E-flite EFLAEC503 Operating instructions

E-flite
Brand
E-flite
Model
EFLAEC503
Category
Soldering irons
Type
Operating instructions

This manual is also suitable for

E-flite EFLAEC503 is a high-quality EC5 connector set designed for use with batteries, electronic speed controls, and charge leads. The set includes both male and female connectors, which are easily assembled using a soldering iron and solder.

The EC5 connectors are made from durable materials and are designed to withstand high currents and voltages. They are also easy to use, with a simple push-to-connect design that makes it easy to connect and disconnect wires. A big advantage of EC connectors is their compact design and low weight. Moreover, their gold-plated contacts provide excellent conductivity and corrosion resistance.

E-flite EFLAEC503 is a high-quality EC5 connector set designed for use with batteries, electronic speed controls, and charge leads. The set includes both male and female connectors, which are easily assembled using a soldering iron and solder.

The EC5 connectors are made from durable materials and are designed to withstand high currents and voltages. They are also easy to use, with a simple push-to-connect design that makes it easy to connect and disconnect wires. A big advantage of EC connectors is their compact design and low weight. Moreover, their gold-plated contacts provide excellent conductivity and corrosion resistance.

EC Connector Assembly
Thank you for purchasing E-flite’s EC2, EC3 and EC5 connectors. The steps outlined below will help you install the appropriate
EC connector on your batteries, electronic speed controls, charge leads and more.
A few tools are required for EC connector assembly.
• 40-watt soldering iron
• Rosin-core solder (like WSD2020)
• Pliers
• Wire stripper
• 1.5mm hex driver or small flat blade screwdriver
• EC3 DEVice (male) or BATTery (female) connector set
The Assembly Process
Step One:
Strip one wire lead to expose about 2-3mm of wire. IMPORTANT NOTE: When installing Battery connectors, be
especially sure to strip, solder and install one wire/connector at a time to prevent the chance of an accidental short.
Step Two:
Using the soldering iron and solder, tin the exposed end of the wire. Be sure to completely tin the wire to avoid a possible cold
or poor solder joint.
Step Three:
Lightly tin the inside of the EC gold “bullet” connector (try not to use too much solder in order to prevent excess solder from
flowing to the outside of the bullet connector in the next step). IMPORTANT NOTE: The female “tubes” are used for the
BATTery connectors, and the male “pins” are used for charger, ESC or other DEVice connectors.
Step Four:
Place the tinned wire into the tinned bullet connector while heating the joint with the soldering iron. A cleaned and tinned
soldering iron tip will help provide a clean and secure solder joint. Be sure to keep excess solder from flowing onto the outside
of the bullet connector. Excess solder on the outside of the bullet connector will make it difficult/impossible to install the bullet
connector in the plastic connector housing. Use a sharp hobby knife (and extreme care) or a rotary tool with a grinding stone or
cutting wheel to remove any excess solder from the outside of the bullet connector.
Step Five:
While the bullet connector is still warm from the soldering process, insert it into the back of the appropriate plastic
connector housing. Make sure to verify the polarity before inserting the bullet connector, as marked on the outside of the plastic
connector housing. Push the bullet connector into the plastic housing with a 1.5mm hex driver or small flat blade screw driver
and moderate to strong pressure, with the front of the plastic connector housing firmly seated on a solid surface. You will feel a
“pop” when the bullet connector is properly locked into the plastic housing.
Step Six:
Repeat steps 1-5 with the other wire lead. At this point assembly of your EC connector is complete.
We hope the detailed steps answer any questions you might have. However, we have posted a detailed assembly video online
at www.horizonhobby.com if you would like to see the process first-hand. We hope you enjoy the ease of use and performance
of your new EC2, EC3, or EC5 connectors. If you have any questions, please contact Horizon’s product support team at
877-504-0233 or by email at:
productsupport@hoizonhobby.com.
In Germany, call +49 4121 46199 60 or by email at: info@horizonhobby.de
In England, call +44 (0) 1279 641097 or by email at:
sales@horizonhobby.co.uk
© 2008 Horizon Hobby, Inc
www.horizonhobby.com
E-fliteRC.com
  • Page 1 1

E-flite EFLAEC503 Operating instructions

E-flite
Brand
E-flite
Model
EFLAEC503
Category
Soldering irons
Type
Operating instructions
This manual is also suitable for

E-flite EFLAEC503 is a high-quality EC5 connector set designed for use with batteries, electronic speed controls, and charge leads. The set includes both male and female connectors, which are easily assembled using a soldering iron and solder.

The EC5 connectors are made from durable materials and are designed to withstand high currents and voltages. They are also easy to use, with a simple push-to-connect design that makes it easy to connect and disconnect wires. A big advantage of EC connectors is their compact design and low weight. Moreover, their gold-plated contacts provide excellent conductivity and corrosion resistance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents