Horizon Fitness CLUB E800 User manual

Category
Fitness, gymnastics & weight training
Type
User manual

This manual is also suitable for

CLUB SERIES
ELLIPTICAL USERS GUIDE
FOR MODELS :
E500
E700
E800
BEFORE
YOU BEGIN
ASSEMBLYASSEMBLY
3
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
INTRODUCTION
CONGRATULATIONS and THANK YOU for your purchase of this Horizon Club elliptical!
Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, a Horizon Club elliptical can
help you attain it adding club-quality performance to your at-home workouts, with the ergonomics
and innovative features you need to get stronger and healthier, faster. Because we're committed to
designing fitness equipment from the inside out, we use only the highest quality components. It's a
commitment we back with one of the strongest frame-to-brake warranty packages in the industry.
You want exercise equipment that offers the most comfort, the best reliability and the highest quality
in its class.
The Horizon Club Ellipticals deliver.
INTRODUCTION
TABLE OF CONTENTS
Important Precautions
Assembly
Before You Begin
Elliptical Operation
Conditioning Guidelines
Troubleshooting & Maintenance
Limited Warranty
CONTACT INFORMATION
4
5
17
18
35
39
43
Back Panel
BEFORE
YOU BEGIN
4
INTRODUCTION ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
ASSEMBLY
IMPORTANT
PRECAUTIONS
SAVE THESE INSTRUCTIONS
Read all instructions before using this elliptical. When using an electrical product, basic precautions
should always be followed, including the following: Read all instructions before using this elliptical. It is the
responsibility of the owner to ensure that all users of this elliptical are adequately informed of all warnings
and precautions. If you have any questions after reading this manual, contact Customer Tech Support at
the number listed on the back panel of this manual.
IMPORTANT PRECAUTIONS
At NO time should pets or children under the age of 12 be closer to the elliptical than 10 feet.
At NO time should children under the age of 12 use the elliptical.
Children over the age of 12 should not use the elliptical without adult supervision.
It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been
exposed to colder temperatures or high moisture climates, it is strongly recommended that the elliptical is
warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.
To reduce the risk of burns, fire, electrical shock or injury to persons:
If you experience any kind of pain, including, but not limited to chest pains, nausea, dizziness, or
shortness of breath, stop exercising immediately and consult your physician before continuing.
Maintain a comfortable pace. Do not sprint above 80 rpms on this machine.
To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or
dismounting the machine.
Do not wear clothes that might catch on any part of the elliptical.
Do not turn pedal arms by hand.
Make sure handlebars are secure before each use.
Do not insert or drop any object into any opening.
• Unplug elliptical before moving or cleaning it. To clean, wipe surfaces down with soap and slightly damp
cloth only; never use solvents. (See MAINTENANCE page 38)
This elliptical should not be used by persons weighing more than 275 pounds on the E500 and 300
pounds on the E700 and E800. Failure to comply will void the warranty.
• This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school
or institutional setting. Failure to comply will void the warranty.
Do not use elliptical in any location that is not temperature controlled, such as but not limited to garages,
porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty.
Use the elliptical only as described in this manual.
Keep the topside of the foot support clean and dry
Care should be taken when mounting or dismounting the equipment. First bring the elliptical to a full
stop. Second, carefully rotate one footpad to its lowest position. Third, mount or dismount from this side
of the elliptical.
Disconnect all power before servicing the equipment.
WARNING
BEFORE
YOU BEGIN
ASSEMBLY
5
INTRODUCTION
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ASSEMBLY
IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!
There are several areas during the assembly process of a elliptical that special attention must be paid. It is
very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened.
If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not
tightened and will seem loose and may cause irritating noises. To prevent damage to the elliptical, the
assembly instructions must be reviewed and corrective actions should be taken.
UNPACKING
Unpack the product where you will be using it. Place the product on a level flat surface. It is recommended
that you place a protective covering on your floor. During each assembly step, ensure that ALL nuts and
bolts are in place and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium
bike grease is recommended.
Before proceeding, find your elliptical’s serial number
located on the front stabilizer tube and enter it in the
space provided below. Also locate the model name
which is located on the side cover badge.
ENTER YOUR SERIAL NUMBER AND
MODEL NAME IN THE BOXES BELOW:
SERIAL NUMBER :
MODEL NAME:
* Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
* Also enter this serial number on your Warranty Card.
WARNING
IMPORTANT
PRECAUTIONS
BEFORE
YOU BEGIN
6
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
TOOLS INCLUDED PARTS INCLUDED
c 5mm Allen Wrench
c Phillips Screw Driver
c 13/15mm Flat Wrench
c 1 Console
c 1 Console Mast
c 1 Front Stabilizer Tube
c 2 Upper Handlebars
c 2 Lower Handlebars
c 2 Lower Link Arms
c 2 Pivoting Foot Pads
CONSOLE (E700/E800 SHOWN)
UPPER HANDLEBAR
MAIN FRAME
LOWER HANDLEBAR
LOWER LINK ARM
FRONT STABILIZER TUBE
GRIP PULSE
CONSOLE MAST
PIVOTING FOOT PADS
(E800 SHOWN)
PEDAL ARM
c 1 Top Cover
c 1 Top Cover Grommet
c 6 Hardware Bags
c 1 Water Bottle Cage
c 1 HORIZON FITNESS
12-volt Power Supply
c 1 Audio Adaptor Cable
(E700 & E800 only)
WATER BOTTLE CAGE
MP3 STORAGE
SPEAKERS (E700/E800 ONLY)
E800 SHOWN
If you have questions or if there are any missing parts, contact Customer Tech Support.
Contact information is located on the back panel of this manual.
For a complete exploded diagram, visit us at www.horizonfitness.com
TOP COVER
BEFORE
YOU BEGIN
ASSEMBLY
7
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
MAIN FRAME
FRONT STABILIZER TUBE
SCREW (A)
ASSEMBLY STEP 1
A) Open HARDWARE BAG FOR STEP 1.
B) Attach the FRONT STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A).
SCREW (A)
20 mm
Qty: 2
HARDWARE BAG FOR STEP 1 CONTENTS :
BEFORE
YOU BEGIN
8
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
ASSEMBLY STEP 2
MAIN FRAME
REAR STABILIZER
BOLT (A)
SPRING WASHER (B)
FLAT WASHER (C)
SCREW (B)
A) Open HARDWARE BAG FOR STEP 2.
B)
Secure
REAR STABILIZER
to
MAIN FRAME
using 2
SCREWS (B).
NOTE: Make sure holes are aligned before inserting SCREWS.
SCREWS (B)
30 mm
Qty: 4
HARDWARE BAG FOR STEP 2 CONTENTS :
BEFORE
YOU BEGIN
ASSEMBLY
9
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
CONSOLE WIRES
TOP COVER
CONSOLE MAST
GROMMET
MAIN FRAME
BOLTS (C)
LOCK WASHERS (D)
ASSEMBLY STEP 3
A) Open HARDWARE BAG FOR STEP 3.
B) Slide the GROMMET and TOP COVER over the CONSOLE MAST.
C)
Carefully pull the CONSOLE WIRES through the CONSOLE MAST using the twist tie located inside the
CONSOLE MAST.
D) Attach
CONSOLE MAST
to
MAIN FRAME
using 7 BOLTS (C) and 7 LOCK WASHERS (D)
.
E) Slide GROMMET and TOP CAP down to seal the MAIN FRAME.
BOLTS (C)
15 mm
Qty: 7
LOCK WASHER (D)
13.5 mm
Qty: 7
HARDWARE BAG FOR STEP 3 CONTENTS :
* NOTE: Be careful not to
pinch any wires while
assembling the mast.
BEFORE
YOU BEGIN
10
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
ASSEMBLY STEP 4
NOTE: There is NO hardware bag for this step.
A) Slide LOWER HANDLEBAR onto CONSOLE MAST and align NOTCH with TAB making sure bars are joined
together completely. Secure LOWER HANDLEBAR to CONSOLE MAST using
PRE-ATTACHED SET SCREWS.
B) Slide UPPER HANDLEBAR onto CONSOLE MAST and align NOTCH with TAB making sure bars are joined
together completely. Secure UPPER HANDLEBAR to CONSOLE MAST using PRE-ATTACHED SET SCREWS.
C) Repeat on other side.
After handlebars are assembled they will rotate freely – be cautious. Until the
machine is fully assembled, do not grab the handlebars for support.
WARNING
PRE-ATTACHED SCREWS
TAB
UPPER HANDLEBAR
HANDLEBAR JOINT
LOWER HANDLEBAR
NOTCH
BEFORE
YOU BEGIN
ASSEMBLY
11
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ASSEMBLY STEP 5
HARDWARE BAG FOR STEP 5 CONTENTS :
STEP 5
A) M5x20mm Screw
quantity:4
B) M5x15mm Screw
quantity:8
quantity:6
D) M8x15mm Screw
quantity: 2
C) 29mm wave washer
SCREW (E)
LOWER LINK ARM
FOOTPAD
A) Open HARDWARE BAG FOR STEP 5.
B) Attach FOOTPAD to LOWER LINK ARM using 4 SCREWS (E).
C) Repeat on other side.
E800 SHOWN
BEFORE
YOU BEGIN
12
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
ASSEMBLY STEP 6
A) M5x20mm Screw
quantity:4
B) M5x15mm Screw
quantity:8
quantity:6
D) M8x15mm Screw
quantity: 2
C) 29mm wave washer
FOOTPADWASHER (F)SCREW (G) FOOTPAD BRACKET
PEDAL ARM
LINK ARM
A) Open HARDWARE BAG FOR STEP 6.
B) Place WASHER (F) over the LINK ARM axle.
C) Slide LINK ARM into PEDAL ARM.
D) Attach FOOTPAD BRACKET to the LINK ARM with 3 SCREWS (G).
E) Repeat on other side.
SCREW (E)
20 mm
Qty: 4
SCREW (F)
15 mm
Qty: 8
WAVE WASHER (F)
20 mm
Qty: 2
SCREW (G)
15 mm
Qty: 6
HARDWARE BAG FOR STEP 6 CONTENTS :
E800 SHOWN
BEFORE
YOU BEGIN
ASSEMBLY
13
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ASSEMBLY STEP 7
STEP 5
A) M5x20mm Screw
quantity:4
B) M5x15mm Screw
quantity:8
quantity:6
D) M8x15mm Screw
quantity: 2
C) 29mm wave washer
LOWER HANDLEBAR
SPACER RING (G)
SPACER (H)
BOLT (I)
WASHER (K)
NUT (J)
LOWER LINK ARM
SPACER
SPACER RINGS
LOWER
HANDLEBAR
A) Open HARDWARE BAG FOR STEP 7.
B) Insert SPACER (H) into the LOWER HANDLEBAR. Place SPACER RINGS (G) on both sides of SPACER (H), slide
LOWER LINK ARM into bottom end of LOWER HANDLEBAR.
C) Insert BOLT (I) into LOWER HANDLEBAR and secure using NUT (J) and WASHER (K).
D) Repeat on other side.
SPACER RING (G)
Qty: 4
SPACER (H)
Qty: 2
BOLT (I)
45 mm
Qty: 2
NUT (J)
Qty: 2
WASHER (K)
Qty: 2
HARDWARE BAG FOR STEP 7 CONTENTS :
BEFORE
YOU BEGIN
14
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
ASSEMBLY STEP 8
CONSOLE WIRES
CONSOLE
PRE-ATTACHED SCREWS
NOTE: There is NO hardware bag for this step.
A) Attach CONSOLE MAST WIRES to the CONSOLE WIRES.
B) Carefully tuck the CONSOLE MAST WIRES into the CONSOLE MAST.
