Milwaukee M12 HAMMERVAC 2306-20 User manual

Brand: Milwaukee

Model: M12 HAMMERVAC 2306-20

Category: Rotary hammers

Type: User manual

This manual is also suitable for

Cat. No.

No de Cat.

2306-20

M12™ HAMMERVAC™ UNIVERSAL DUST EXTRACTOR

M12™HAMMERVAC™DÉPOUSSIÉREUR UNIVERSEL

EXTRACTOR UNIVERSAL DE POLVO M12™ HAMMERVAC™

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

2 3

IMPORTANT SAFETY INSTRUCTIONS

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Dust extractors have motors and other parts

that can produce sparks during normal use.

Do not use within 30 feet of areas where explosive

materials may be present (such as gasoline pumps

and places where liquids like paint thinners, clean-

ers, solvents, etc. are stored).

• Do not use in the presence of explosive dust,

liquids or vapors.

• Do not use where oxygen or anesthetics are

used.

• Do not allow to be used as a toy. Close attention

is necessary when used by or near children.

• Use extra care when using on stairs.

• Do not pick up wet material. Do not use water

to settle dust.

• Do not handle battery pack or dust extractor

with wet hands.

• Do not pick up anything that is burning or

smoking such as cigarettes, matches, or hot

ashes.

• Do not pick up soot, cement, plaster or drywall

dust without ﬁ lter in place. These are very ﬁ ne

particles that may affect the performance of the

motor or be exhausted back into the air.

• To reduce the risk of health hazards from va-

pors or dust, do not vacuum toxic, carcinogenic

or other hazardous materials such as asbestos,

arsenic, barium, beryllium, lead, pesticides or other

health endangering materials.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

• Use special care when emptying heavily loaded

tanks.

• To avoid spontaneous combustion, empty dust

box after each use.

• Do not leave dust extractor unattended when

battery pack is installed. Remove battery pack

when not in use and before servicing.

• Do not put any object into openings. Do not use

with any opening blocked; keep free of dust, lint,

hair, and anything else that may reduce air ﬂ ow.

• Maintain dust extractor. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may affect

the dust extractor's operation. If damaged, have

the dust extractor repaired before use. Many

accidents are caused by poorly maintained tools.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• Use dust extractor only with speciﬁ cally des-

ignated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

PERSONAL SAFETY

WORK AREA SAFETY

ELECTRICAL SAFETY

WARNING WHEN USING AN ELECTRICAL DUST EXTRACTOR,

BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE

FOLLOWING: READ ALL INSTRUCTIONS BEFORE USING DUST EXTRAC-

TOR. FOR HOUSEHOLD OR COMMERCIAL USE. BEFORE USING THE DUST

EXTRACTOR, READ THIS OPERATOR’S MANUAL, YOUR TOOL, BATTERY

PACK AND CHARGER OPERATOR’S MANUALS, AND ALL LABELS ON THE

DUST EXTRACTOR, BATTERY PACK, CHARGER AND TOOL.

USE AND CARE

BATTERY PACK USE AND CARE

• STAY ALERT. Watch what you are doing and use

common sense. Do not use dust extractor when you

are tired, distracted or under the inﬂ uence of drugs,

alcohol or medication causing diminished control.

• The operation of a dust extractor can result in

foreign objects being blown into eyes, which can

result in eye damage. Always wear safety goggles

or glasses with side shields when operating dust

extractor.

• Wear a face or dust mask when working in dust

situations. Dust particles can harm your lungs.

• Avoid accidental starting. Ensure the switch is

in the off-position before inserting battery pack.

Inserting battery pack in dust extractor that has the

switch on invites accidents.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the dust extractor in unexpected situations.

• Keep hair, loose clothing, ﬁ ngers, and all parts

of body away from openings and moving parts.

• Use only as described in this manual. Use only

manufacturer’s recommended attachments.

• Do not use without dust box and/or ﬁ lter in

place.

• Do not use to pick up ﬂ ammable or combustible

liquids such as gasoline or use in areas where they

may be present.

READ AND SAVE ALL INSTRUCTIONS

FOR FUTURE USE

• Turn off all controls before removing battery pack.

• To reduce the risk of electric shock, do not use

on wet surfaces. Do not expose to rain. Store

indoors.

• Before using the battery pack or charger read

the operator’s manuals, and any labels on the

battery pack, charger and dust extractor.

• Recharge only with the charger speciﬁ ed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁ re

when used with another battery pack.

• When battery pack is not in use, keep it away

from other metal objects like paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal

to another. Shorting the battery terminals together

may cause burns or a ﬁ re.

• Do not use damaged battery pack or dust

extractor. If battery pack or dust extractor are not

working as they should, have been dropped, dam-

aged, left outdoors, or dropped into water, return

them to a service center.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

•Before using the dust extractor, read this op-

erator’s manual, your tool, battery pack and

charger operator’s manuals, and all labels

on the dust extractor, battery pack, charger

and tool.

• Always use side handle assembly with the

correct neck diameter for the rotary hammer/

hammer drill. An ill-ﬁ tting side handle will not

tighten securely, causing loss of control.

• Never use dust extractor without dust box and

HEPA ﬁ lter in place. Never use water to clean

dust box or HEPA ﬁ lter.

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Always use side handle provided with dust

extractor when using with a rotary hammer/

hammer drill. When dust extractor is removed

from the tool, always use side handle(s) sup-

plied with the tool. Loss of control can cause

personal injury.

• Hold power tool by insulated gripping sur-

faces, when performing an operation where the

fastener may contact hidden wiring. Fasteners

contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the

operator an electric shock.

FUNCTIONAL DESCRIPTION

1. Power Switch

2. Fuel Gauge

3. Dust Box Latch

4. Dust Box with Filter

5. Side Handle Clamp Attachment Point

6. Tool and Bit Adjustment Button

7. Depth Gauge

8. Depth Gauge Button

9. Nozzle

10. Nozzle Assembly

11. Bit Brush

12. Side Handle Clamping Collar Assembly

13. Clamp Lever

14. Side Handle Grip

4 5

ASSEMBLY

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body

of the tool. Make sure it latches securely into place.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

WARNING To reduce the risk of in-

jury, always remove the battery pack before

removing the dust box. Do not use tool with-

out dust box and HEPA ﬁ lter in place.

CAUTION Keep ﬁ lter clean. Efﬁ ciency of

the HAMMERVAC™ is largely dependent on

the ﬁ lter. A dirty ﬁ lter will reduce the air ﬂ ow

and overall efﬁ ciency of the system. Do not

clean with water or compressed air. Remove

from dust box and tap clean.

Attaching the HAMMERVAC™ to a Rotary

Hammer/Hammer Drill

The HAMMERVAC™ is provided with three clamp-

ing collar assemblies and one side handle grip.

Choose the correct clamping collar assembly for

the tool being used (see Speciﬁ cations). The side

handle grip should be unscrewed from one as-

sembly to be used on another.

1. Turn OFF, remove the battery pack from the

HAMMERVAC™, and disconnect power from

the tool.

2. Remove the tool side handle.

3. Partially screw side handle grip onto clamping

collar assembly

4. Slide the HAMMER-

VAC™ side handle

clamping collar as-

sembly over the

chuck and onto the

neck of the tool. The

clamp lever must be

facing up (3).

5. Attach the side han-

dle clamping collar

assembly onto the

HAMMERVAC™, ﬁ rst

the upper jaw, then

lower jaw.

6. Press down the clamp lever (3) to secure the

clamping collar assembly to the HAMMER-

VAC™.

7. Rotate the HAMMERVAC™ and side handle

grip to the desired position, and tighten securely.

Adjusting the Side Handle Position

1. Loosen the side handle clamping collar assembly

by unscrewing the side handle grip until the side

handle clamping collar assembly rotates freely.

2. Rotate the side handle grip to the desired posi-

tion.

3. Tighten the side handle grip securely.

Installing/Removing the Bit

Slide the bit through the nozzle and then install

into the tool according to the tool manufacturer's

instructions. For best results, use a bit 6" in length

or shorter.

Fitting the HAMMERVAC™ to the Tool and Bit

For proper suction and depth control, position the

nozzle assembly so the bit is ﬂ ush with the for-

ward face of the nozzle:

1. Press and hold the tool and

bit adjustment button.

2. Push in the nozzle assem-

bly until the bit is ﬂ ush with

the front face of the nozzle.

3. Release the tool and bit ad-

justment button.

NOTE: Fully extend the HAM-

MERVAC™ before storing to

preserve spring life.

Setting the Drilling Depth

1. Fit the HAMMERVAC™ to the Tool and Bit.

2. Press and hold the depth gauge button and

slide the depth gauge to the desired depth. The

drilling depth is the last visible measurement

shown when viewed from the top of the tool.

Drill Depth

To ensure the HAMMERVAC™ is properly set

to the tool, bit, and desired depth, always drill

a test hole.

Installing/Removing the

Dust Box and HEPA Filter

To remove the dust box:

1. Turn OFF the tool.

2. Remove the battery pack.

Press the dust box latch down.

4. Pull the dust box away from

the HAMMERVAC™.

5. Empty dust from the dust box.

6. If necessary, pull the HEPA

ﬁ lter away from the dust box

and tap clean. Do not clean

with water or compressed

air. After about 1500 holes or

loss of suction, discard and

replace HEPA ﬁ lter (Cat. No.

49-90-2306).

To install the dust box:

1. Slide the dust box into the body of the HAM-

MERVAC™.

2. The dust box latch should snap into place.

NOTE: Do not operate the HAMMERVAC™ with-

out the dust box and HEPA ﬁ lter in place. Dust box

cannot be installed without HEPA ﬁ lter.

SYMBOLOGY

SPECIFICATIONS

Volts

Underwriters Laboratories, Inc.

United States and Canada

Direct Current

Cat. No. Volts DC

Max. Bit

Diameter

For use with Hammer Collar Sizes

Diameter / Circumference

2306-20 12 5/8" S = Ø 43 mm - 46 mm (1.7"-1.8") / 135 mm - 144.5 mm (5.3"-5.7")

M = Ø 48 mm – 55 mm (1.9"-2.2") / 151 mm - 173 mm (6"-6.9")

L = Ø 56 mm - 59 mm (2.2"-2.3") / 176 mm - 185 mm (6.9"-7.2")

Installing/Removing Nozzle Assembly

To install the nozzle assembly

supplied with the tool, or ac-

cessory nozzles:

1. With the nozzle assembly

pointing straight up, line

up the lugs of the nozzle

assembly with the lugs on

the front of the HAMMER-

VAC™. The unlock symbol

on the nozzle assembly

will line up with the mark on

the top of the HAMMER-

VAC™.

2. Turn the nozzle assembly

left or right to lock into place.

The lock symbol on the

nozzle assembly will line up

with the mark on the top of

the HAMMERVAC™.

3. To remove, reverse the

procedure.

Installing/Removing Nozzle

Replace the nozzle:

• After drilling about 1500 holes,

• When the bit brush shows signs

of wear,

• When suction is reduced,

• When dust escapes through the

bit brush during use

To replace the nozzle (Cat. No.

49-90-2300), press in the release

button and pull out from the lower

nozzle assembly. Slide the new

nozzle into the lower nozzle as-

sembly until it snaps into place.

Correct

Incorrect

6 7

MAINTENANCE

WARNING To reduce the risk of per-

sonal injury and damage, never immerse your

tool, battery pack or charger in liquid or allow

a liquid to ﬂ ow inside them.

WARNING To reduce the risk of injury,

always unplug the charger and remove the

battery pack from the charger or tool before

performing any maintenance. Never disas-

semble the tool, battery pack or charger.

Contact a MILWAUKEE service facility for

ALL repairs.

ACCESSORIES

For a complete listing of accessories refer to your

MILWAUKEE Electric Tool catalog or go online to

www.milwaukeetool.com. To obtain a catalog, con-

tact your local distributor or a service center listed

on the back cover of this operator’s manual.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

Maintaining Tool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

After six months to one year, depending on use,

return the tool, battery pack and charger to a

MILWAUKEE service facility for:

• Lubrication

• Mechanical inspection and cleaning (gears, spin-

dles, bearings, housing, etc.)

• Electrical inspection (battery pack, charger,

motor)

• Testing to assure proper mechanical and

electrical operation

If the tool does not start or operate at full power

with a fully charged battery pack, clean the contacts

on the battery pack. If the tool still does not work

properly, return the tool, charger and battery pack,

to a MILWAUKEE service facility for repairs.

Cleaning

Clean dust and debris from charger and tool

vents. Keep tool handles clean, dry and free of oil

or grease. Use only mild soap and a damp cloth

to clean the tool, battery pack and charger since

certain cleaning agents and solvents are harmful to

plastics and other insulated parts. Some of these

include gasoline, turpentine, lacquer thinner, paint

thinner, chlorinated cleaning solvents, ammonia

and household detergents containing ammonia.

Never use flammable or combustible solvents

around tools.

Repairs

For repairs, return the tool, battery pack and

charger to the nearest service center listed on the

back cover of this operator's manual.

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.

This warranty card covers any defect in material and workmanship on this Power Tool.

To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you pur-

chased the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the

original proof of purchase to the ASC.

Call toll-free 1 800 832 1949 to ﬁ nd the nearest ASC, for service, parts, accessories or components.

Procedure to make this warranty valid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you pur-

chased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all

freight costs relative with this warranty process.

Exceptions

This warranty is not valid in the following situations:

a) When the product is used in a different manners from the end-user guide or instruction manual.

b) When the conditions of use are not normal.

c) When the product was modiﬁ ed or repaired by people not authorized by TECHTRONIC INDUSTRIES.

Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.

SERVICE AND ATTENTION CENTER

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Ph. 52 55 4160-3547

IMPORTED AND COMMERCIALIZED BY:

TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

LIMITED WARRANTY - USA AND CANADA

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN

Model:

Date of Purchase:

Distributor or Store Stamp:

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct

CORDLESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is war-

ranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain

exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is

determined by MILWAUKEE to be defective in material or workmanship for a period of ﬁ ve (5) years* after the

date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center

location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the

proof of purchase should be included with the return product. This warranty does not apply to damage that

MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized

personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and Trade Titan™ Indus-

trial Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED

Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb

fails the Work Light or Upgrade Bulb will be replaced free of charge.

*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline

Driven Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets,

Reconditioned product and Test & Measurement products. There are separate and distinct warranties avail-

able for these products.

Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.

The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is

provided at the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A

CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT

AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MIL-

WAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR

ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE

OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY

CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IN-

CIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN

OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH

IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS

DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.mil-

waukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty

and non-warranty service on a Milwaukee electric power tool.

OPERATION

WARNING To reduce the risk of ﬁ re

and injury, do not use to pick up ﬂ ammable

or combustible materials.

WARNING To reduce the risk of

injury, wear safety goggles or glasses with

side shields and dust mask. Empty dust box

completely before use.

NOTE: When using the optional Crevice Tool ac-

cessory, set the drill depth to 0.

Using the Power Switch

AUTO To set the HAMMERVAC™ to start auto-

matically as a hole is being drilled, move

the power switch to the AUTO position.

When the nozzle assembly is pushed in,

the HAMMERVAC™ will run. NOTE: The

HAMMERVAC™ will continue to run 3-5

seconds after the tool has fully extended

to ensure all dust is captured in dust box.

ON To turn the tool ON, move the power switch

to the ON position. The HAMMERVAC™

will run continuously.

OFF To turn the tool OFF, move the power switch

to the OFF position.

Proper Operation

1. Empty the dust box.

2. Install and position the nozzle assembly to the

desired side.

3. Attach side handle clamping collar assembly

and grip to tool.

4. Fit the HAMMERVAC™ to the Tool and Bit.

5. Set the drill depth.

6. Install the battery pack.

7. Turn HAMMERVAC™ to ON or AUTO.

8. Begin use according to tool manufacturer in-

structions.

9. Always hold the tool securely using both handles

to maintain control.

10. Stop and empty dust box:

• When suction decreases

• When dust begins to come through the bit

brush.

Page is loading ...

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 West Lisbon Road • Brookﬁ eld, Wisconsin, U.S.A. 53005

58-14-2306d2 12/12 Printed in China

961011017-01( )

UNITED STATES

MILWAUKEE Service

CANADA - Service MILWAUKEE

MILWAUKEE prides itself in producing a premium

quality product that is NOTHING BUT HEAVY DUTY

Your satisfaction with our products is very impor-

tant to us!

If you encounter any problems with the operation

of this tool, or you would like to locate the factory

Service/Sales Support Branch or authorized ser-

vice station nearest you, please call...

1.800.268.4015

Monday – Friday 7:00 – 4:30 CST

fax: 866.285.9049

Milwaukee Electric Tool (Canada) Ltd

140 Fernstaff Court, Unit 4 18129 111 Avenue NW

Vaughan, ON L4K 3L8 Edmonton, AB T5S 2P2

Additionally, we have a nationwide network of

authorized Distributors ready to assist you with your

tool and accessory needs. Call 1.800.268.4015 to

ﬁ nd the names and addresses of the closest re-

tailers or consult “Where to buy” on our Web site

www.milwaukeetool.com

MILWAUKEE est ﬁ er de proposer un produit de

première qualité NOTHING BUT HEAVY DUTY

. Votre

satisfaction est ce qui compte le plus!

En cas de problèmes d’utilisation de l’outil ou pour

localiser le centre de service/ventes ou le centre

d’entretien le plus proche, appelez le...

1.800.268.4015

Lundi – Vendredi 7:00 – 4:30 CST

fax: 866.285.9049

Milwaukee Electric Tool (Canada) Ltd

140 Fernstaff Court, Unit 4 18129 111 Avenue NW

Vaughan, ON L4K 3L8 Edmonton, AB T5S 2P2

Notre réseau national de distributeurs agréés se

tient à votre disposition pour fournir l’aide tech-

nique, l’outillage et les accessoires nécessaires.

Composez le 1.800.268.4015 pour obtenir les

noms et adresses des revendeurs les plus proches

ou bien consultez la section «Où acheter» sur notre

site web à l’adresse www.milwaukeetool.com

CENTRO DE ATENCIÓN A CLIENTES

Av Presidente Mazarik 29 Piso 7

11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Telefono 52 55 4160-3547

e-mail: [email protected]

Adicionalmente, tenemos una red nacional de

distribuidores autorizados listos para ayudarle con

su herramienta y sus accesorios. Por favor, llame

al 01 800 832 1949 para obtener los nombres y

direcciones de los más cercanos a usted, o con-

sulte la sección ‘Where to buy’ (Dónde comprar)

de nuestro sitio web en

www.ttigroupmexico.com

MILWAUKEE prides itself in producing a premium

quality product that is NOTHING BUT HEAVY DUTY

Your satisfaction with our products is very impor-

tant to us! If you encounter any problems with the

operation of this tool, or you would like to locate the

factory Service/Sales Support Branch or authorized

service station nearest you, please call...

Additionally, we have a nationwide network of

authorized Distributors ready to assist you with

your tool and accessory needs. Check your “Yellow

Pages” phone directory under “Tools-Electric” for

the names & addresses of those nearest you or see

the 'Where To Buy' section of our website.

1-800-SAWDUST

(1.800.729.3878)

Monday-Friday

7:00 AM - 6:30 PM

Central Time

or visit our website at

www.milwaukeetool.com

For service information, use the 'Service Center

Search' icon found in the 'Parts & Service' section.

Contact our Corporate After Sales Service

Technical Support about ...

•Technical Questions

•Service/Repair Questions

•Warranty

call: 1-800-SAWDUST

fax: 1.800.638.9582

email: [email protected]

www.milwaukeetool.com and...

• receive important notiﬁ cations regarding

your purchase

• ensure that your tool is protected under the

warranty

• become a HEAVY DUTY club member

MEXICO - Soporte de Servicio MILWAUKEE

Registre su herramienta en línea, en

www.ttigroupmexico.com y...

• reciba importantes avisos sobre su compra

• asegúrese de que su herramienta esté prote-

gida por la garantía

• conviértase en integrante de Heavy Duty

Milwaukee M12 HAMMERVAC 2306-20 User manual

Brand: Milwaukee

Model: M12 HAMMERVAC 2306-20

Category: Rotary hammers

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Milwaukee M12 HAMMERVAC 2306-20 Manuel utilisateur
español: Milwaukee M12 HAMMERVAC 2306-20 Manual de usuario

Milwaukee M12 HAMMERVAC 2306-20 User manual

This manual is also suitable for

Milwaukee M12 HAMMERVAC 2306-20 User manual

in other languages

Related papers

Other documents