KRAUS KGW-1700SN-CL Installation guide

INSTALLATION MANUAL

Single Lever Vessel Glass Waterfall

Bathroom Faucet

KGW-1700

Thank you for your purchase

We would like to take this opportunity to thank you for choosing Kraus.

We hope that you are completely satised with your purchase, and enjoy it for years

to come. If you have any questions, or require technical assistance, please contact

us at 800.775.0703 and one of our representatives will be happy to help.

For more information about Kraus products, please visit:

www.kraususa.com

In order to activate your warranty and get faster access to customer support, please

register your new Kraus product at:

www.kraususa.com/registration

Sincerely,

Kraus USA Customer Service

For technical assistance or replacement parts, please contact Kraus

Customer Service and one of our representatives will be happy to help:

Toll-Free: 800-775-0703 or Customerservice@kraususa.com

Prior to Installation:

•

Make sure you have all necessary parts by checking the diagram and parts list. If

any part is missing or damaged, please contact Kraus Customer Service at 800-

775-0703 for a replacement

• Turn o the hot and cold water supply at the angle stops and turn on the old

faucet to release any built up pressure. Remove existing faucet. Clean sink or

countertop to remove any debris, plumber’s putty, or silicone

• Place bucket under angle stops. Turn on angle stops to ush any debris prior to

installing new plumbing. Shut o angle stops

• Pre-drilled hole size requirement: 1 3/8” (min)

• Max countertop thickness: 1 3/8”

Diagram and Parts List

1

2

3

4

5

8

9

6A

6B

6C

6D

7

Diagram and Parts List

Tools you will need:

1

10

279

10 31/32”

Minimum distance 90mm

Less than 90mm

Cold Water

32 3/32”

Ø35~Ø38

1

2

3

10

9

11

12

13

Hexagon Nut

Hot

Water

Cold

Water

2 3

1

4

5

7

6

8

4

5

6

7

8

Ø1 3/8”~

Ø1 1/2”

815

194

7 5/8”

Ø1 3/8~Ø1 1/2”

30˚

10

11

Close

Open

Left

Hot Water

Push

25˚

90˚

12

13

8

7

Ø35~Ø38

Max35

217

8 17/32”

Max1 3/8”

9

11

12

13

2

3

4

5

6

7

8

Adjustable Wrench

Phillips Screwdriver

Pipe Tape

1. Decorative Ring

2. Glass Disc

3. Lever

4. Seal for Glass Disc

5. Faucet Body

6. Mounting Hardware

(A) Rubber Washer

(B) Metal Washer

(C) Mounting Nut

(D) Mounting Screws

7. Hot & Cold Waterlines (2)

8. Hex Wrench

9. Manual

Dimensions

7 1/8"

(181mm)

1 1/4"-18UNEF-2A

2 5/16"

(59mm)

1/16"~1 3/4"

(1mm~44mm)

2 1/8"

(54mm)

Ø 2 5/8"

(Ø67mm)

5/16"~3/8"

(7.2mm~8.8mm

58.2°

6 1/8"

(155mm)

12.5°

11 1/4"

(286mm)

10 7/16"

(265mm)

12 11/16"

(322mm)

3 9/16"

(90mm)

7 11/16"

(195mm)

9/16"-24UNEF-2B

22 1/16"

(560mm)

12.5°

Dimensions

7 1/8"

(181mm)

1 1/4"-18UNEF-2A

2 5/16"

(59mm)

1/16"~1 3/4"

(1mm~44mm)

2 1/8"

(54mm)

Ø 2 5/8"

(Ø67mm)

5/16"~3/8"

(7.2mm~8.8mm

58.2°

6 1/8"

(155mm)

12.5°

11 1/4"

(286mm)

10 7/16"

(265mm)

12 11/16"

(322mm)

3 9/16"

(90mm)

7 11/16"

(195mm)

9/16"-24UNEF-2B

22 1/16"

(560mm)

12.5°

Step 1: Remove Mounting Hardware

Remove mounting hardware

(6A, B, C, & D) from the

mounting pipe

Step 2: Remove Decorative Ring

Remove decorative ring (1)

from faucet body (5)

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

Install glass disc (2) on faucet

body (5). Secure it using

decorative ring (1)

Step 4: Install Faucet

Insert faucet body (1) into

the hole on the countertop.

