired Blade Assembly by the top of the

shaft, place it onto the drive gear inside the bowl.

Ensure that the Blade Assembly is seated properly and

is standing upright. (Fig. 4)

NOTE: The Blade Assembly will ﬁt loosely on the drive

gear.

7 Add the ingredients to the bowl, making sure that they

do not exceed the highest measured marking line on

the side of the bowl.

8 Holding the lid by the handle in the upright position,

place it on top of the bowl aligning the arrow ( )

located on the lid with the arrow ( ) located on the

bowl’s handle. (Fig. 5) Press the handle down until you

hear a click.

NOTE: The 64 oz. bowl is not intended for

blending drinks. Do not overﬁll.

NOTE: To add liquids during processing,

open the drizzle hole on the top of the

lid and pour the liquid slowly into the

mixture.

9 Plug the power cord into the electrical

outlet and press the power button ( ).

IMPORTANT: As a safety feature, the power

button ( ) will ﬂash and the motor will not work

if the bowl and lid are not installed correctly.

When the bowl and lid are installed properly, the

power button ( ) will be solid, indicating that the

appliance is ready for use.

Fig. 4 Fig. 5Fig. 1

Fig. 3a

Fig. 3bFig. 2

WARNING: Chopping Blade Assembly is sharp and not locked in place. Before emptying contents carefully

remove lid and Chopping Blade Assembly, holding it by the shaft. Failure to do so will result in a risk of

laceration.

WARNING: Remove utensils prior to processing. Failure to remove may cause the bowl to be damaged or to

shatter, which may cause personal injury.

WARNING: Never leave the appliance unattended while in use.

CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the

user being burned.

CAUTION: Remove the lid from the bowl upon completion of processing. Some ingredients have the potential

to expand after blending resulting in excessive pressure buildup that can pose a risk of injury.

IMPORTANT: Make sure that the motor base is plugged in for use.

www.ninjakitchen.com

USING THE CHOPPING BLADE ASSEMBLY

1 Review warning and caution statements at the top of

page 11 before proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Secure the bowl onto the motor base.

4 Holding the Chopping Blade Assembly by the shaft,

place it onto the gear shaft inside the bowl. Ensure that

the Chopping Blade Assembly ﬁts around the gear shaft

and that it is standing straight. (Fig. 1)

5 Add the ingredients and secure the bowl lid onto the

bowl. (Fig. 1)

6 Plug the power cord into the electrical outlet and press

on the power button ( ). (Fig. 2) Select the speed

that best suits your needs. Pulse ingredients for even

chopping by pressing down in short intervals.

NOTE: Please refer to “Speed Settings & Uses” chart

for suggested uses and speeds.

7 When you have reached your desired consistency, stop

the appliance by pressing the power button ( ) and

wait for the Chopping Blade Assembly to stop turning.

8 To remove the lid, press the release button on the lid

and pull the lid handle up to a 90° angle. (Fig. 2)

9 Turn the bowl counter-clockwise and lift it to remove it

from the motor base. (Fig. 3)

10 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor

base and gently pull the unit up and towards you.

(Fig. 4)

USING THE DOUGH BLADE ASSEMBLY

IMPORTANT: Use only the “DOUGH” button when

using this attachment.

1 Review warning and caution statements at the top of

page 11 before proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Secure the bowl onto the motor base.

4 Holding the Dough Blade Assembly by the shaft, place

it onto the gear shaft inside the bowl. Ensure that the

Dough Blade Assembly ﬁts around the gear shaft and

that it is standing straight. (Fig. 5)

5 Add the ingredients and secure the bowl lid onto the

bowl. (Fig. 5)

NOTE: For best results add wet ingredients ﬁrst and

then add dry ingredients.

6 Plug the power cord into the electrical outlet and press

on the power button ( ). (Fig. 2)

7 To remove the lid, press the release button on the lid

and pull the lid handle up to a 90° angle. (Fig. 2)

8 Turn the bowl counter-clockwise and lift it to remove it

from the motor base. (Fig. 3)

9 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor

base and gently pull the unit up and towards you. (Fig. 4)

REMOVAL

Fig. 5

USE

CHOPPING BLADE

ASSEMBLY

Fig. 1 Fig. 2 Fig. 3 Fig. 4

USE

DOUGH BLADE

ASSEMBLY

1-877-646-5288

ASSEMBLY

Assembly and Use for the 24 oz. Mini Prep Bowl

USE REMOVAL

Fig. 5

Fig. 1

Fig. 3 Fig. 4

Fig. 2

1 Review warning and caution statements above before

proceeding to number 2.

2 Place the 64 oz. bowl onto the motor base. (See

assembly instructions on page 11.)

3 Holding the spindle by the shaft, place it onto the gear

shaft inside the 64 oz. bowl. Ensure that the Mini Prep

Bowl Blade Assembly ﬁts around the gear shaft and

that it is standing straight. (Fig. 1)

4 Place the mini prep bowl aligning the spindle inside the

center post. (Fig. 2)

5 Hold the Mini Prep Bowl Blade Assembly by the shaft

and carefully place it over the center post of the mini prep

bowl. (Fig. 3)

6 Add ingredients into the mini prep bowl.

NOTE: Do not ﬁll ingredients past the “MAX” ﬁll line.

7 Holding the lid by the handle in the upright position, place

it on top of the 64 oz. bowl aligning the arrow ( ) located

on the lid with the arrow ( ) located on the bowl’s handle.

(Fig. 4) Press the handle down until you hear a click.

8 Plug the power cord into the electrical outlet and press

on the power button ( ).

9 Select the speed that best suits your needs. For best

results, press the Pulse button in short intervals. (Fig. 5)

NOTE: Please refer to “Speed Settings & Uses” chart

for suggested uses and speeds.

10 When you have reached your desired consistency, stop

the appliance by pressing the power button ( ) and

wait for the Mini Prep Bowl Blade Assembly to stop

turning.

11 To remove the lid, press the release button on the lid

and pull the lid handle up to a 90° angle. (Fig. 6)

12 Carefully hold the Mini Prep Bowl Blade Assembly by

the shaft and lift it out of the mini prep bowl. (Fig. 7)

13 Turn the bowl counter-clockwise and lift it to remove it

from the motor base.

14 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor

base and gently pull the unit up and towards you. (Fig. 8)

Fig. 6 Fig. 7

Fig. 8

WARNING: Handle the Mini Prep Bowl blade assembly with care as the blades are sharp, and not locked in

place. Before emptying the contents of the Mini Prep Bowl, carefully remove the Blade Assembly ﬁrst,

holding it by the shaft. Failure to do so will result in a risk of laceration.

WARNING: Remove utensils prior to processing. Failure to remove may cause the Mini Prep Bowl to be

damaged or to shatter, which may cause personal injury.

WARNING: Never leave the appliance unattended while in use.

CAUTION: Remove the lid from the Mini Prep Bowl upon completion of processing.

IMPORTANT: Make sure that the motor base is plugged in for use.

www.ninjakitchen.com

FUNCTION CONTAINER ATTACHMENT

SPEED

BUTTON

TYPE OF FOOD

Single Serve

Blending

Nutri Ninja

Cup Nutri Ninja Blade Assembly Single Serve

Smoothies

Frappes

Milk Shakes

Mincing

Nutri Ninja Cup

Mini Prep Bowl

Nutri Ninja Blade Assembly

Mini Prep Bowl Blade

Assembly

Single Serve

Pulse

Onion

Garlic

Herbs

Kneading Bowl Dough Blade Assembly 1

Bread dough

Pie dough

Pizza dough

Pretzel dough

Dough Mixing Bowl Dough Blade Assembly 1 Cookie dough

Processing

Pitcher

Bowl

Nutri Ninja Cup

Mini Prep Bowl

Stacked Blade Assembly

Chopping Blade Assembly

Nutri Ninja Blade Assembly

Mini Prep Bowl Blade

Assembly

Pulse

Single Serve

Pâtés

Stewed fruits

Dips

Apple sauce

Spreads

Soups*

Baby food

Emulsifying

Bowl

Mini Prep Bowl

Chopping Blade Assembly

Mini Prep Bowl Blade

Assembly

Salad Dressings

Dips

Sauces*

Grinding Bowl Chopping Blade Assembly 2 Meat

Grating

Bowl

Nutri Ninja Cup

Chopping Blade Assembly

Nutri Ninja Blade Assembly

3 or Pulse

Single Serve

Grated cheese

Bread crumbs

Spices

Chopping

Bowl

Nutri Ninja Cup

Mini Prep Bowl

Pitcher

Chopping Blade Assembly

Nutri Ninja Blade Assembly

Mini Prep Bowl Blade

Assembly

Pulse

Single Serve

Salsa

Vegetables

Nuts

Mixing Bowl Dough Blade Assembly 1

Light cake mixes

Batters

Ice Crushing

Pitcher

Nutri Ninja Cup

Stacked Blade Assembly

Nutri Ninja Blade Assembly

Single Serve

Ice

Pureeing

Pitcher

Nutri Ninja Cup

Stacked Blade Assembly

Nutri Ninja Blade Assembly

Single Serve

Smoothies

Smooth soups

Milkshakes

Speed Setting & Uses

* When blending sauces and soups, make sure they’re cooled to room temperature ﬁrst - Ninja

containers are not intended

for hot blending.

1-877-646-5288

HOW TO CLEAN

CAUTION: Make sure that the motor base is

unplugged from the power source before inserting

or removing any blade assembly and before

cleaning.

CAUTION: DO NOT immerse the motor base into

water or any other liquid.

CAUTION: Handle the blade assemblies with care,

as the blades are very sharp.

1 Separate/remove all parts from each other.

2 Hand Washing: Wash the lids, pitcher, bowls, Nutri

Ninja

cup and blade assemblies in warm, soapy

water. When washing the blade assemblies, use a

dish-washing utensil with a handle to avoid direct hand

contact with blades. Handle blade assemblies with care

to avoid contact with sharp edges. Rinse and air dry

thoroughly.

Dishwasher: The containers, lids, blade assemblies

and attachments are all dishwasher safe. The lids

and blade assemblies are top rack dishwasher safe.

Ensure that the blade assemblies are removed from the

containers before placing in the dishwasher.

WARNING: Handle the Blade Assemblies with

care when washing, as the blades are sharp.

Contact with the blades’ edges can result in

laceration.

3 Wipe the motor base clean with a damp cloth

. .

Please call customer service if any servicing needs to

be performed on the appliance at 1-877-646-5288.

HOW TO STORE

Store the Ninja

Mega Kitchen System

upright the blade

assembly inside the corresponding container with the lid

secured on top. Do not place anything on top. Store the

rest of the attachments in a safe place where they will

not be damaged and won’t cause harm. Loosely wrap the

power cord around the motor base

RESETTING THE MOTOR THERMOSTAT

The Ninja Mega Kitchen System features a unique safety

system which prevents damage to the unit’s motor and drive

system should you inadvertently overload your appliance.

If the appliance is being overloaded, the motor will

stop. Allow the appliance to cool for approximately

15 minutes. To reset the appliance, follow the resetting

procedure below:

1 Unplug the appliance from the electrical outlet.

2 Remove and empty the container and ensure that no

food is jamming the Blade Assembly.

3 Allow the appliance to cool for approximately 15

minutes.

4 Re-install the container onto the base and re-plug the

appliance into the electrical outlet.

5 Proceed to use the appliance as before making sure not

to exceed the recommended maximum capacities.

Care & Maintenance

www.ninjakitchen.com

Troubleshooting Guide

Replacement Parts

ORDERING REPLACEMENT PARTS

To order additional parts and attachments, please visit our website: www.ninjakitchen.com

or feel free to contact customer service: 1-877-646-5288.

