Installation and Operation Guide
High-Flow Pro Series Systems
Welcome to the Aquasana experience. You are about to provide your patrons
with clean, healthy water and the peace of mind that comes from knowing award
winning filter technology is working for you.
Installation must comply with state and local laws.
Items that may be needed for installation
• Variable speed drill
• Adjustable wrench
• Drill bits
• Measuring tape
• Wall anchors
• Bucket
• Teflon® tape
• Pipe dope
• Copper tubing
• Propane torch
• Solder
• Level
32.38”
26.38” 20.25”
22.25”
22.25”
22.25”
15.5”
14”
8”
8”
Standard Kits:
9.75 lbs.
10 lbs
15 lbs
25 lbs
30 lbs
20 lbs
Warnings
• Please read and understand entire manual before attempting to assemble, operate and install product.
• Risk of leaks, which could lead to flooding, if not installed according to the installation instructions.
• It is recommended that this system be installed by an approved or certified professional.
Do not use with water that is microbiologically unsafe or of unknown water quality without adequate
disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected
waters that may contain filterable cysts.
Long-lasting, high performance water filtration for
great-tasting, healthy water throughout your entire
establishment.
Installation
1. Shut o water supply and select a mounting location
a) The location should allow for a minimum clearance of 2 ½ inches under the cartridge(s)
so they can be removed and replaced.
b) Provide adequate space on both sides for plumbing and also for system flushing.
2. Install gauges provided onto manifolds as shown
*Use Teflon
®
tape
3. Install “T” fitting and drain shut-o valve onto outlet port ¾” NPT *Use Teflon
®
tape
4. Install manifold bracket onto wall
a) Use level and predrilled mounting holes in
the manifold bracket as guides.
b) Mark and drill anchor holes.
c) Ensure that bracket is mounted level and securely.
Note:
Entry gauge goes
on front pipe.
Exit gauge goes
on back pipe.
CAUTION!
DO NOT
OVER-TIGHTEN
gauges or
connections
5. Plumb to connect ¾” NPT connections
a) Connect inlet + outlet ports of High-Flow Systems to water consuming equipment being fed.
b) Use an industry approved pipe dope or Teflon
®
tape at all connections.
c) Always use a wrench on all the fittings to avoid undue stress on system components.
d) Careful when sweating joints not to damage elastomeric components.
6. Plumb to connect to beverage center if applicable
a) Plumb to exit port of “H” Adapter if feeding
water to a carbonated beverage products.
b) Special line must run from exit port shown
directly to beverage center.
7. Install twist and lock cartridges as shown
Each cartridge will “click” into place when fully engaged after quarter turn.
8. System check and flush
a) Check all connections and proceed to turn on water supply.
b) Once system is pressurized, check for leaks.
c) Open flushing valve and flush the cartridge(s) by running water through at full force for
approx. 5 minutes. This will purge the system free of air and flush any fines, ensuring
maximum filter life and high performing water at startup.
d) After flushing, the system is ready for operation and usage.
Exit port
⁄” FNPT
Filter Change Instructions
1. Typically every 6 months but is dependent upon usage and overall quality of supply water.
2. When pressure on exit gauge drops below 10 psi this could be a sign that the filters are
starting to clog (which means that they are not working).
3. It is recommended that all cartridges in system be replaced at the same time.
Step 1 Step 2 Step 3 Step 4
Installation Guide
Aquasana Pro Series systems are designed to be customized to fit your specific water
usage requirements. Below is a general guide to the installation order for filtration
cartridges. Based on your specific usage requirements, your system may not include
all cartridges shown. If you have any questions about the installation order of your
cartridges, please contact us at 855.245.1884 or [email protected].
Cartridge Order
Sediment cartridge
always comes first
Chloramines cartridge(s)
always go after sediment
Scale cartridge
always goes last
Filter Change Instructions
1. Typically every 6 months but is dependent upon usage and overall quality of supply water.
2. When pressure on exit gauge drops below 10 psi this could be a sign that the filters are
starting to clog (which means that they are not working).
3. It is recommended that all cartridges in system be replaced at the same time.
Troubleshooting Guide
Symptom Cause Action
Flow/Pressure
Too Low Incoming water valve not completely open Open incoming water valve to full open
Too Low Clogged filter cartridge Replace filter cartridges
Too Low Defective pressure gauge Remove and replace pressure gauge
using Teflon
®
tape
Leaking
Cartridge Defective or damaged cartridge O-ring Remove and replace cartridge O-rings
or replace filter cartridge
Manifold Defective or damaged manifold O-ring Disassemble manifold and remove and
replace manifold O-rings
Defective of broken retaining clip (red) Remove and replace clip
Defective or damaged manifold rotator Disassemble manifold from bracket and
replace with a new manifold
Gauge Gauge not installed properly Remove gauge, apply Teflon
®
tape and
reinstall
Defective or damaged gauge Remove and replace pressure gauge
(use Teflon
®
tape)
Taste of water or beverages
Bitter tasting
water
System not flushed properly Flush system utilizing flush drain at exit
port of system manifold
Low carbonation System not installed/plumbed properly Correct plumbing so that carbonated
beverage center receives
Filter system growing scale
Scale reduction cartridge has reached
capacity
Remove and replace scale reduction
cartridge
Pure Satisfaction
All Aquasana products oer a 90-day 100% money-back guarantee. (A one-year warranty is
included, which covers defects in materials and workmanship.) If for any reason you are not
satisfied with your purchase, simply call us or the dealer from whom you purchased for a
Return Authorization Code, and a full refund will be promptly issued upon return. Thank you
for choosing Aquasana!
This filter system is designed and tested for use with genuine Aquasana parts including
replacement filters and all hardware. Use of parts from other manufacturers may result in
loss of contaminant reduction performance, system damage or failure. Use of parts from
other manufacturers will also void your warranty. Please visit your distributor or contact us at
aquasana.com or 855.245.1884 for replacement parts.
Aquasana, Inc.
6310 Midway Road
Haltom City, Texas 76117
855.245.1884
www.aquasana.com
For exclusive deals
facebook.com/aquasana
twitter.com/aquasana
proSeries_generic_20140421
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Aquasana FS-SC-10-R Operating instructions
-
-
Aquasana AQ-5300.56 User manual
-
-
-
-
-
-
-