Attach rubber washer (6A),

metal washer (6B), mounting

nut (6C), and mounting screws

(6D) from underneath the sink

Step 3: Install Glass Disc

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

NOTE: Hand-tighten only

(decorative ring)

Step 5: Secure Mounting Hardware

Step 6: Connect Waterlines to Main Valve

Adjust direction of faucet body

(5). Tighten mounting nut (6C)

until snug. Tighten mounting

screws (6D) to nut with a

Phillips head screwdriver until

snug

Connect hot and cold waterlines

(7) to the angle stops. Tighten

with a wrench until snug. Turn

on hot and cold angle stops and

check for leaks

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

NOTE: Make sure O-rings

are installed on both

ends of the hot & cold

waterlines

Step 7: Flush Faucet

Turn water on for a minute to

ensure proper water ow

6A

6B

6C

6D

6A

6B

6C

6D

5

1

2

5

blue Line

Cold

red Line

Hot

Open

Hot

Cold

Replacement Parts

1A

1B

2

3

4

5

6

7

8

9A

9B

9C

9D

10

1. (A) Decorative Ring

(B) O-ring

2. Glass Disc

3. Lever

4. Seal for Glass Disc

5. Locking Nut

6. Cartridge

7. Flow Restrictor

8. Hot & Cold Waterlines

9. Mounting Hardware

(A) Rubber Washer

(B) Metal Washer

(C) Mounting Nut

(D) Mounting Screws

10. Hex Wrench

Trouble - Shooting

If you have followed the instructions carefully and your faucet still does not work

properly, take the following corrective steps:

PROBLEM CAUSE ACTION

Leakage under the

handle

Locking nut has come

loose

Unscrew the decorative

ring (by hand) and

remove the glass disc.

Loosen set screw with

a hex wrench located

underneath lever and

remove lever. Tighten

locking nut with a

reversible wrench

Water will not shut off

completely

Cartridge may be

defective

Unscrew decorative

ring (by hand) and

remove glass disc.

Loosen set screw with

a hex wrench located

underneath lever and

remove lever. Unscrew

locking nut with a

reversible wrench.

Remove ceramic disc

cartridge. Check for

cracks

Drain is leaking Washers may be

compromised or

installed incorrectly

Check washers to make

sure they are installed

correctly and not

cracked

Codes/Standards Applicable:

NSF/ANSI 372

NSF/ANSI 61

ASME A112.18.1M

2.2GPM 8.3L/min maximum

LEAD FREE

I

A

P

M

O

R

&

T

TM

HELP LINE

Our customer service hours are Monday – Friday, 9am – 8pm EST.

Be sure to visit our website at www.kraususa.com

If you are a homeowner please contact a Kraus Customer Service Representative at:

Kraus USA, Inc.

12 Harbor Park Drive

Port Washington, NY 11050

Toll-free 800-775-0703

[email protected]

If you are a plumbing contractor or trade professional please contact a Kraus Pro

Representative at:

Kraus USA, Inc.

12 Harbor Park Drive

Port Washington, NY 11050

516-801-8955

[email protected]

If you are an Authorized Partner please contact a Partner Support Representative at:

Kraus USA, Inc.

12 Harbor Park Drive

Port Washington, NY 11050

516-801-8954

Partnersupport@kraususa.com

In requesting warranty service, please be ready to provide:

1. Proof of purchase.

2. A description of the problem.

Care & Maintenance

*To keep the product clean & shining, follow the steps below:

1. Rinse with clean water & dry with a soft cloth

2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners

3. Do not use cloth with a coarse surface

4. Unscrew the aerator and clean when necessary

*This installation manual is subject to change without further notice.

1

10

279

10 31/32”

Minimum distance 90mm

Less than 90mm

Cold Water

32 3/32”

Ø35~Ø38

1

2

3

10

9

11

12

13

Hexagon Nut

Hot

Water

Cold

Water

2 3

1

4

5

7

6

8

4

5

6

7

8

Ø1 3/8”~

Ø1 1/2”

815

194

7 5/8”

Ø1 3/8~Ø1 1/2”

30˚

10

11

Close

Open

Left

Hot Water

Push

25˚

90˚

12

13

8

7

Ø35~Ø38

Max35

217

8 17/32”

Max1 3/8”

9

11

12

13

2

3

4

5

6

7

8

Download the Kraus Care & Maintenance Guide at:

http://www.kraususa.com/maintenance

Receive Proof of Ownership

Access Customer Care & Installation Help

Get Exclusive Kraus Oers & Promotions

Scan to Register Online

or visit http://www.kraususa.com/registration

Please take a moment to share your experience.

Visit http://www.kraususa.com/review to let us know what you think

about your new Kraus product.

Contact Us to Learn More

1.800.775.0703 / www.kraususa.com / [email protected]

Like & Follow KrausUSA

Download the Kraus Care & Maintenance Guide at:

http://www.kraususa.com/maintenance

www.kraususa.com

REGISTER YOUR PRODUCT TODAY

We’re always looking for ways to improve.

KRAUS KGW-1700SN-CL Installation guide

KRAUS KGW-1700SN-CL Installation guide

Related papers

Other documents