Badger Basket 561 Assembly Instructions

Badger Basket
Brand
Badger Basket
Model
561
Category
Strollers
Type
Assembly Instructions

This manual is also suitable for

4.0/0309/HF
PRODUCT MODEL
NUMBERS:
00561 - Pink Rosebud
00562 - Pink Gingham
00563 - Pink/White Polka Dot
09922 - Navy/White
Page 1 of 4
JUST LIKE MOMMY
3-IN-1 DOLL
PRAM/CARRIER/STROLLER
Assembly Instructions.
Adult Assembly Required.
Read all instructions before use.
Save instructions for future use.
VERSION CODE:
4.0/0309/HF
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday to Thursday 7:30 AM-4:30 PM CST)
Web: http://www.badgerbasket.com/parts • E-mail: p[email protected]
Mail: PO Box 227, Edgar, WI 54426-0227 • Phone: 715-352-2311 • Fax: 715-352-3163
4.0/0309/HFPage 2 of 4
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware. If anything is missing or not satisfactory, please
DO NOT call the store or return the product to them. Contact Badger Basket.
Most problems are resolved without you needing to leave home.
When contacting us, please have this instruction manual, your product model
number, and your product version code ready.
For fastest service, go to http://www.badgerbasket.com/parts
Your Product Version Code is:
4.0/0309/HF
READ ALL INSTRUCTIONS before use of this product.
Keep instructions for future use. Use only the parts and hardware provided by
Badger Basket. Do not use the product if it is damaged or broken.
Product and/or hardware may include small parts or screws with sharp points.
Choking Hazard! Keep unassembled parts out of the reach of small children.
DO NOT allow anyone to climb or play on or inside of this product. Periodically
check to make sure all the screws remain tight. This item is designed for
children who are THREE (3) YEARS OF AGE AND OLDER. IT IS A TOY ONLY
AND NOT FOR USE WITH REAL INFANTS OR PETS.
WARNING - FAILURE TO FOLLOW THESE
WARNINGS AND THE INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH
PARTS INCLUDED:
(A) 1 - Stroller/Frame
(B) 2 - Metal Axle Rods
(C) 4 - Wheel Spacers
(not shown)
(D) 4 - Wheels
(E) 1 - Carrier/Pram Unit
with pad, boot, and hood
A
B
D
E
USE AND
CARE INSTRUCTIONS:
Wipe metal and plastic parts
clean with a damp cloth and
mild soap as needed.
Spot clean fabric with mild
detergent and cold
water as needed.
4.0/0309/HFPage 3 of 4
PICTURE 2A
PICTURE 1A
A
B
STEP 1: See PICTURES 1A and 1B. Insert the TWO METAL
AXLE RODS (B) through the holes in the STROLLER FRAME
(A). Slide ONE WHEEL SPACER (C) onto each of the FOUR
ends of the METAL AXLE RODS (B).
STEP 2: See PICTURES 2A and 2B. Attach the FOUR
WHEELS (D) to the ends of the AXLE RODS (B). To attach
the wheels, squeeze the metal bracket to open it, slip the wheel
onto the end of the rod, and release the bracket. The brackets
lock over the ends of the rods and if you tug on the wheels they
should not come off.
STEP 3: See PICTURE 3. Unfold the stroller, and slide the frame
locks down until they cover the ends of the tubes to secure the
stroller in the open position. To fold the stroller, simply slide the
locks up until the tubes are free to fold back down.
To adjust the position of the stroller seat, press down on the seat
frame, as shown in PICTURE 4 on PAGE 3, until it is the posi-
tion you want. You will hear the adjustment dials click as the seat
position is adjusted. The STROLLER is now assembled!
PICTURE 2B
PICTURE 1B
C
B
PICTURE 3
B
4.0/0309/HFPage 4 of 4
STEP 4: See PICTURES 5, 6A, and 6B. Set the stroller frame aside and locate the CARRIER/PRAM UNIT (E). Take off the
fabric boot and remove the fabric pad. Unfold the metal frame support bars inside and snap them under the plastic clips that are
attached to the bottom board of the carrier (PART E).
Next replace the fabric pad and the boot as shown in PICTURE 6A. Prop open the hood by snapping the support bars together
on both sides of the hood, as shown in PICTURE 6B. To fold the carrier, reverse this step. The CARRIER is now ready for
play!
STEP 5: See PICTURES 7A and 7B. To use as a pram, position the stroller seat so that it is flat/horizontal. Set the carrier on top
of the stroller seat (facing forward or backward - either is OK) as shown in PICTURE 7A. Snap the clips on the STROLLER
FRAME over the metal side bars on the CARRIER as shown in PICTURE 7B. Be sure the clips are snapped properly to hold
the carrier tight to the frame. The PRAM is now ready for play!
PICTURE 7B
PICTURE 7A
PICTURE 4
PICTURE 6A
E
PICTURE 5
PICTURE 6B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Badger Basket 561 Assembly Instructions

Badger Basket
Brand
Badger Basket
Model
561
Category
Strollers
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents