Dynabrade Dynafile II 40501 Operating And Safety Instructions Manual

Brand: Dynabrade

Model: Dynafile II 40501

Category: Power tools

Type: Operating And Safety Instructions Manual

This manual is also suitable for

Dynabrade Dynafile II 40501 is an electric abrasive belt machine designed for various sanding and grinding applications. It features a powerful 120V/60Hz motor for efficient operation. The tool has a compact and ergonomic design, allowing for comfortable handling and precise control.

With its adjustable housing angle, the Dynafile II 40501 enables users to customize the working angle for optimal comfort and efficiency. The side handle provides additional support and stability, especially during extended use.

The tool utilizes abrasive belts and contact arms, which can be easily changed to accommodate different materials and applications. The rough adjustment knob allows for precise belt tracking, ensuring optimal performance and extending the lifespan of the abrasive belt.

Parts Page Reorder No. PD01•94

Effective November, 2001

Supersedes PD96•09

Models:

40500 – 120 V / 60 Hz

40501 – Kit 120 V / 60 Hz

Abrasive Belt Machine

Electric Dynafile

Always operate, inspect and maintain this tool in accordance with the safety standards established by OSHA,

Underwriters Laboratories, Inc., The Canadian Standards Association and The American National Standards

Institute (ANSI). Dynabrade, Inc. assumes no responsibility for any damage or accidents resulting from the

misuse of this tool, its misapplication or non-adherence to precautionary safety measures.

WARNING

General Safety Rules

Read and save all instructions before operating this power tool.

Warning:

When using electric tools, basic safety precautions should always be followed to

reduce the risk of a fire, electric shock, and personal injury, including the following:

1. Keep work area clean. Cluttered areas and benches invite accidents.

2. Consider work area environment. Do not expose tools to rain. Keep

work area well lit. Do not use power tools in damp or wet locations.

Do not use tools in the presence of flammable liquids or gases.

3. Guard against electric shock. Prevent body contact with grounded

surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

4. Keep children away. Do not let visitors contact tool or extension cord.

All visitors should be kept away from work area.

5. Store idle tools. When not in use, tools should be stored in a dry, or locked

place - out of the reach of children.

6. Do not force tool. It will do a better and safer job at its intended rate.

7. Use the right tool. Do not force a small tool or attachment to do the job of

a heavy duty tool. Do not use tool for purposes not intended.

8. Dress properly. Do not wear loose fitting clothing or jewelry. Clothes can

be caught in moving parts. Rubber gloves and non-skid footwear are

recommended when working outdoors. Wear protective hair covering to

contain long hair.

9. Use safety glasses. Also use face-shield or dust mask if operation area is dusty.

10. Do not abuse cord. Never carry tool by cord or yank it to disconnect from

receptacle. Keep cord from heat, oil and sharp edges.

11. Secure work. Use clamps or a vice to hold workpiece. It’s safer than

using your hand and it frees up both hands to operate tool.

12. Do not overreach. Keep proper footing and balance at all times.

13. Maintain tools with care. Keep tools clean for better use and safer

performance. Follow instructions for lubricating and changing accessories.

Inspect tool cords periodically and if damaged, have repaired by authorized

service facility. Inspect extension cords periodically and replace if damaged.

Keep handles dry, clean and free from oil and grease.

14. Do not leave tool running. Disconnect tools when not in use, before

servicing, when changing belts, contact arms, etc.

15. Remove keys and wrenches. Form a habit of checking to see that all

keys and adjusting wrenches are removed from tool before turning it on.

16. Avoid accidental starting. Do not carry around plugged in tool with finger

on lever. Be sure lever is off when plugging in.

17. Out-door use extension cords. When tool is used outdoors, use only

extension cord suitable for outdoor use. They should be marked with the

suffix W-A (for UL) or W (for CSA in Canada).

18. Stay alert. Watch what you are doing. Use common sense.

Do not operate tool when you are tired.

19. Check damaged parts. Before further use of the tool, a guard or other

part that is damaged should be carefully checked to determine that it will

operate properly and perform its intended function. Check for alignment of

moving parts, breakage of moving parts, binding of moving parts, mounting

and any other conditions that may affect its operation. A guard or other

part that is damaged should be properly repaired or replaced by an

authorized service center unless otherwise indicated elsewhere in this

instruction manual. Have defective switches replaced. Do not use tool if

switch does not turn tool on or off.

20. Avoid gaseous areas. Do not operate portable electric tools in

gaseous or explosive atmospheres. Motors in these tools

normally spark, and the sparks can ignite fumes.

21. Do not alter or misuse tool. This tool is precision built. Any

alteration or modification not specified is misuse and may result in a

dangerous condition. Only these accessories and attachments that

are found in this instruction manual are acceptable for use with this

tool. The use of any other accessory or attachment might present a risk

to the operator.

22. Replacement parts. When servicing, use only identical replacement

parts. When ordering replacement parts, please specify model and

serial numbers of your machine.

Voltage Warning

Before connecting the tool to a power source (receptacle, outlet,

etc.), be sure the voltage supplied is the same as what is specified

on the nameplate of the tool. A power source with greater than that

specified for tool can result in serious injury to the user as well as

damage to the tool. Using a power source with voltage less than the

nameplate rating is harmful to the tool’s motor. If in doubt, do not

plug in the tool.

Double Insulation

Your Electric Dynafile

II is double-insulated to give you added

safety. This means that the tool is constructed throughout with two

separate “layers” of electrical insulation, or one double thickness of

insulation between you and the tool’s electrical system.

Tools built with this type of insulation system are not intended to be

grounded. As a result, your Electric Dynafile

II is equipped with a two

prong plug which permits you to use extension cords without concern

for maintaining a ground connection.

Note: Double-insulation does not take the place of normal safety

precautions when operating this tool. The insulation system is

added for protection against injury resulting from a possible

electrical insulation failure within the tool.

Caution: When servicing double-insulated tools, use only identical

replacement parts. Repair or replace damaged cords.

Extension Cords

Double-insulated tools have two-wire cords, and can be used with

either two-wire or three-wire extension cords. Only round jacketed

extension cords should be used, and we recommend that they be

listed by Underwriters Laboratories (UL) - (CSA in Canada). If the

extension cords will be used outside, the cord must be suitable for

outdoor use. They should be marked with the suffix W-A (for UL) or

W (for CSA in Canada). Any cord marked as an outdoor cord can

also be used for indoor work.

Polarized Plugs: To reduce the risk of electric shock, this equipment has

a polarized plug (one blade is wider than the other). This plug will fit

in a polarized outlet only one way. If the plug does not fit in the outlet,

reverse the plug. If it still does not fit, contact a qualified electrician to

install the proper outlet. Do not change the plug in any way.

Warning: Keep extension away from the immediate working area.

For Serial No. 0A1000 and Higher

Important Operating and Safety Instructions

Carefully read all instructions before operating or servicing any Dynabrade

Abrasive Power Tool.

Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.

Operating Instructions:

Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious

injury or death. Follow safety procedures posted in workplace.

1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.

2. Connect power source to tool. Be careful not to depress paddle switch in the process.

3. Hold tool by the motor housing only. One or two hands may be used. Do Not hold tool by head/housing assembly. Keep hands away from

all grinding/sanding edges and moving parts. A side handle is included for two hand operation of tool. (See “Installing Side Handle” instructions.)

4. Depress paddle switch (trigger) and hold to start tool. Release switch to stop tool.

5. While tool is running, Adjust belt tracking by tuning 95218 Rough Adjustment Knob to the left or right accordingly, so as abrasive belt

rides evenly over contact arm.

6. Always work off the return-side of the abrasive belt. This will ensure superior tracking and reduce downtime of tool.

Housing Angle Adjustment:

To pivot housing, loosen 95311 Screw on housing with the supplied 9/64" hex wrench (P/N – 95134). Pivot housing to desired angle and

retighten 95311 Screw.

