Magtek DynaWave User manual

MagTek I 1710 Apollo Court I Seal Beach, CA 90740 I Phone: (562) 546-6400 I Technical Support: (888) 624-8350

www.magtek.com

mDynamo and DynaWave

Update and Test Baud Rate - Remote Services v2.0

Installation and Operation Guide

January 7, 2021

Document Number:

D998200351-20

REGISTERED TO ISO 9001:2015

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 2 of 11 (D998200351-20)

Printed in the United States of America

INFORMATION IN THIS PUBLICATION IS SUBJECT TO CHANGE WITHOUT NOTICE AND

MAY CONTAIN TECHNICAL INACCURACIES OR GRAPHICAL DISCREPANCIES. CHANGES

OR IMPROVEMENTS MADE TO THIS PRODUCT WILL BE UPDATED IN THE NEXT

PUBLICATION RELEASE. NO PART OF THIS DOCUMENT MAY BE REPRODUCED OR

TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC OR MECHANICAL, FOR

ANY PURPOSE, WITHOUT THE EXPRESS WRITTEN PERMISSION OF MAGTEK, INC.

MagTek® is a registered trademark of MagTek, Inc.

MagnePrint® is a registered trademark of MagTek, Inc.

Magensa™ is a trademark of MagTek, Inc.

MagneSafe® is a registered trademark of MagTek, Inc

DynaPro™ and DynaPro Mini™, are trademarks of MagTek, Inc.

ExpressCard 2000 is a trademark of MagTek, Inc.

IPAD® is a trademark of MagTek, Inc.

IntelliStripe® is a registered trademark of MagTek, Inc.

Google Play™ store, Google Wallet™ payment service, and Android™ platform are trademarks of

Google Inc.

Apple Pay®, iPhone®, iPod®, Mac®, and OS X® are registered trademarks of Apple Inc., registered in

the U.S. and other countries. iPad™ is a trademark of Apple. Inc. App Store

SM

is a service mark of

Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of

Cisco in the U.S. and other countries and is used by Apple Inc. under license.

Microsoft®, Windows®, and .NET® are registered trademarks of Microsoft Corporation.

All other system names and product names are the property of their respective owners.

Table 0-1 - Revisions

Rev Number

Date

Notes

10

Nov 13, 2019

Initial Release

11 Dec 29, 2020

Corrected Magtek Reader Config App Hyperlink and

12

Jan 7, 2021

Update template to MagTek

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 3 of 11 (D998200351-20)

SOFTWARE LICENSE AGREEMENT

IMPORTANT: YOU SHOULD CAREFULLY READ ALL THE TERMS, CONDITIONS AND

RESTRICTIONS OF THIS LICENSE AGREEMENT BEFORE INSTALLING THE SOFTWARE

PACKAGE. YOUR INSTALLATION OF THE SOFTWARE PACKAGE PRESUMES YOUR

ACCEPTANCE OF THE TERMS, CONDITIONS, AND RESTRICTIONS CONTAINED IN THIS

AGREEMENT. IF YOU DO NOT AGREE WITH THESE TERMS, CONDITIONS, AND

RESTRICTIONS, PROMPTLY RETURN THE SOFTWARE PACKAGE AND ASSOCIATED

DOCUMENTATION TO THE ADDRESS ON THE FRONT PAGE OF THIS DOCUMENT,

ATTENTION: CUSTOMER SUPPORT.

TERMS, CONDITIONS, AND RESTRICTIONS

MagTek, Incorporated (the "Licensor") owns and has the right to distribute the described software and

documentation, collectively referred to as the "Software."

LICENSE: Licensor grants you (the "Licensee") the right to use the Software in conjunction with

MagTek products. LICENSEE MAY NOT COPY, MODIFY, OR TRANSFER THE SOFTWARE IN

WHOLE OR IN PART EXCEPT AS EXPRESSLY PROVIDED IN THIS AGREEMENT. Licensee

may not decompile, disassemble, or in any other manner attempt to reverse engineer the Software.

Licensee shall not tamper with, bypass, or alter any security features of the software or attempt to do so.

TRANSFER: Licensee may not transfer the Software or license to the Software to another party without

the prior written authorization of the Licensor. If Licensee transfers the Software without authorization,

all rights granted under this Agreement are automatically terminated.

COPYRIGHT: The Software is copyrighted. Licensee may not copy the Software except for archival

purposes or to load for execution purposes. All other copies of the Software are in violation of this

Agreement.

TERM: This Agreement is in effect as long as Licensee continues the use of the Software. The Licensor

also reserves the right to terminate this Agreement if Licensee fails to comply with any of the terms,

conditions, or restrictions contained herein. Should Licensor terminate this Agreement due to Licensee's

failure to comply, Licensee agrees to return the Software to Licensor. Receipt of returned Software by

the Licensor shall mark the termination.

LIMITED WARRANTY: Licensor warrants to the Licensee that the disk(s) or other media on which

the Software is recorded are free from defects in material or workmanship under normal use.

THE SOFTWARE IS PROVIDED AS IS. LICENSOR MAKES NO OTHER WARRANTY OF ANY

KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Because of the diversity of conditions and PC hardware under which the Software may be used, Licensor

does not warrant that the Software will meet Licensee specifications or that the operation of the Software

will be uninterrupted or free of errors.

IN NO EVENT WILL LICENSOR BE LIABLE FOR ANY DAMAGES, INCLUDING ANY LOST

PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES

ARISING OUT OF THE USE, OR INABILITY TO USE, THE SOFTWARE. Licensee's sole remedy in

the event of a defect in material or workmanship is expressly limited to replacement of the Software

disk(s) if applicable.

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 4 of 11 (D998200351-20)

GOVERNING LAW: If any provision of this Agreement is found to be unlawful, void, or

unenforceable, that provision shall be removed from consideration under this Agreement and will not

affect the enforceability of any of the remaining provisions. This Agreement shall be governed by the

laws of the State of California and shall inure to the benefit of MagTek, Incorporated, its successors or

assigns.

ACKNOWLEDGMENT: LICENSEE ACKNOWLEDGES THAT HE HAS READ THIS

AGREEMENT, UNDERSTANDS ALL OF ITS TERMS, CONDITIONS, AND RESTRICTIONS, AND

AGREES TO BE BOUND BY THEM. LICENSEE ALSO AGREES THAT THIS AGREEMENT

SUPERSEDES ANY AND ALL VERBAL AND WRITTEN COMMUNICATIONS BETWEEN

LICENSOR AND LICENSEE OR THEIR ASSIGNS RELATING TO THE SUBJECT MATTER OF

THIS AGREEMENT.

QUESTIONS REGARDING THIS AGREEMENT SHOULD BE ADDRESSED IN WRITING TO

MAGTEK, INCORPORATED, ATTENTION: CUSTOMER SUPPORT, AT THE ADDRESS LISTED

IN THIS DOCUMENT, OR E-MAILED TO [email protected].

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 5 of 11 (D998200351-20)

Table of Contents

SOFTWARE LICENSE AGREEMENT ................................................................................................................. 3

Table of Contents .............................................................................................................................................. 5

1 The purpose of this document ................................................................................................................ 6

2 Connect to MagTek Reader Configuration App ................................................................................... 6

3 Disconnect from the MagTek Reader Configuration App. ................................................................. 7

4 Connect to OEM Demo App ..................................................................................................................... 8

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 6 of 11 (D998200351-20)

1 The purpose of this document

These instructions explain how to change the Baud Rate for mDynamo using the Windows version of the

MagTek Reader Configuration App (RS2/Remote Services). It will also explain how to test the

DynaWave after properly configuring the baud rates for both devices.

2 Connect to MagTek Reader Configuration App

Download the MagTek Reader Configuration App

Launch the MagTek Reader Configuration App.

Connect mDynamo via USB.

Once the device is detected, it will show its device details in the upper right corner.

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 7 of 11 (D998200351-20)

Select mDynamo UART 115200 in the drop down for Reader Config Options.

Make sure the Key is set to “Current Key”.

Press the Change Config button.

When complete, the main dialog box will indicate that the Configuration was “Successfully Changed”.

3 Disconnect from the MagTek Reader Configuration App.

Disconnect from the MagTek Reader Configuration App.

Please power cycle the mDynamo.

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 8 of 11 (D998200351-20)

4 Connect to OEM Demo App

Download the MTSCRA OEM Demo App

Launch the MTSCRA OEM Demo App.

Connect mDynamo via USB and select NFC module in the UART Port drop-down list.

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 9 of 11 (D998200351-20)

Press the Connect button.

Press the Set Time button.

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 10 of 11 (D998200351-20)

Select Contactless Card in the Transaction Type drop-down list.

Press the Start button to begin an EMV transaction.

“Present Card” will appear in the main dialog box at the top of the screen.

mDynamo and DynaWave| Update and Test Baud Rate - Remote Services v2.0 | Installation and Operation Guide

Page 11 of 11 (D998200351-20)

Hold a Contactless EMV Card or NFC token/phone near the DynaWave.

After the data is acquired and transmitted to the app via the DynaWave, a message will be appear in the

main dialog box at the top of the screen.

Magtek DynaWave User manual

This manual is also suitable for

Magtek DynaWave User manual

Related papers

Other documents