Tyan B2723T15M User manual

B2723T15 /// Transport GX15

B2723T15M

Revision 1.0

part of this manual may be reproduced or translated without prior written

consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in

this manual are property of their respective owners including, but not limited to

the following.

TYAN, Tiger i7501 S2723, Transport B2723T15, Transport B2723T15M,

Transport GX15 are trademarks of TYAN Computer Corporation.

Intel, Xeon and combinations thereof are trademarks of Intel Corporation.

AMI, AMIBIOS are trademarks of AMI Software Incorporated.

Microsoft, Windows are trademarks of Microsoft Corporation..

QLogic, Zircon, and combinations thereof are trademarks of QLogic

Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer

Corporation and has been reviewed for accuracy and reliability prior to printing.

TYAN assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN products including liability or

warranties relating to fitness for a particular purpose or merchantability. TYAN

retains the right to make changes to product descriptions and/or specifications

at any time, without notice. In no event will TYAN be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

1

http://www.tyan.com

Table of Contents

Before you begin…

Chapter 1: Introduction

1.1 Congratulations

1.2 Hardware Specifications

1.3 Front View

1.4 Top View

Chapter 2: Hardware Installation

2.0 Installation Procedures

2.1 Opening the Chassis

2.2 Installing HDD

2.3 Installing Processor(s) and

heatsink(s)

2.4 Installing Add-on PCI Card

2.5 Installing Memory Modules

2.6 Installing Vent Duct

2.7 Finishing up

Chapter 3: Installing Into A Cabinet

or Telco Rack

3.0 Before you begin

3.1 Installing single system into a

19” cabinet

Chapter 4: Server Management Daughter

Card ( SMDC)

4.1 Summary

4.2 Features at a glance

4.3 Jumper setting

4.4 Specification

4.5 SMDC Features

4.6 Tyan System Operator (TSO)

summary

Appendix

Safety Document of system

Safety Document of SMDC

...……………………………………..Page 3

...……………………………………..Page 4

..….…………………………………..Page 5

...……………………………………..Page 6

.....………………………………… ..Page 7

...………………………………… ..Page 8

.…………………………………… ..Page 8

.…………………………………… ..Page 9

...………………………………… ..Page 10

...………………………………… ..Page 11

...………………………………… ..Page 12

...………………………………… ..Page 13

....…………………………………..Page 14

.....………………………………….Page 15

..……………………………………Page 16

..…..………………………………..Page 16

…...…..…………………………….Page 17

..………………………………..Page 18

….….….……..…………………….Page 18

..……..……………………………..Page 19

...……………………………………Page 20

…...…………………………………Page 20

….…………………………………..Page 25

…..………………………………….Page 31

…..………………………………….Page 32

.….………………………………….Page 32

.….………………………………….Page 33

2

http://www.tyan.com

Before you begin…

Check the box contents!

The barebone system package should contain the following:

1 x Tiger i7501 (S2723) motherboard (preinstalled)

2 sets x CPU retentions and clips

2 x Xeon Heatsink

1 x ATA 100 cable for HDD (pre-installed)

1 x Vent duct

2 x power cords (1 x compatible for standard US voltage, 1 x

compatible for standard German voltage)

1 x Tiger i7501 (S2723) User’s Manual

1 x Transport B2723T15/B2723T15M User’s Manual

1 x Tiger i7501 (S2723) Quick Reference

1 x TYAN driver CD

1 x screw

1x Tyan M3289 SMDC (optional item for B2723T15M)

1x 50-pin SMDC cable (optional item for B2723T15M)

If any of these items are missing, please contact your vendor/dealer for replacement

before continuing with the installation process.

3

http://www.tyan.com

Chapter 1: Introduction

1.1 – Congratulations!

Thank you for choosing the TYAN B2723T15/B2723T15M, the most compact Dual

Intel

®

Xeon processor platform for flexibility and productivity. Based on Intel’s E7501

chipset, this powerful system is Hyper-Threading ready - utilizing onboard resources

so that a second thread of data can be processed in a single processor. Special

features of this system include IPMI Server Management, PCI-X support, one

10/100/1000 and one 10/100 Ethernet ports and onboard video.

Remember to visit TYAN’s Website at http://www.tyan.com

. There you can find

information on all of TYAN’s products with FAQs, distributors list and BIOS setting

explanations.

4

http://www.tyan.com

1.2 – Hardware Specifications

Form Factor:

• Optimized 1U form factor

• 14.5” inch in depth

• Dimensions (W x H x D):

482.6mm x 44mm x368.3mm

(19” x 1.73” x 14.5”)

Drive bays:

• 1 x internal 3.5” drive bay

Cooling Fans:

• 3 pcs 40x40x28 mm system fans with

tachometer monitoring

• Specially-designed CPU fan duct

Switch and LED Indicators:

• 1 x power switch

• 1 x reset switch

• 1 x power LED

• 1 x HDD LED

PSU:

• 300W EPS12V PSU (w/ active PFC)

System board:

• Tyan Tiger i7501 (S2723GNN)

Processor

• Dual mPG604 ZIF Socket

• Supports up to 2 x Intel

®

XEON

processors with 512KB of integrated L2

cache

• Supports processor speed up to 2.8GHz

• Front-Side Bus support for 533MHz

Chipset

• Intel

®

E7501 server chipset

• MCH + ICH3 + P64H2 + FWH

I/O Expansion

• 1x PCI-X expansion slot on riser card

Memory

• Four 184-pin 2.5-Volt DDR DIMM

sockets

• Supports up to 8GB of Registered DDR

RAM

• Supports only Registered ECC type

memory modules

Integrated LAN

• Two RJ-45 LAN Connectors with LEDs

• One 10/100

• One 10/100/1000

Server Management Daughter Card

(Option)

• Tailored for IPMI highest 1.5

specifications

• Supports flexible Windows and Linux

based

Management Solution

• Supports remote Power on/off and reset

support (IPMI-over-LAN)

BIOS

• AMI BIOS 8.0 on 4Mbit Flash ROM

• LAN remote boot (PXE) and SMBIOS

v2.3 support

• BIOS Boot Specification v3.1(BBS)

support

• Auto configuration of IDE hard disk

types

Regulatory

• FCC Class A certified

• European CE certified

(Declaration of Conformity)

Packing information

• Barebone weight: 11 kg

• Complete system weight: 11.5 kg

TYAN reserves the right to add support

or discontinue support for any OS

without notice.

5

http://www.tyan.com

1.3 – Front View

Powe

r

/HDD

LEDs

Power/

Reset

Switches

PS/2 Mouse and Keyboard

Double-deck USB 1.1 Port

A

dd-on PCI

Expansion Slot

Fast Ethernet w/ LED

VGA Port

Serial Port

Gigabit Ethernet w/ LED

6

http://www.tyan.com

1.4– Top View

Cooling Fans

CPU 2

EPS 12V

PSU

CPU 1

HDD

Riser card

Memory

Slots

SMDC

( Server

Management

Daughter Card)

7

http://www.tyan.com

Chapter 2: Hardware Installation

2.0 Introduction

You are now ready to install your system.

The first thing you should do is read this user’s manual. It contains important

information that will make installation and setup much easier. Here are some

precautions you should take when installing your system:

(1) Ground yourself properly before removing the top cover of the system. Unplug

the power from your computer power supply and then touch a safely grounded

object to release static charge (i.e. power supply case). For the safest

conditions, Tyan recommends wearing a static safety wrist strap.

(2) Avoid touching the motherboard components, IC chips, connectors, memory

modules, and leads.

(3) Motherboard is pre-installed in the system, if, under any circumstances, it is

removed from the system, place the motherboard on a grounded antistatic

surface.

(4) Inspect the board and system for damage.

The following pages include details on how to install the processor, memory, disk drive

and cables.

NOTE

DO NOT APPLY POWER TO THE SYSTEM IF ANY PART OF THE

SYSTEM COMPONENTS HAS BEEN DAMAGED

8

http://www.tyan.com

2.1 Opening the chassis

2.1.1 Push the top cover toward back.

2.1.2 Lift up the top cover and remove it

from the chassis.

2.1.3 Top cover removed.

9

http://www.tyan.com

2.2 Installing HDD

2.2.1 Slide the HDD into place.

2.2.2 Connect the Power cable to HDD.

2.2.3 Connect ATA cable to HDD.

Note: ATA cable is pre-connected to M/B (J23).

2.2.4 Secure the drive with 4 screws from

the bottom of the chassis.

10

http://www.tyan.com

2.3 Installing Processor (s) and Heatsink(s)

2.3.1 Lift the lever on the CPU socket until

it is approximately 130

o

or as far

back as possible to the socket.

2.3.2 Align the processor with the socket.

There are keys underneath the

processor just like on memory

modules to ensure that they insert

the correct way.

2.3.3 Seat the processor firmly into the

socket by gently pressing down until

the processor sits flush with the

socket.

2.3.4 Place the socket lever back down

until it snaps into place.

2.3.5 Your processor is installed

2.3.6 Repeat these steps for any

additional processors if you are

using more than one processor.

2.3.7 Seat heatsinks between brackets

(pre-installed) on the processor and

attach heatsinks clips to secure.

11

http://www.tyan.com

2.4 – Installing Add-on PCI Card

2.4.1 Loosen the screw and remove PCI slot

cover.

2.4.2 Plug your PCI/PCI-X add-on card into

the PCI socket slot on the riser card.

2.4.3 Secure Add-on card by tightening the

screw from the side.

12

http://www.tyan.com

2.5 Installing Memory Modules

Note: Please make sure to read through M/B User’s Manual before your

start installing memory modules.

2.5.1 Insert the DIMM modules into the

memory slots, starting with memory

slot B1+B2 or A1+A2.

2.5.2 Press down on the memory modules

until it locks into place.

2.5.3 The B2723T15/B2723T15M requires

that memory modules be installed IN

PAIRS. Please refer to S2723/Tiger

i7501 M/B User’s Manual page

16~18 for exact details.

2.5.4 To ensure thermal performance,

LOW PROFILE memory modules are

recommended.

13

http://www.tyan.com

2.6 Installing Vent Duct

2.6.1 Attach the vent duct on the CPU area.

2.6.2 Place the vent duct on the top of CPU

area, in between the capacitors as

shown in pictures.

14

http://www.tyan.com

2.7 Finishing Up

2.7.1 Put the top cover back on and fasten

the thumb screws in the back of the

chassis.

Congratulations on making it this far! You’re finished setting up the hardware aspect of

your computer. Before closing up your chassis, make sure that all cables and wires are

connected properly, especially IDE cables and most importantly, jumpers. You may

have difficulty powering on your system if the motherboard jumpers are not set

correctly. For detailed M/B jumper settings, please refer to S2723/ Tiger i7501 M/B

user’s manual.

In the rare circumstance that you have experienced difficulty, you can find help by

asking your vendor for assistance. If they are not available for assistance, please find

setup information and documentation online at our website or by calling your vendor’s

support line.

15

http://www.tyan.com

Chapter 3: Installing Into A 19” Cabinet/ Telco Rack

3.0 Before you begin ….

The system is both light and easy-to-install into cabinets and racks, so we suggest that

you use the mounting brackets (on both sides of the system) to directly attach and

secure this rackmount system.

Should you still prefer to have rails in order to slide the system in and out from the

cabinet, you may purchase a separate rail kit from Tyan. Please contact your local

Tyan office for more details.

Note:

1. When installing two systems back-to-back, please choose:

a. 19” cabinet of 1000mm and above in depth.

b. 4-post telco rack (open-air rack).

16

http://www.tyan.com

3.1 Installing system into a cabinet or telco rack

3.1.1 Place the system between the poles

inside the cabinet.

3.1.2 Secure the system to the desired

location using screws provided by

cabinet manufacturer.

