TVT TD-9423E3 is a versatile surveillance camera that offers a range of features to meet your security needs. With its motorized zoom lens, you can adjust the field of view remotely to capture a wide area or focus on specific details. The camera also supports PoE (Power over Ethernet), allowing you to transmit both power and data over a single network cable, simplifying installation and reducing wiring costs.
TVT TD-9423E3 is a versatile surveillance camera that offers a range of features to meet your security needs. With its motorized zoom lens, you can adjust the field of view remotely to capture a wide area or focus on specific details. The camera also supports PoE (Power over Ethernet), allowing you to transmit both power and data over a single network cable, simplifying installation and reducing wiring costs.
Package
Overview
Installation
1
2
3
4
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Quick Start Guide
Network Camera
Camera
Quick start guide
CD
Plastic plug ×4
Drill template
CVBS&DC
IN cables
Screwdriver
4 tapping screws PA4×25
1 machine screw PWM3×5
●
Alarm Input: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port of the camera.
Alarm Output: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
COM and OPEN separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
● Connecting Network Cable
Alarm Connection
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
2
1
3
7
8A
8B
9A
9B
10
11
7
10
11
Type A: Motorized zoom camera
Type B: Manual zoom camera
1 Ethernet Connector *
2 Audio Input (
3 Audio Output (
4 CVBS Video Output
5 Alarm Input/Output
6 Power Connector *
7 Micro SD Card Slot
8A Zoom +
9A Zoom -
8B Focus
9B Zoom
10 DC IN & CVBS Interface
11 Reset
MIC)
HP)
* 1
* 2 This series can be powered by DC 12V/PoE power supply. If the PoE switch is
used to power the camera, DC12V power supply is not required.
It is recommended to install the security cap for outdoor installation.
1
3
4
5
6
2
AL
ARM
4 3 2 1
S
e
c
uri
t
y c
ap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
ALAR M
4 3 2 1
Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router
Computer
● Access Through IP-Tool
Here we take accessing IP camera via LAN for example.
① Make sure that the camera and the PC are well connected to the
LAN.
② Find the IP-Tool from the CD and then install it in the computer.
After that, run the IP-Tool as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the ad ministrator password, and
then modify the network parameters.
Total Device: 3
Local IP Address:192.168.1.4
Subnet Mask:255. 255. 255. 0 Gateway: 192.168.1.1 DNS：210. 21.196.6
Device Name Device Type IP Address Http Port Data Port
Subnet
Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please enter the password of the administrator and click
“Modify” button to modify the setting.
The default password of the administrator is “123456”.
④ Double-click the IP address to open up the web browser or
manually enter the modified IP address in the address bar of your
browser. Then follow directions to download and install the plugin if
it is the first time for you to log in.
the user name and password in the login interface.
The default username is admin; the default password is 123456.
⑤ Enter
450043001289 A0
Mounting Base
Insert a micro
SD card
④ Bracket adjustment. Before adjustment, preview the image of the
camera on a monitor (See the left figure of step ⑤) and then loosen the
fixed screws to adjust the view angle of the camera. After that, tighten
the fixed screws.
64.6mm
64.6mm
∅5
② Route the cables and connect the relevant cables.
③ Fasten the mounting base to the wall with the screws provided.
Fixed Screws
Pan 360°
Tilt 90°
Rotate
360°
Type A: Motorized zoom camera
Type B: Manual zoom camera
Zoom
Zoom+
Zoom-
Monitor
Focus
⑥
screws. ( )
Install the cover back to the camera and fix it with the firmly
Note that the cover should not be installed unevenly.
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install the camera
in the dry environment. You'd better install back the cover
of the camera less than 4 hours after removing it.
① Drill the screw holes and the cable hole (if you want to route
through the ceiling) on the wall or ceiling according to the drill
template.
Cover
⑤
and then insert a micro SD card. After that, adjust Zoom or Focus
to obtain an optimum image. Press the T or W button for Type A;
adjust the Focus and Zoom screws for Type B. Before adjustment,
view the image of the camera on a monitor.
Open the cover of the camera as shown in the following figure
-
1
-
2
TVT TD-9423E3 is a versatile surveillance camera that offers a range of features to meet your security needs. With its motorized zoom lens, you can adjust the field of view remotely to capture a wide area or focus on specific details. The camera also supports PoE (Power over Ethernet), allowing you to transmit both power and data over a single network cable, simplifying installation and reducing wiring costs.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
WorldEyeCam TD-9554C1 User guide
-
-
-
WorldEyeCam TD-9421S3 User guide
-
WorldEyeCam TD-9584S2 User guide
-
-
-
-
-