C) Attach CONSOLE onto CONSOLE MAST using the 4 PRE-ATTACHED SCREWS.
NOTE: Be careful not to pinch any wires while assembling the console.
BEFORE
YOU BEGIN
ASSEMBLY
15
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ASSEMBLY STEP 9
WATER BOTTLE CAGE
PRE-ATTACHED SCREWS
NOTE: There is NO hardware bag for this step.
A) Attach WATER BOTTLE CAGE onto CONSOLE MAST using PRE-ATTACHED SCREWS.
BEFORE
YOU BEGIN
16
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
YOURE FINISHED!
E800
E700
E500
BEFORE
YOU BEGIN
ASSEMBLY
17
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
BEFORE
YOU BEGIN
ASSEMBLY
BEFORE YOU BEGIN
CONGRATULATIONS! on choosing your elliptical. You’ve taken an important step in developing and
sustaining an exercise program! Your elliptical is a tremendously effective tool for achieving your personal
fitness goals. Regular use of your elliptical can improve the quality of your life in so many ways.
HERE ARE JUST A FEW OF THE HEALTH BENEFITS OF EXERCISE:
Weight Loss
A Healthier Heart
Improved Muscle Tone
Increased Daily Energy Levels
The key to reaping these benefits is to develop an exercise habit. Your new
elliptical will help you eliminate obstacles that prevent you from exercising.
Inclement weather and darkness won't interfere with your workout when you
use your elliptical in the comfort of your home. This guide provides you with
basic information for using and enjoying your new machine.
LOCATION OF THE ELLIPTICAL
Place the elliptical on a level surface. There should be 6 feet of clearance
behind the elliptical, 3 feet on each side and one foot in front for the power
cord (See diagram to the right). Do not place the elliptical in any area that
will block any vent or air openings. The elliptical should not be located in a
garage, covered patio, near water or outdoors.
GFFU
GFFU
GFFU
GPPU
BEFORE
YOU BEGIN
18
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
ASSEMBLY
ELLIPTICAL
OPERATION
POWER
Your programmable elliptical is powered by a power supply. The power must be plugged into the power jack,
which is located in the front of the machine near the STABILIZER TUBE. Make sure the power switch on the
console is in the ON position. Note: Not all units have an ON/OFF switch on the console.
Do not operate the elliptical if the power cord or plug is damaged.
If the elliptical appears to not be working properly, do not use the elliptical.
MOVING
Your elliptical has a pair of transport wheels built
into the FRONT STABILIZER TUBE. To move, first
remove the power supply and firmly grasp the
CONSOLE MAST, carefully tilt and roll.
Our ellipticals are well built and heavy, weighing up to 200 lbs! Use care and
additional help if necessary when moving.
FOOT POSITIONING
Your elliptical offers a variety of foot positions. Moving your foot to the forward most position of the foot pad
increases your step height, which will create a feel similar to a step machine. Placing your foot toward the back
of the foot pad decreases your step height and creates more of a gliding feel, similar to a smooth walk or run.
Your elliptical also allows you to pedal both forward and backwards to offer a variation to your workout and to
focus on other major leg muscle groups such as your hamstrings and calves.
ELLIPTICAL OPERATION
WARNING
WARNING
BEFORE
YOU BEGIN
ASSEMBLY
19
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ELLIPTICAL
OPERATION
ASSEMBLY
E500 CONSOLE DISPLAY
Note: There is a thin protective sheet of clear plastic on the overlay of the console and should be removed.
A) LED DISPLAY WINDOWS: Displays: Time, Distance, Speed / Resistance and Calories / Pulse.
B) START: Press to start your workout.
C) STOP/PAUSE: Press to stop/pause/end your workout. Hold for 3 seconds to reset the elliptical.
D) WORKOUT QUICK KEYS: Used to select your workout.
E) WORKOUT SETTING / ENTER KEYS: Used to adjust workout settings and set your workout.
F) PRESS TO BEGIN KEY: Used to start your program.
