Allied Telesis AT-PWR10 Installation guide

Brand: Allied Telesis

Model: AT-PWR10

Type: Installation guide

Allied Telesis AT-PWR10 is an AC redundant power supply for the AT-8400 Series switch. When installed, the unit operates in a standby mode. If the standard power supply fails or loses power, the AT-PWR10 unit changes from standby to active and provides all power to the system to prevent a network failure. The AT-PWR10 unit must be installed in an AC powered AT-8400 Series switch. This type of chassis has two AC power sockets on the back panel. There may be several different models of AC power supplies for the AT-8400 Series switch. Each model is rated for a different power load.

Overview

The AT-PWR10 is an AC redundant power supply for the AT-8400 Series switch.

When installed, the unit operates in a standby mode. If the standard power supply

fails or loses power, the AT-PWR10 unit changes from standby to active and

provides all power to the system to prevent a network failure.

Note

The power supply is hot-swappable. You can install it without powering off

the AT-8400 Series switch.

AT-PWR10

NIN

BEFORE

EJECTING,

LOOSEN

THUMBSCREW

Related Documents

The Allied Telesyn web site at www.alliedtelesyn.com contains the most recent

documentation, software, and technical information on all of our products. For

details on the features and functions of your Allied Telesyn AT-8400 Series switch

and line cards, refer to the following manuals from our web site:

❑ AT-8400 Series Switch Reference Guide

PN 613-50399-00

❑ AT-S60 Management Software User’s Guide

PN 613-50400-00

❑ AT-S60 Command Line User’s Guide

PN 613-50401-00

Package Contents

Make sure the following items are included in the shipping package. If any item is

missing or damaged, contact your Allied Telesyn sales representative for

assistance.

❑ One AT-PWR10 Redundant Power Supply (AC)

❑ Installation Guide

❑ Warranty Card

The AC power cord for this power supply comes with the AT-8400 chassis.

Note

To replace a power supply, refer to the AT-8400 Series Switch Reference Guide

for instructions on how to remove a power supply from the chassis.

Installing the AT-PWR10 Power Supply

Before installing a power supply, please note the following:

❑ Refer to the AT-8400 Series Switch Reference Guide for electrical safety and

emission information.

❑ The AT-PWR10 unit must be installed in an AC powered AT-8400 Series

switch. This type of chassis has two AC power sockets on the back panel.

❑ There may be several different models of AC power supplies for the

AT-8400 Series switch. Each model is rated for a different power load.

Both power supplies in an AT-8400 Series switch must be of the same

model type. Do not mix power supplies with different power ratings in

the same chassis.

To install the AT-PWR10 unit, follow these steps:

1. Using a Phillips screwdriver, loosen the two captive screws that secure the

power supply cover to the chassis and remove the cover. You remove the cover

by angling it from the bottom as you slide it down and out of the chassis.

2. Using a Phillips screwdriver, loosen the captive screw that secures the cover

over the power supply PWR B slot and slide the cover from the chassis.

Note

Store the cover in a safe place. You must reinstall it if you ever remove a power

supply from the chassis without installing a new one.

AT-8411

AT-84 11

AT-PWR10

AT-84 11

100

AT-84 11

100

AT-84 11

ACT

100

WARN

BEFORE

EJECTING,

LOOSEN

THUMBSCREW

AT-PWR10

Redundant Power Supply (AC)

Installation Guide

Allied Telesyn, Inc.

960 Stewart Drive, Suite B

Sunnyvale, CA 94085 USA

Tel 1 (408) 730-0950 • Fax 1 (408) 736-0100

Visit our web site at: www.alliedtelesyn.com

PN 613-50394-00 Rev B

1 2 3

3. Place the locking levers on the new AT-PWR10 power supply in the released

position.

4. Slide the new AT-PWR10 power supply into the power supply slot until it makes

contact with the backplane of the chassis. Be sure that the labeling on the

power supply is right-side up. Also be sure to align the green board on the

power supply with the slots in the chassis. Once the power supply makes

contact with its connector on the backplane, press firmly to fully seat the power

supply on the power connector.

Note

If you are unable to slide the power supply completely into the slot, you may

have purchased the wrong type of power supply for the chassis. An AC

powered chassis has two AC power sockets on the back panel.

AT-PWR10

NIN

BEFOR

EJECTING,

LOOSE

THUMB

SCREW

AT-PW

AT-8 411

100

AT-8 411

100

AT-8 411

100

AT-P W

WARN

ING

BEFORE

EJECTING,

LOOSEN

THUMBSCREW

5. Move the locking levers on the AT-PWR10 unit into the locked position and

tighten the captive screw to secure the power supply in the chassis.

Note

Always use the locking levers and the installation screw to secure the power

supply to the switch. Leaving the power supply partially seated may cause the

system to halt and subsequently crash.

6. Connect an AC power cord to the POWER B power connector on the back panel

on the chassis and secure the cord by lowering the securing bracket.

7. Connect the other end of the power cord to an appropriate power source.

8. Check the POWER LED on the front of the power supply. It should be steady

green. If the LED remains off, reinstall the unit by repeating this procedure.

AT-PWR10

AT-PWR11

WARNING

BEFORE

EJECTING,

LOOSEN

THUMBSCREW

WARNING

BEFORE

EJECTING,

LOOSEN

THUMBSCREW

FAN A

PWR BPWR A

FAN A

PWR B PWR

WARNING

This unit might have more

than one power cord. To

reduce the risk of electric

shock, disconnect all

power cords before

servicing unit.

WARNING

This unit might

have more

than one power cord.

reduce the risk

of electric

shock,

disconnect all

power cords before

servicing

unit.

9. Slide the power supply cover back into the chassis and secure the cover by

tightening the two captive screws.

Technical Specifications

Power Specifications: 100-240V AC, 3A maximum, 50/60 Hz

Maximum Operating Temperature: 0° C to 40° C (32° F to 104° F)

Maximum Storage Temperature: -20° C to 80° C (-4° F to 176° F)

Operating and Storage Altitude: Up to 3,048 meters (10,000 feet)

Relative Humidity Operating

and Storage: 5% to 80% (non-condensing)

Electrical Safety and Emission Statement

Standards: This product meets the following standards when installed in compliant host equipment.

Emission FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, VCCI Class A, C-TICK

WARNING: In a domestic environment this product may cause radio interference in which case the user may be

required to take adequate measures.

Immunity EN55024

Electrical Safety UL60950 (UL/cUL), EN60950 (TUV)

No part of this publication may be reproduced without prior written permission from Allied Telesyn Inc.

U.S. Federal Communications Commission

RADIATED ENERGY

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to

Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to

operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du

Canada.

AT-8411

EJECT

LNK

AT-8411

EJEC

LNK

4 5 6

Allied Telesis AT-PWR10 Installation guide

Allied Telesis AT-PWR10 Installation guide

Allied Telesis AT-PWR10 Installation guide

Related papers

Other documents