PAC AAICHY User manual

Brand: PAC

Model: AAICHY

Type: User manual

This manual is also suitable for

AAI-CHY

PAC AAICHY allows you to connect external audio devices to your 2005+ Chrysler vehicle's factory radio. It features two RCA inputs for auxiliary audio sources, which can be selected using the radio's SEEK buttons. The device also includes a 3-pin connector for connecting to the vehicle's VES or satellite input, and a red wire with a fuse holder for providing +12V accessory output. With the AAICHY, you can enjoy your favorite music or audio content from external devices through your vehicle's sound system.

Paciﬁ c Accessory Corporation - Santa Ana, CA 92705

[email protected] • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com

Pacific Accessory Corporation

12-03-08

J1850

Class 2

VPW

Class 2

J1850

1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0

1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0

Arbitration

EOD

CRC

1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0

1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0

Class 2

J1850

AAI-CHY

Auxiliary Audio Input for 2005+ Chrysler Vehicles

If vehicle has Factory Satellite and Video Entertainment System (VES), either one must be disconnected in order for the AAI-

CHY to work properly. If vehicle has factory single disc radio and satellite, the satellite receiver must be disconnected.

10 pin

22 pin

Auxiliary Audio Inputs

Accessory Output

+12volts 1amp max.

Purple, Black, Green (VES input)

Output

Pacific Accessory Corporation • Santa Ana, CA

Chrysler Auxiliary Audio Input

Acce sso ry

Left

Righ t

Aux1

Aux2

Red = Ac ces sory ou tpu t

Left

Righ t

2005-2006

Vehicles with

CAN Bus

White, Brown, Gray (Satellite input)

Installation:

The AAI-CHY plugs into the back of the factory

radio.

1. Remove factory radio. Remove factory female

10 pin Satellite cable, if available. Plug the

AAI-CHY’s 10 pin SAT plug into the radio.

Plug the factory Satellite cable that was

just removed into the AAI-CHY’s 10 pin

connector.

2. Insert the AAI-CHY’s 22 pin main power Plug

(T-Harness) in between the factory radio and

factory harness.

3. Connect external audio device(s) into Aux 1

and/or Aux 2 inputs using the RCA jacks on

the AAI-CHY.

4. If the vehicle has both factory Satellite and

VES, you must disconnect either one directly at the device. If the vehicle has factory single disc radio, the Satellite receiver

must be disconnected directly at the device . Refer to vehicle’s repair manual for location and removal of the Satellite receiver

or VES plug.

5. By default the AAI-CHY output plug (3 pin connector) should be connected to the VES input harness of the 10 pin T-harness. If

the vehicle has factory VES or the factory radio is a single disc (REF), use the Satellite input of the 10 pin t-harness.

Note: The AAI-CHY will emulate the VES by default. If the vehicle has factory VES or the radio is a single disc, the AAI-

CHY will emulate the Satellite receiver automatically.

RED wire with fuse holder: Accessory Output. You can use this wire to turn on DVD/VCP players. This wire provides a +12 volt

output when key is in accessory or ignition position. The output is 1 amp max, use relay when necessary. Insulate end if not

used. Warning! Do Not connect this wire to the vehicle’s accessory/ ignition wiring.

Operation:

If simulating VES:

Turn the radio on and press the MODE button to select DVD or VES.

1. Press the SEEK up or down button to select CHP 1 for Aux 1 or CHP for Aux 2.

Note: When the key is removed and the doors remain closed, the Radio will display DVD Paused or Power Off. The Aux source

audio will be muted during this time. This is a normal function for the factory radio. When the key is turned to Accessory or Ignition,

the Aux source audio will un-mute.

If simulating Satellite receiver: The radio will need to be updated with information prior to use. This is one time process and

will not need to be done again unless the radio is disconnected or vehicle battery is replaced/disconnected.

Turn the radio on and press the MODE button to select Satellite. On single disc radios (REF model), wait at least 1 minute before

using. Navigation (REC) or 6 Disc (RAQ or RAK) radios will display ‘UPDATING CHANNELS’, please wait until the information

disappears.

1. Press the SEEK up or down button to select Channel 1 for Aux 1 or Channel 2 for Aux 2.

Note: If you do not hear the audio source in aux mode, please check that the 3 pin connector is connected to the correct

connector on the 10 pin t-harness.

DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the AAI-CHY parts be held liable for consequential damages sustained in

connection with the AAI-CHY. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation

or liability in relation to the AAI-CHY other than its replacement.