Installing Side Handle:

The side handle may be installed on either side of the rotor housing for right or left hand operation. Position the side handle on the side offering

the best comfort and control of the tool. To install, thread side handle into side handle socket on desired side of motor housing and tighten securely.

Full One Year Warranty

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one

year from the date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal

use and service. We shall repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the

original purchaser, indicate upon our examination to have been defective.

Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety prac-

tices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its nor-

mal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.

To Change Belt:

1. Disconnect power source.

2. Remove 40365 Belt Guard by pulling backwards and

upwards over the 40314 Button Latch Assembly.

3 Pull back on tension arm assembly.

4. Remove and replace abrasive belt and belt guard.

5. Connect power source.

6. Adjust belt tracking by turning 95218 Rough Adjustment Knob

to the left or right accordingly while machine is running.

To Change Contact Arm Assembly:

1. Disconnect power source.

2. Remove 40365 Belt Guard by pulling backwards and

upwards over the 40314 Button Latch Assembly.

3. Pull back on tension arm assembly and remove abrasive belt.

4. Remove 95218 Rough Adjustment Knob.

5. Remove contact arm and replace with desired arm, making sure

that the tab on the end of the arm is facing downward.

6. Replace 95218 Knob.

7. Install abrasive belt and replace belt guard.

8. Connect power source and adjust belt tracking by turning

95218 Knob.

Abrasive Belt/Contact Arm Change Instructions

Safety Instructions:

Products offered by Dynabrade should not be converted or otherwise altered

from original design without expressed written consent from Dynabrade, Inc.

Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious

injury or death. Follow safety procedures posted in workplace.

Important: User of tool is responsible for following accepted safety codes such as those published by the American National

Standards Institute (ANSI).

• Operate machine for 30 seconds before application to workpiece to determine if machine is working properly and safely before work begins.

• Always disconnect power supply before changing abrasive or making machine adjustments.

• Inspect abrasives and accessories for damage or defects prior to installation on tools.

• Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.

Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.

Extension Cords

Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the sup-

ply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage

resulting in loss of power and possible tool damage. Refer to the table below to determine the required minimum wire size.

The smaller the gauge number of the wire the greater the capacity of the cord. For example a 14 gauge cord can carry a higher current than a 16 gauge

cord. When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required. If you are

using one extension cord for more than one tool, add the nameplate ampere and use the sum to determine the required minimum wire size.

Guidelines For Using Extension Cords

• If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use.

• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified

person before using it.

• Protect your extension cords sharp objects, excessive heat and damp or wet areas.

Read and save all instructions for future reference

Head/Housing Assembly

Electric Motor only (See page 4 for Electric Motor Parts Breakdown)

Note: Shaded parts represent 15372 Housing Assembly.

Nameplate Extension Cord Length

Ampere 25' 50' 75' 100' 150' 200'

0–5.0 16 16 16 14 12 12

5.1–8.0 16 16 14 12 10 –

8.1–12.0 14 14 12 10 – –

12.1–15.0 12 12 10 10 – –

15.1–20.0 10 10 10 – – –

*Based on limiting the line

voltage drop to live volts at

150% of the rated ampere.

1 Contact Arm Assembly

(See Chart on pg.6)

2 96334 Plug

3 15308 Guide Post

4 11040 Spring

5 15306 Tension Arm

6 95426 Spring

7 95218 Knob Assembly

8 15309 Dust Cover

9 15307 Tension Shaft

10 15329 Screw

11 15312 Belt Guard

12 96335 Hex Nut

13 15366 Housing

14 95311 Screw

15 40029 Motor Lock

16 95217 Screw

17 40511 Drive Wheel

18 40513 Adapter

19 96110 Set Screw

20 40520 Electric Motor

21 95042 Washer

22 11535 Side Handle

Index Key

No. Part # Description

40520 Motor Assembly

To order replacement parts, specify model number and serial number of your machine.

1 40567 Cord Protector

2 40522 Cord Set

3 40523 Service Nameplate Kit

4 40524 Trigger

5 40525 .146 Dia. x 1-3/8" Rivet

6 40526 Motor Housing

7 40527 O-Ring

8 40528 Left Brush Holder

9 40529 Switch

10 40532 Cover

11 40548 8-16 x 5/8" Pan Hd.

Slt.Plast. T-20

12 40534 Brush

13 40535 Right Brush Holder

14 40536 Brush Spring

15 40537 Rubber Bumper

16 40538 Rear Bearing

17 40539 120 Volt Field

18 40540 8-16 x 2-1/2" Pan Hd.

Slt. Plast T-20

19 40541 120 Volt Armature

(Includes 40542 Fan)

20 40542 Fan

21 40543 8-32 x 3/8" Pan Hd.

Slt. Plast. T-20

22 40544 Front Bearing

23 40545 Pinion

24 40546 1/4-28 Hex Lock Nut

25 40548 8-16 x 5/8" Pan Hd.

Slt.Plast T-20

26 40549 Gear Case Assembly

(Incl. All Shaded Index #'s)

27 40550 Needle Bearing

28 40551 Coil Spring

29 40553 Spiral Bevel Gear

30 40554 Internal Retaining Ring

31 40555 Bearing

32 40557 Spindle Hub

33 40558 8-32 x 1/2" Pan Hd.

Slt. Taptitet T-20

34 40559 Spindle

35 40561 Shim

36 40562 Cap

37 40564 Coil Spring

38 40565 O-Ring

39 40566 Lock Pin

Index Key

No. Part # Description

37 26

14 13

124

Dynafile

II Contact Arms

Optional 40078 Adapter allows use

of 24" long belts; extends reach to

7" when used with contact arm.

Arms for 4" to 17" workable reach.

45 PSI maximum.

Enter channels as

small as 7/16".

Belt Size: 1/2" W x 18" L.

Contact Wheel: 5/16" dia. x 3/8" W, rubber.

Platen: 1/2" wide.

Work on broad areas, leaves

in-line scratch, blend stainless.

11200

11024 steel platen available.

6-3/4" workable reach.

11286

Belt Size: 1/2" W x 24" L.

Contact Wheel: 5/8" dia. x 3/8" W, rubber. Platen: 1/2" wide.

Grind on contact wheel

or platen; has 5-1/4"

workable reach.

11201

Belt Size: 1/2" W x 18" L.

Contact Wheel: 5/16" dia. x 3/8" W, steel.

Platen: 1/2" wide.

11202

Enter 5/16" x 3/4" openings.

Belt Size: 1/4" W x 18" L.

Contact Wheel: 5/8" dia. x 1/8" W, rubber.

Platen: 1/4" wide.

11287 Uses 20-1/2" Belts

Belt Size: 5/8" or 3/4" W x 20-1/2" L

Contact Wheel: 3/4" dia. x 5/8" W, rubber. Platen: 3/4" wide.

11304 “The Banana Arm”

Work on broad areas;

leaves in-line scratch;

blend stainless.

Belt Size: 1/2" W x 18" L.

Contact Wheel: 5/8" dia. x 3/8" wide, rubber. Platen: 1/2" wide.

2-1/2"

Rubber

11322 Guide-Cut

Removes raised material within

.020" or less without undercutting.

Guide Wheels

Prevent Undercutting

Belt Size: 1/2" W x 18" L. 60 to 80 grit.

Contact Wheel: 5/8" dia. x 3/8" W, rubber.

11329 Extra Length Arm

17" workable reach.

Belt Size: 1/2" W x 44" L.

Contact Wheel: 5/8" dia. x 3/8" W, rubber. Platen: 1/2" wide.

11350 “Bus Bar”

Excellent for cleaning oxide

off electrical bus bars. Arm

has a 12" workable reach.

Belt Size: 3/4" W x 34" L.

Contact Wheel: 5/16" dia. x 5/8" W, steel. Platen: 3/4" wide, optional.

11220, 11300, 11301, 11341

Polish Turbine Blades

Offset design and miniature

contact wheels. 2" strap polish

in offset area; polish turbine

blades and other contours.