PROBLEMS POSSIBLE REASONS & SOLUTIONS

Motor Doesn’t Start or Blade

Assembly Doesn’t Rotate.

Make sure the container is securely locked on the motor base.

Make sure the lid is securely on the container in the correct position (align arrows).

The appliance is turned “Off”. Press the power button ( ) to turn “On”.

Check that the plug is securely inserted into the electrical outlet.

Check the fuse or circuit breaker.

The unit has overheated or overloaded. Unplug and wait approximately 15

minutes before usingagain.

Check to make sure the unit is not overloaded.

Food is Unevenly Chopped.

Either you are chopping too much food at one time, or the pieces are not of even

size and processing smaller amounts per batch.

Food is Chopped Too Fine or is

Too Watery.

The food has been over processed. Use pulse button for controlled processing.

Food Collects On Lid or On the

Sides of the Container.

The mixture is too thick. Add more liquid.

You Cannot Achieve Snow

From Solid Ice.

Do not use ice that has been sitting out or has started to melt. Use ice straight

from the freezer.

Start with a few pulses and then go to a continuous blending cycle.

Motor Base Won’t Stick to

Counter or Table Top.

Make sure surface and suction feet are wiped clean. Suction feet will only stick to

smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood,

tile and non-polished ﬁnishes.

DO NOT attempt to use appliance when the motor base is stuck to a surface that

is not secure, (cutting board, platter, plates, etc.).

1-877-646-5288

Notes

www.ninjakitchen.com

PRODUCT REGISTRATION

Please visit www.ninjakitchen.com or call 1-877-646-5288 to register your new Ninja

product within ten (10) days of

purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.

The registration will enable us to contact you in the unlikely event of a product safety notiﬁcation. By registering you

acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.

ONE (1) YEAR LIMITED WARRANTY

SharkNinja Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1)

year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and

exceptions.

The liability of SharkNinja Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.

This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or

used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or

damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused by

or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been

performed by a repair person not authorized by SharkNinja Operating LLC.

If your appliance fails to operate properly while in use under normal household conditions within the Limited Warranty period,

you may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For Customer Service

support, call 1-877-646-5288 or visit our website www.ninjakitchen.com.

If the appliance is found by SharkNinja Operating LLC to be defective, in SharkNinja Operating LLC’s sole discretion, we

will repair or replace it free of charge. Proof of purchase date and a check made payable to SharkNinja Operating LLC in the

amount of $19.95 to cover the cost of return shipping and handling must be included.*

This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional

warranties. The responsibility of SharkNinja Operating LLC if any, is limited to the speciﬁc obligations expressly assumed

by it under the terms of this Limited Warranty. In no event is SharkNinja Operating LLC liable for incidental or consequential

damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or

consequential damages, so the above may not apply to you.

This Limited Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state or from

province to province.

*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and

to attach tag to item before packing with your name, complete address and phone number with a note giving

purchase information, model number and what you believe is the problem with the item. We recommend you insure

the package (as damage in shipping is not covered by your Limited Warranty). Mark the outside of your package

“ATTENTION CUSTOMER SERVICE”.

SharkNinja Operating LLC

US: Newton, MA 02459

CAN: Ville St-Laurent, QC H4S 1A7

1-877-646-5288

www.ninjakitchen.com

Mega Kitchen System, Ninja and Nutri Ninja, are registered trademarks of

SharkNinja Operating LLC.

Illustrations may differ from actual product. We are constantly striving to improve our

products, therefore the speciﬁcations contained herein are subject to change without notice.

For SharkNinja U.S. Patent information visit www.sharkninja.com/USPatents.

BL771_30_E_16014_3

PRINTED IN CHINA

Ninja BL771 User manual

Brand: Ninja

Model: BL771

Category: Blenders

Type: User manual

Download PDF

report

Ninja BL771 User manual

Ninja BL771 User manual

Related papers

Other documents