3.1.3 Finished look.

17

http://www.tyan.com

Chapter 4: Server Management Daughter Card / SMDC

(pre-installed in B2723T15M)

Warning:

DO NOT INSERT SMDC INTO ANY PCI SLOT.

4.1 – Summary

The Tyan Server Management Daughter Card (SMDC) is a powerful yet cost-efficient

solution for high-end server management hardware packages. The SMDC provides

remote system monitoring and control even when the operating system is absent or

simply fails, and empowers server boards with advanced industry standard features. It

effectively enables IT Managers to have remote and multi-interface access to monitor,

control, and diagnose activities.

The Tyan SMDC is powered by an intelligent controller known as the Baseboard

Management Control (BMC). The BMC is a standalone mini-CPU that runs on its own

Real Time Operating System (RTOS) to complete a variety of tasks. Backed by

QLogic’s reliable ARM7 technology, systems are consistently monitored and supported.

Unlike regular cards such as AGP cards, network cards or SCSI cards, the SMDC is

not a peripheral card that requires any hardware specific driver. As long as standby

power supports the system, the SMDC will monitor the system.

The Tyan SMDC provides many diverse methods to communicate with the hardware.

There is flexibility to choose among Keyboard Controller Style (KCS), Block Transfer

(BT) style, Intelligent Platform Management Bus (IPMB), Emergency Management Port

(EMP) and standard IPMI-Over-LAN communication as defined in latest IPMI 1.5

specification. The Tyan SMDC is compatible with all IPMI-compliant software as well

as with the Tyan System Operator™ (TSO) software package. The SMDC hardware is

OS-dependent and is fully compatible with all major Operating Systems.

18

http://www.tyan.com

4

.2 – Features at a Glance

Feature Description

BMC QLogic Zircon V2 based on ARM7 technology

IPMI Version 1.5 Spec

FRU “Field Replaceable Unit” Information Storage

SDR Sensor Data Record

SEL Sensor Event Log

GPIO “General Purpose Input and Output” lines for future expansion.

IPMB Intelligent Platform Management Bus

EMP Emergency Management Port

RTC Real Time Clock

IPMI-Over-LAN Remote sensor monitor, host control and system diagnose

Remote Host

Control

Power up, down, reset, power cycle or NMI through LAN port

Remote Sensor

Monitor

SMDC provides sensor information as long as BMC receives

enough operating power.

Remote

Diagnostic

SMDC allows for system diagnostic when the system is not in

operation (either intentionally or accidentally) through remote IPMI

command execution.

BMC Firmware

Update

SMDC supports onboard update of the BMC firmware.

ASF Alert Standard Forum

TSO Tyan System Operator™

19

http://www.tyan.com

4.3 – Jumper Setting

Label Header Type/Part Description Pin Layout

J1 HDR25X2_SVM_A SVM Edge

Connector A

Reserved

Pin 1 GND J10 HDR2 Zircon Firmware

Reset

Pin 2 BMC_RESET#

Pin 1 DCD

Pin 2 RXD

Pin 3 TXD

Pin 4 No Connection

Pin 5 GND

Pin 6 No Connection

Pin 7 RTS

Pin 8 CTS

Pin 9 RI

J28 HDR5X2 UART /

Emergency

Management Port

Pin 10 No Connection

Pin 1 SDA

Pin 2 GND

Pin 3 SCL

J41 HDR4X1 BMC Private I

2

C

Pin 4 5VSB

4.4 – Specifications

The following specifications are described below in detail.

Hardware Monitoring

Protocol and Standard

Auxiliary Communication Interface

Auxiliary SMBus / I

2

C buses

Teamed with other IPMB Devices (PMCs and EMCs)

Remote Monitor, Control and Diagnostics

Sensor Repository

System Event Log

Field Replaceable Unit Information Storage

Emergency Management Port Console

Real Time Clock

Upgrade firmware

Front Panel LED and Buzzer

“Always Ready”

TYAN System Operator ™ (TSO)

OEM Drivers

20

http://www.tyan.com

Page is loading ...

Tyan B2723T15M User manual

This manual is also suitable for

Tyan B2723T15M User manual

Related papers

Other documents