11203* Order 11312 for heavy-duty version.

Grind over contact

wheel or platen.

Belt Size: 1/2" W x 18" L.

Contact Wheel: 5/8" dia. x 3/8" W, rubber. Platen: 1/2" wide.

11204 – “Unique Offset Design”

Strap polish is easy with this arm!

Belt Size: 1/4" or 1/2" W x 18" L.

Contact Wheel: 1" dia. x 3/8" W, rubber. Platen: None due to offset design.

11206

Belt Size: 5/8" or 3/4" W x 18" L.

Contact Wheel: 3/4" dia. x 5/8" wide, rubber. Platen: 3/4" wide.

taperedStrap polish here

Order 11326 for Heavy Duty/Steel Construction version.

11280

Belt Sizes: 11220 uses 5/8" or 3/4" W x 18" L.

All others use 1/2" W x 18" L.

Contact wheels description for each above arm:

11220: 5/16" dia. x 5/8" W, steel. 11300: 1/4" dia. x 3/8" W, steel.

11301: 5/16" dia. x 3/8" W, steel. 11341: 5/16" dia. x 3/8" W, rubber.

Belt Size: 1/4" W x 18" L.

Contact Wheel: 1" dia. x 3/8" wide, urethane, tapered.

Platen: No platen due to offset design.

*Standard Contact Arm for Electric Dynafile

Grind corners, enter

grooves, strap polish.

Dynafile

II Standard Contact Arms

Part Abrasive Contact Wheel Contact Wheel Contact Wheel Bearing

Number Belt Size Description Comments Assembly Only (2) Req. Shaft

11200 1/2" x 18" 5/8" Dia. x 3/8" W Rubber “Stroke-Sander Arm” 11088 (2) 11077 (2) 11052 (4) 11055 (2)

1/2" W Platen

11201 1/2" x 18" 5/16" Dia. x 3/8" W Steel 1/2" W Platen 11068 11067 11051 11054

11202 1/4" x 18" 5/8" Dia. x 1/8" W Rubber 1/4" W Platen 11074 11073 11052 11053

11203 1/2" x 18" 5/8" Dia. x 3/8" W Rubber 1/2" W Platen 11078 11077 11052 11054

11204 1/4" or 1/2" x 18" 1" Dia. x 3/8" Wide Loose Belt Application 11080 11079 11052 11054

Radiused Rubber

11206 5/8" or 3/4" x 18" 3/4" Dia. x 5/8" W Rubber 3/4" W Platen 11282 11281 11052 11285

11220 5/8" or 3/4" x 18" 5/16" Dia. x 5/8" W Steel Polish Turbine Blades 11352 11353 11051 11285

11280 1/4" x 18" 1" Dia. x 3/8" Wide No Platen/Offset Design 11086 11085 11052 11054

Tapered Urethane

11286 1/2" x 24" 5/8" Dia. x 3/8" W Rubber 1/2" W Platen 11078 11077 11052 11054

11287 5/8" or 3/4" x 20-1/2" 3/4" Dia. x 5/8" W Rubber 3/4" W Platen 11282 11281 11052 11285

11300 1/2" x 18" 1/4" Dia. x 3/8" W Steel Polish Turbine Blades 11332 11333 11334 11335

11301 1/2" x 18" 5/16" Dia. x 3/8" W Steel Polish Turbine Blades 11068 11067 11051 11054

11304 1/2" x 18" 5/8" Dia. x 3/8" W Rubber “Stroke-Sander Arm”-1/2" W Platen 11078 11077 11052 11054

11312 1/2" x 18" 5/8" Dia. x 3/8" W Rubber H.D. Version of 11203 Arm 11078 11077 11052 11054

11320 1/2" x 18" 5/8" Dia. x 3/8" W Rubber “Offset Arm” – prevent gouging. 11078 11077 11052 11054

11322 1/2" x 18" 5/8" Dia. x 3/8" W Rubber Contains two 11395 Guide 11090 11077 11052 95610

Wheels – Prevents Undercutting

11325 1/2" x 18" 5/8" Dia. x 3/8" W Rubber 1/2" W Steel Platen 11078 11077 11052 11054

11326 5/8" or 3/4" x 18" 3/4" Dia. x 5/8" W Rubber H.D. Version of 11206 Arm 11282 11281 11052 11285

11329 1/2" x 44" 5/8" Dia. x 3/8" W Rubber 1/2" W Platen/17" Reach 11078 11077 11052 11054

11341 1/2" x 18" 5/16" Dia. x 3/8" W Rubber Polish Turbine Blades 11342 11343 11334 11335

11350 3/4" x 34" 5/16" Dia. x 5/8" W Steel Bus Bar Arm/11" Reach 11352 11353 11051 11285

Dynafile

II Contact Arm Assembly Parts List

Contact Wheel Assembly – Includes wheel, bearings and shaft.

Contact Arm

Shaft

Bearing

Contact Wheel

Bearing

Grade

Super Fine Very Fine Medium Coarse

1/4" 90158 90228 90229 –

1/2" 90159 90248 90292 90297

5/8" 90160 90249 90293 90298

3/4" 90161 90258 90294 90299

1" 90162 90259 90295 90300

3/4" 90620 90621 90622 90623

1/4" 90397 90403 90433 90460

1/2" 90398 90400 90434 90461

1" 90399 90402 90416 90462

Abrasive Belts

1/8" – 90211 90212 90143 90213 90214 90215 90216 90217

1/4" 90220 90221 90222 90144 90223 90224 90225 90226 90227

1/2" 90240 90241 90242 90145 90243 90244 90245 90246 90247

5/8" 90260 90261 90262 90146 90263 90264 90265 90266 90267

3/4" 90250 90251 90252 90147 90253 90254 90255 90256 90257

1" 90284 90285 90286 90148 90287 90288 90289 90290 90291

1/8" – 90405 90407 90408 90409 90410 90411 90412 90413

1/4" 90415 90417 90419 90420 90421 90423 90424 90425 90426

1/2" 90441 90443 90445 90446 90447 90449 90451 90453 90455

1" 90478 90482 90483 90491 90484 90486 90487 90488 90489

24" Long

18" Long

Abrasive Grit

40 60 80 100 120 180 220 320 500

Belt

Width

Coated Aluminum Oxide

Abrasive Grit

40 60 80 120

1/4" 91057 91058 91059 91048

1/2" 91066 91067 91068 91049

5/8" 91075 91076 91077 91050

3/4" 91084 91085 91086 91051

1" 91093 91094 91095 91052

1/4" 91111 91112 91113 91034

1/2" 91120 91121 91122 91035

18" Long

Belt

Width

24" Long

Ceramic Coated Aluminum Oxide

2" and Wider: 50 Belts = Unit.

All Other Belts: 200 Belts = Unit.

Abrasive Grit

60 80 120

1/8" 94827 94828 94829

1/4" 94838 94839 94840

1/2" 94847 94848 94849

5/8" 94856 94857 94858

3/4" 94866 94867 94868

1" 94877 94878 94879

1/8" 90463 90464 90562

1/4" 90563 90564 90565

1/2" 90567 90568 90569

1" 90480 90481 90544

18" Long

24" Long

Belt

Width

200 Belts = Unit.

Coated Silicon Carbide

Abrasive Grit

60 80

1/4" 90166 90167

1/2" 90168 90169

5/8" 90170 90171

3/4" 90172 90173

1" 90177 90178

1/4" 90577 90582

1/2" 90579 90583

1" 90485 90474

24" Long

18" Long

Belt

Width

2" and Wider: 50 Belts = Unit.

All Other Belts: 200 Belts = Unit.

Coated Alumina Zirconia

Part Number Use With

1/2" 90010 Dynafile

II Adapter

24" Long

Belt

Width

Cloth Polishing Belts

Belt

Width

18" Long

1" and Wider: 10 Belts = Unit. All Other Belts: 20 Belts = Unit.

Abrasive Impregnated Non-Woven Nylon

20-1/2" Long

24" Long

Abrasive Impregnated Non-Woven Nylon

A non-woven synthetic fiber and an abrasive mineral are bonded together to

form a tough, open web that is chemically resistant and long-lasting. This

web design allows controlled conformable contact to workpiece contours,

corners and edges. The product wears away slowly, exposing new abra-

sive leaving a uniform, consistent surface. It also conditions surfaces with-

out removing or damaging the base material and is excellent for deburring,

cleaning, blending and final finishing of metal, wood and plastics. It is avail-

able in many forms such as belts, discs and wheels. Various mineral

grades are available ranging from very coarse to ultra-fine.

Cloth Polishing Belts

Used on power tools in conjunction with Dynuba

polishing compounds.

The result is brilliant cut, color and luster on metals such as stainless steel,

aluminum, copper and brass.

Coated Aluminum Oxide

The most widely used abrasive grain. This tough durable synthetic is used for

grinding and deburring high carbon steels, general metalworking and for

sanding certain hardwoods.

Ceramic Coated Aluminum Oxide

Synthetic grain two-to-three times tougher than conventional aluminum oxide.

Coated Silicon Carbide

Excellent for sanding primer and sealer. This sharp, fast-penetrating grain is

used for sanding soft materials such as glass, plastics and fibrous wood.

Coated Alumina Zirconia

Effective for coarse stock removal of metal and wood. This synthetic grain

has self-sharpening characteristics and provides continuous new cutting

edges for longer life and greater efficiency.

Abrasive Types and Cloth Polishing Belts

Dynapad

Platen Pads

Note: Dynapad Platen Pads are PSA mounted and easily trimmed to size.

Exceptions: 11024 and 11028 Steel Platens bolt on; 14341 clamps on. Unit = 10 packages each.

Part Pkg.

Number Used On Size Material Qty.

11024 Dynafile II (11286 Arm) 1/2" W x 3" L (bolts on) Steel 1

11025 Dynafile, Dynafile II 1/2" W x 7" L x 1/8" Thk Soft/Sponge 5

11026 Dynafile, Dynafile II 1/2" W x 7" L x 1/8" Thk Hard/ Cork 5

11027 Dynafile, Dynafile II 1/2" W x 7" L x 1/32" Thk Thin 5

11028 Dynafile (11228 Arm) 1/2" W x 3" L (bolts on) Steel 1

11032 Dynafile 1/4" W x 7" L x 1/8" Thk Soft/ Sponge 5

11033 Dynafile 1/4" W x 7" L x 1/8" Thk Hard/ Cork 5

11034 Dynafile 1/4" W x 7" L x 1/32" Thk Thin 5

11109 Dynafile II 3/4" W x 7" L x 1/8" Thk Hard/ Cork 5

11119 Dynafile II 3/4" W x 7" L x 1/8" Thk Soft/ Sponge 5

11129 Dynafile II 3/4" W x 7" L x 1/32" Thk Thin 5

DYNABRADE

DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524

DYNABRADE EUROPE S.àr.l., Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1

Visit Our Web Site: www.dynabrade.com Email: Customer[email protected]

Model Motor Sound Abrasive Belt Size Max. SFPM Weight Length Height

Number RPM Level Inch (mm) Voltage Current Phase Frequency (SMPM) Pound (kg) Inch (mm) Inch (mm)

40500 10,000 86 dB(A) 1/4-3/4 (6-19) W x 18-24 (457-610) L 120 V (AC) 5.5 Amps 1 60 Hz 2,300 (699) 5.5 (2.5) 15.0 (381) 4.0 (102)

Machine Specifications

Dynabrade Dynafile II 40501 Operating And Safety Instructions Manual

Brand: Dynabrade

Model: Dynafile II 40501

Category: Power tools

Type: Operating And Safety Instructions Manual

This manual is also suitable for

Download PDF

report

Dynabrade Dynafile II 40501 Operating And Safety Instructions Manual

This manual is also suitable for

Dynabrade Dynafile II 40501 Operating And Safety Instructions Manual

Related papers

Other documents