G) UP/DOWN ARROW KEYS: Used to adjust resistance.
H) eTRAK™ PERFORMANCE TRACKING BUTTON: Used to scroll through accumulated personal data.
I) READING RACK: Holds reading material.
J) MP3 PLAYER POCKET: Holds MP3 player.
H
A
D
G
B
E
F
G
C
I
J
P
E
R
F
O
R
M
A
N
C
E
T
R
A
C
K
I
N
G
T IM E
D IS T A N C E
CU RRE NT WORK OUT LA ST WOR KOUT
AVE RAGE WO RKO UT LIF ETIM E T OTAL
C A L OR I ES / PU L SE
S P E ED / R E S IS T A NC E
P R E S S T O S W I T C H
H O R I Z O N C L U B
S T A R T
Q U I C K S TAR T
S T O P
H O L D T O R E SE T
A D J U S T R E S I S T A N C E
BEFORE
YOU BEGIN
20
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
ASSEMBLY
ELLIPTICAL
OPERATION
Simply press the START key to begin working out.
CONSOLE OPERATIO N
QUICK START
P1: MANUAL
Allows you to adjust the resistance level to your preference, without a preset program.
P2 - P3: WEIGHT LOSS WORKOUTS
Promotes weight loss by raising and lowering the resistance level, while keeping you in your fat burning zone.
P4 - P5: CARDIO STRIDE WORKOUTS
Creates an intense cardio workout with challenging combinations of resistance.
P6 - P7: POWER STRIDE WORKOUTS
Enhances your strength, speed and endurance by increasing resistance at specific intervals.
PROGRAM PROFILES
BEFORE
YOU BEGIN
ASSEMBLY
21
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ELLIPTICAL
OPERATION
ASSEMBLY
Note: There is a thin protective sheet of clear plastic on the overlay of the console and should be removed.
A) LED DISPLAY WINDOWS: Displays: Time, Distance, Speed / Resistance, Clock / Date and Calories / Pulse.
B) START: Press to start your workout.
C) STOP/PAUSE: Press to stop/pause/end your workout. Hold for 3 seconds to reset the elliptical.
D) USER 1 / USER 2: Used to select which user’s eTRAK™ data to activate, access and update.
E) WORKOUT QUICK KEYS: Used to select your workout.
F) WORKOUT SETTING / ENTER KEYS: Used to adjust program settings and set your program.
G) PRESS TO BEGIN KEY: Used to start your workout.
H) RESISTANCE KEYS: Used to reach desired resistance more quickly.
I) UP/DOWN ARROW KEYS: Used to adjust resistance.
J) eTRAK™ PERFORMANCE TRACKING BUTTON: Used to scroll through accumulated personal data.
K) MP3 PLAYER POCKET: Holds MP3 player.
L) READING RACK: Holds reading material.
M) AUDIO SPEAKERS: Transmits sound from your CD / MP3 device.
N) AUDIO IN JACK: Used to play sound from CD / MP3 device through speakers using the included audio
adaptor cable.
O) AUDIO OUT / HEADPHONE JACK: Used to run sound into your head phones.
E700-E800 CONSOLE DISPLAY
M M
T I M E
D I S T AN C E
CURRENT WORKOUT WEEKLY GOAL MONTHLY TOTAL
LAST WORKOUT WEEKLY TOTAL LIFETIME TOTAL
C L O C K / D A T E
H O R I Z O N C L U B
P
E
R
F
O
R
M
A
N
C
E
T
R
A
C
K
I
N
G
C A L OR I ES / P U L SE
S P E ED / R ES I S T A N C E
P R E S S T O S W I T C H
20
18
16
14
1210
8
6
4
2
S T A R T
Q U I C K S TART
S T O P
H O L D T O R E SE T
A D J U S T R E S I S T A N C E
J
A
D
H
I
B
F
G
E
I
C
L
KN O
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43

Horizon Fitness CLUB E800 User manual

Category
Fitness, gymnastics & weight training
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI