Wyrestorm TX-SW-0201 Quick start guide

Wyrestorm
Brand
Wyrestorm
Model
TX-SW-0201
Category
Video splitters
Type
Quick start guide

Wyrestorm TX-SW-0201 is an auto-switching HDBaseT transmitter designed to send VGA or HDMI signals to a device with integrated HDBaseT receiving capability, such as a display or projector, over distances of up to 100m/328ft (4K - 70m/230ft). Perfect for small meeting room or classroom environments, the TX-SW-0201 supports video resolutions up to 4096 x 2160 @ 30Hz (4K) for HDMI and up to 1920 x 1200 for VGA. It also supports 3D Blu-ray and satellite/cable interlaced stereoscopic formats. With its 12V DC 1A power supply, the TX-SW-0201 consumes a maximum of 35W of power.

Wyrestorm TX-SW-0201 is an auto-switching HDBaseT transmitter designed to send VGA or HDMI signals to a device with integrated HDBaseT receiving capability, such as a display or projector, over distances of up to 100m/328ft (4K - 70m/230ft). Perfect for small meeting room or classroom environments, the TX-SW-0201 supports video resolutions up to 4096 x 2160 @ 30Hz (4K) for HDMI and up to 1920 x 1200 for VGA. It also supports 3D Blu-ray and satellite/cable interlaced stereoscopic formats. With its 12V DC 1A power supply, the TX-SW-0201 consumes a maximum of 35W of power.

HDBaseT™ 4K Transmitter with HDMI / VGA Auto-Switch
TX-SW-0201
Quickstart Guide
In the Box
1 x TX-SW-0201 Transmitter
1 x 12V DC 1A Power Supply
1 x 3-pin Screw Down Phoenix Connector
Front Panel
VGA Input 15-pin VGA VESA (D-SUB 15): Connect to D-SUB
15 VGA output of device such as a computer.
HDMI Input 19-pin type A HDMI female digital video/audio input:
Supports HDMI and DVI/D (requires adapter-not
included) Limited to 275 MHz pixel clock.
Audio In 3.5 mm (1/8 in) Stereo Analog Audio: Connect to
audio output of device connected to VGA input.
Rear Panel
Update 3-pin Screw Down Phoenix Connector: Used for
updatingtransmitterrmware
Status LED Solid - Link to receiver has been established.
Flashing - Link to receiver has not been established.
See Troubleshooting.
UTP Out 8-pin RJ-45 female: Connect to an HDBaseT
receiver. See HDBaseT Wiring for wiring details.
12V DC In 12V DC 1A: Connect to supplied power supply.
Power LED Illuminates when DC power is applied.
A
A
B
B
D
C
C
E
A
B C
A
B C D E
TX-SW-0201 Front
TX-SW-0201 Rear
Basic Wiring Diagram & Installation
IMPORTANT! Do not connect or disconnect (hot plug) the VGA,
HDMI, or HDBaseT connections while the transmitter is powered
on. Doing so may cause damage to the transmitter or connected
devices.
1. InstalltheTX-SW-0201inonasolidatsurfacesuchasacabinetor
rack shelf located in a dry, well ventilated area.
Tip: WyreStorm recommends using the mounting brackets (not
included) whenever possible to avoid the transmitter from moving
due to cabinet vibrations.
2. Connect an HDMI source to the HDMI In on the transmitter using an
HDMI cable from a high quality brand such as WyreStorm Express.
3. Connect a VGA source to the VGA In on the transmitter.
4. Terminate a cable per the HDBaseT Wiring section and connect to
the UTP Out on the transmitter.
5. Connect the opposite end of the HDBaseT cable to a WyreStorm
HDBaseT receiver, switcher, or 3rd party display device with built-in
HDBaseT receiver.
6. Connect the power supply to the 12V DC input on the transmitter.
HD TV / Projector with built-in receiver
or HDBaseT Receiver (not shown)
KEY
HDMI
HDBaseT Cat5e/6
VGA Video
Analog Audio
Power
Auto-switching HDBaseT™ transmitter for sending a VGA or HDMI signal to a device with integrated HDBaseT receiving capability such as a display or
projector 100m/328 ft (4K - 70m/230ft) away. Perfect for small meeting room or classroom environments.
VGA Video
12V DC 1A
HDMI
Video / Audio
Mains
Power
HDMI Source
VGA Source
HDBaseT
Cat5e/6
Analog Audio
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
TX-SW-0201 Quickstart Guide | 150908
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
1 of 2
Wiring and Connections
HDBaseT Wiring
Wiring for HDBaseT follows the EIA T568B standard.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables,
andelectricalorenvironmentalinterferencecanhaveanadverseeect
on HDBaseT transmission limiting performance. Steps should be taken
to minimize these factors (or remove completely) during installation for
best results.
Supported Video Resolutions
Thesupportedresolutionatthedisplayisaectedbycabletypeand
distance between the transmitter and receiving device.
Note: When connected to a class B HDBaseT receiver, the
supported resolution is limited to 70m/230ft 1080p.
Cable Type Range Supported Resolution
Cat5e/6
100m/328ft
1080p @ 60Hz 36bit
1080p @ 60Hz 48bit
1080p @ 60Hz 3D
70m/230ft 3840 x 2160 @ 30Hz 4:4:4
Cat6a/7 100m/328ft
1080p @ 60Hz 36bit
1080p @ 60Hz 48bit
1080p @ 60Hz 3D
4096x2160@30Hz 4:4:4
Audio and Video
Audio Formats Up to 7.1 DTS Master HD and Dolby True
HD
Video Resolution HDMI: Up to 4096 x 2160 @ 30Hz (4K)
VGA: Up to 1920 x 1200
3D Support Blu-ray: Frame packing/sequential
Satellite/Cable: Interlaced stereoscopic
Power
Input Power 12V DC 1A
Max Power Consumption 35W
Dimensions and Weight
Height 0.98 in / 25 mm
Width 4.25 in / 108 mm
Depth 4.20 in / 106.7 mm
Weight 0.34 lbs. / 0.75 kg
Environmental
Operating Temperature 32°F ~ 113°F (0°C ~ 45°C) 10% ~ 90%,
non-condensing
Storage Temperature -4°F ~ 140°F (-20°C ~ 70°C) 10% ~ 90%,
non-condensing
Regulatory
Safety and Emission CE | FCC
RoHS Compliant
Specications
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is connected to the transmitter and receiving device. If
using a display with a built in receiver, verify that the device is powered
On.
• Verify that the transmitter supports the output resolution of the source.
See Supported Video Resolutions.
• Verify that the receiving device and display support the output resolution
of the source. Lower the resolution of the source to verify output on the
display. If transmitting 3D or 4K, verify that the HDMI cables used are
3D or 4K rated.
• Verify that the HDBaseT cable is properly terminated per the HDBaseT
Wiring section.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
Tip: WyreStorm recommends using a cable tester or connecting the
cable to others devices to verify functionality.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
TX-SW-0201 Quickstart Guide | 150908
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit
repair, component replacement or complete product replacement in the event of malfunction. The decision to repair or
replace will be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and
excludes normal wear and tear or cosmetic damage.
Visit the product page located at wyrestorm.com for additional information on this product including important
technical information not provided in this document and warranty terms & conditions.
Pin 1
Pin 8
RJ-45 Connector (Gold Pins Facing Up)
Pin 2:
Orange
GreenPin 6:
Pin 1: White/Orange
Pin 5: White/Blue
Pin 3: White/Green Pin 7: White/Brown
Pin 4: Blue
Pin 8: Brown
2 of 2
  • Page 1 1
  • Page 2 2

Wyrestorm TX-SW-0201 Quick start guide

Wyrestorm
Brand
Wyrestorm
Model
TX-SW-0201
Category
Video splitters
Type
Quick start guide

Wyrestorm TX-SW-0201 is an auto-switching HDBaseT transmitter designed to send VGA or HDMI signals to a device with integrated HDBaseT receiving capability, such as a display or projector, over distances of up to 100m/328ft (4K - 70m/230ft). Perfect for small meeting room or classroom environments, the TX-SW-0201 supports video resolutions up to 4096 x 2160 @ 30Hz (4K) for HDMI and up to 1920 x 1200 for VGA. It also supports 3D Blu-ray and satellite/cable interlaced stereoscopic formats. With its 12V DC 1A power supply, the TX-SW-0201 consumes a maximum of 35W of power.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers