2. Mettler Toledo
  3. EasyMax

Mettler Toledo EasyMax Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Mettler Toledo EasyMax Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
iControl
™
Quick Start Guide
Connecting EasyMax
™
/OptiMax
™
with iControl
™
1
Step 1 – Install iControl
™
Step 2 – Two Ways to Link Your Instrument and PC
1
Connect your instrument and
PC directly with a network cable.
2
Or connect your instrument
and PC via the Corporate Intranet.
Connect instrument and PC through
a free network plug.
Corporate
Intranet
iControl
™
Software Version 5.1
Mettler-Toledo AutoChem, Inc.
7075 Samuel Morse Drive,
Columbia, MD 21046 USA
Mettler-Toledo AG, AutoChem
Sonnenbergstrasse 74,
CH-8603 Schwerzenbach, Switzerland
www.mt.com/iControl
© 10/2011 Mettler-Toledo AG
2
Establish a connection between your instrument and PC following this step-by-step guide.
Quick Start Guide
Step 3 – Configure Touchscreen
Go to “Device
Settings” by pressing the button on
the top right corner. Press “Network
Settings”, then go to “LAN Settings”.
Enter the following:
DHCP Disabled
IP-Address 192.168.0.1
Subnet Mask 255.255.255.0
Please proceed to Step 4.
Make certain that DHCP is set to “Enabled” and note
the IP Address. We need it later to enter it in iControl
™
.
Please skip steps 4-7 and proceed to Step 8.
Press button
1
Direct Cable Connection
2
Connection via Corporate Intranet
Step 4 – Windows 7, Vista or XP User
I am a Windows XP user.
Type “ncpa.cpl” in “Run” dialog to open network
settings. Press “OK”.
Step 5 – Local Area Connection
Double click “Local Area Connection”.
Step 6 – Properties & Internet Protocol
Press “Properties”, then
double click “Internet
Protocol (TCP/IP)”.
Step 7 – IP Address
Enter 192.168.0.2 as
IP address.
Press “OK” 2 times
and then “Close”.
I am a Windows 7 or Vista user.
Type “ncpa.cpl” in “Start” menu.
Click “ncpa.cpl” from the “Programs” list.
Double click “Local Area Connection”.
Press “Properties”, then
double click “Internet
Protocol (TCP/IPv4)”.
Enter 192.168.0.2 as
IP address.
Press “OK” 2 times
and then “Close”.
1
Step 4 – 7 need to be performed only if you have a direct cable connection between
your instrument and PC.
2
If you connect via the Corporate Intranet, you can proceed directly to Step 8.
Quality certicate. Development,
production and testing according to ISO
90 01.
Environmental man agement system
according to ISO 14001.
European conformity. The CE conformity
mark provides you with the assurance that
our products comply with the EU directives.
For more Information
www.mt.com/iControl
Mettler-Toledo AG, AutoChem
Sonnenbergstrasse 74
CH-8603 Schwerzenbach, Switzerland
Phone +41-44 806 75 65
Fax +41-44 806 72 90
Mettler-Toledo AutoChem, Inc.
7075 Samuel Morse Drive
Columbia, MD 21046, USA
Phone +1-410 910 8500
Fax +1-410 910 8600
Internet www.mt.com/iC
E-mail [email protected]
Subject to technical changes.
© 11/2011 Mettler-Toledo AG
Printed in Switzerland
51710672B
Step 8 – Set and Test Your Connection in iControl
™
Press “Configure Instruments”
on the Start Page and add an
instrument.
1
If you use a direct cable
connection, enter 192.168.0.1 as
instrument IP address. Then press
“Save”.
2
If you connect via the Corpo-
rate Intranet, enter the instrument
IP address from Step 3. Then press
“Save”.
Press the “Test connection” button
to test the connection to the
instrument. Then press “Close”.
Congratulations
You have configured iControl
™
.
Quick Start Guide
Connecting EasyMax
™
/OptiMax
™
with iControl
™
/