Webasto 21330-025 Installation guide

Webasto
Brand
Webasto
Model
21330-025
Category
Wall & ceiling mounts accessories
Type
Installation guide

Webasto 21330-025 is a cost-efficient, space-saving processor controlled battery charger, which means that you can charge and maintain your battery without any hassle. The Webasto 21330-025 is ideal for charging batteries ranging from 100 to 140Ah and is perfect for use with motorbikes, classic cars and boats. Not only does it have a rugged aluminum casing, it also features a spark-free and polarity-proof connection. It is equipped with a 7-step fully automatic charging process, which will charge your battery up to 100% and extend its service life significantly.

Webasto 21330-025 is a cost-efficient, space-saving processor controlled battery charger, which means that you can charge and maintain your battery without any hassle. The Webasto 21330-025 is ideal for charging batteries ranging from 100 to 140Ah and is perfect for use with motorbikes, classic cars and boats. Not only does it have a rugged aluminum casing, it also features a spark-free and polarity-proof connection. It is equipped with a 7-step fully automatic charging process, which will charge your battery up to 100% and extend its service life significantly.

IT IS RECOMMEND THAT A LICENSED ELECTRICIAN INSTALL
THE ELECTRICAL SERVICE AND THE CHARGING STATION.
Model Plug-in EVSE-RS not for outdoor installation
NOTICE TO ELECTRICIAN: Leave this Installation Guide with the EVSE-RS Plug-in customer for future reference.
AeroVironment EV Solutions™ EVSE-RS Plug-in Charging Station
INSTALLATION GUIDE
21
3 4
(A)
45 in.
(114.3 cm)
to oor
45 in.
to oor
wall stud
Pin Installation Template to the “center point mark” (Point A).
CHARGER
MOUNTING
DRILL .234 DIA X 2.00 DEEP
INTO CENTERLINE OF STUD
APPROXIMATELY 17 INCHES
A
Detail of template
INSTALLATION STEPS
Measure and mark a point on the wall stud 45 inches
from the oor.
Use Stud Finder to locate wall stud.
Mark the center point of the wall stud.
Use Level to straighten Installation Template.
Tape Template in place.
Install a 6-50 receptacle according to the allowable locations
and orientation indicated on the Installation Template.
5
6
7 8
CHARGER
MOUNTING
STUD CENTERLINE
45 INCHES TO FLOOR
3.345 INCHES
A
Using Socket Wrench, tighten Mounting Plate lag bolts
and washers.
Using Phillips Screwdriver, tighten screws for Cable Hanger.
Postiion the station with the mounting bosses inserted into
the corresponding openings in the plate.
Slide Charging Station down onto Mounting Plate to latch
into place.
Turn off power to the Receptacle.
Plug the Charging Station into the Receptacle. Ensure that
Plug is fully inserted into the Receptacle.
Turn on power to the Receptacle.
Drill holes for
Cable Hanger using
1
/
8
inch drill bit in 2
places
Drill holes in Cable
Hanger using
7
/
32
inch
drill bit in 2 places.
Drill holes for Mounting
Plate using a
1
/
4
inch
drill bit. in 2 places on
centerline of stud
HARDWARE KIT CONTENTS
1 - Mounting Plate
2 -
3
/
8
inch x 2½ inch Lag Bolts
2 -
3
/
8
inch Flat Washers
2 - #8 x 2½ inch Painted Head Wood Screws
PACKAGING CONTENTS
HARDWARE KIT
QUICK START GUIDE
CHARGING STATION
CABLE HANGER
INSTALLATION TEMPLATE
TOOLS (not included)
1. Electronic Stud Finder
2. Drill
3.
1
/
8
inch Drill Bit
4.
7
/
32
inch Drill Bit
5.
1
/
4
inch Drill Bit
6. Carpenter’s Level
7.
9
/
16
inch Socket Wrench
8. #2 Phillips Screwdriver
9. Measuring Tape
10. Masking Tape
11. Push pin / Tack
Customer Support:
1-888-833-2148
1
2
3
1
/
8
in.
4
7
/
32
in.
5
1
/
4
in.
6
7
8
9
10
11
21325-76 Rev.1
CORPORATE HEADQUARTERS
AeroVironment, Inc.
ev@avinc.com ● www.avinc.com/evsolutions
© 2012 AeroVironment, Inc. All rights reserved.
AeroVironment, EVSE-RS Plug-in, EV Solutions, and the AeroVironment logo are trademarks of AeroVironment, Inc.
Corporate names, trademarks, registered trademarks, service marks, symbols, and logos stated herein are property of their
respective companies.
Specications are subject to change without notice. Images of the Charging Station Model EVSE-RS Plug-in are representative;
production models may vary.
No portion of these materials may be duplicated, used or disclosed without prior written permission from AeroVironment, Inc.
Disclaimer: This Installation Guide includes the latest information available at the time of printing. AeroVironment, Inc.
reserves the right to make changes to this user guide and/or product without further notice. Changes or modications to this
product not completed by an authorized service provider could void the product warranty.
INSTALLATION GUIDE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Webasto 21330-025 Installation guide

Webasto
Brand
Webasto
Model
21330-025
Category
Wall & ceiling mounts accessories
Type
Installation guide

Webasto 21330-025 is a cost-efficient, space-saving processor controlled battery charger, which means that you can charge and maintain your battery without any hassle. The Webasto 21330-025 is ideal for charging batteries ranging from 100 to 140Ah and is perfect for use with motorbikes, classic cars and boats. Not only does it have a rugged aluminum casing, it also features a spark-free and polarity-proof connection. It is equipped with a 7-step fully automatic charging process, which will charge your battery up to 100% and extend its service life significantly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents