Bosch EXTEGRA IP 9000 FX NXF-9x30 Installation guide

EXTEGRA IP 9000 FX

NXF-9x30

Installation Manual / Manuel d'installation

english

français

Table of contents

1

Safety 4

1.1 About this Manual 4

1.2 Legal Information 4

1.3 Safety Precautions 4

1.4 Important Safety Instructions 5

1.5 FCC & ICES compliance 6

1.6 UL Certification 7

1.7 Explosion Protected Certifications 7

1.8 Joint Information 8

1.9 Warranty / Limitation of Liability 9

1.10 Customer Support and Service 10

2

Product Description 11

2.1 Unpacking 11

2.2 Parts List 12

2.2.1 Parts Included with the Product 12

2.2.2 User-supplied Parts 12

3

Planning 13

3.1 Dimensional Drawings 13

3.2 Initial Preparations 14

4

Installation Overview 15

5

Install the Optional Media Storage Card 17

6

Connections 20

6.1 Power Cable Requirements 20

6.1.1 Wire Distance Guide 20

6.2 Ethernet Cable Requirements 20

6.3 Alarm Cable Requirements 21

6.4 Audio Cable Requirements 21

6.5 Making the Connections 21

7

Mounting 24

7.1 Mounting the Unit 24

7.2 Installing the Sunshield 26

8

Troubleshooting 27

8.1 Function Test 27

8.2 Resolving Problems 27

8.3 Customer Service 28

9

Maintenance 29

9.1 Repairs 29

9.2 Replacement of the Mounting Cradle 29

10

Decommissioning 30

EXTEGRA IP 9000 FX Table of Contents | en

3

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

Safety

About this Manual

This manual has been compiled with great care and the information it contains has been

thoroughly verified. The text was complete and correct at the time of printing. Because of the

ongoing development of products, the content of the manual may change without notice.

Bosch Security Systems accepts no liability for damage resulting directly or indirectly from

faults, incompleteness, or discrepancies between the manual and the product described.

Legal Information

Copyright

This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by

Trademarks

All hardware and software product names used in this document are likely to be registered

trademarks and must be treated accordingly.

Safety Precautions

In this manual, the following symbols and notations are used to draw attention to special

situations:

Danger!

High risk: This symbol indicates an imminently hazardous situation such as “Dangerous

Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily

injury, or death.

!

Warning!

Medium risk: Indicates a potentially hazardous situation. If not avoided, this may result in

minor or moderate injury.

!

Caution!

Low risk: Indicates a potentially hazardous situation. If not avoided, this may result in

property damage or risk of damage to the unit.

Notice!

This symbol indicates information or a company policy that relates directly or indirectly to the

safety of personnel or protection of property.

1

1.1

1.2

1.3

4

en | Safety EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Important Safety Instructions

Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit

and in the operating instructions before operation.

!

Caution!

TO REDUCE THE RISK OF ELECTRIC SHOCK, DISCONNECT THE POWER SOURCE WHILE

INSTALLING THE CAMERA.

!

Caution!

Installation must be made by qualified personnel and conform to ANSI/NFPA 70 (the National

Electrical Code

®

(NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1),

and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for any

damages or losses caused by incorrect or improper installation.

!

Warning!

INSTALL EXTERNAL INTERCONNECTING CABLES IN ACCORDANCE TO NEC, ANSI/NFPA70

(FOR US APPLICATION) AND CANADIAN ELECTRICAL CODE, PART I, CSA C22.1 (FOR CAN

APPLICATION) AND IN ACCORDANCE TO LOCAL COUNTRY CODES FOR ALL OTHER

COUNTRIES. BRANCH CIRCUIT PROTECTION INCORPORATING A 20 A, 2-POLE LISTED

CIRCUIT BREAKER OR BRANCH RATED FUSES ARE REQUIRED AS PART OF THE BUILDING

INSTALLATION. A READILY ACCESSIBLE 2-POLE DISCONNECT DEVICE WITH A CONTACT

SEPARATION OF AT LEAST 3 mm MUST BE INCORPORATED.

Adjustment of controls - Adjust only those controls specified in the operating instructions.

Improper adjustment of other controls may cause damage to the unit.

Power cord and plug protection - Protect the power cord from being walked on or pinched,

particularly at plugs, and at the point of exit from the device.

For units intended to operate with 230 VAC, 50 Hz, the input and output power cord must

comply with the latest versions of IEC Publication 227 or IEC Publication 245.

Power disconnect - Units with or without ON/OFF switches have power supplied to the unit

whenever the power cord is inserted into the power source; however, the unit is operational

only when the ON/OFF switch is in the ON position. The power cord is the main power

disconnect device for switching off the voltage for all units.

HPoE: Use only approved HPoE devices. High Power-over-Ethernet can be connected at the

same time as a 24 VAC power supply.

If auxiliary power (24 VAC) and HPoE are applied simultaneously, the camera selects auxiliary

input and shuts off the HPoE.

Servicing - Do not attempt to service this device yourself. Refer all servicing to qualified

service personnel.

1.4

EXTEGRA IP 9000 FX Safety | en

5

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

FCC & ICES compliance

FCC & ICES Information

(U.S.A. and Canadian Models Only)

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions:

– this device may not cause harmful interference, and

– this device must accept any interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These

limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and

radiates radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference, in which case the

user will be required to correct the interference at his expense.

Intentional or unintentional modifications, not expressly approved by the party responsible for

compliance, shall not be made. Any such modifications could void the user's authority to

operate the equipment. If necessary, the user should consult the dealer or an experienced

radio/television technician for corrective action.

The user may find the following booklet, prepared by the Federal Communications

Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This

booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock

No. 004-000-00345-4.

Informations FCC et ICES

(modèles utilisés aux États-Unis et au Canada uniquement)

Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux

conditions suivantes :

– cet appareil ne peut pas provoquer d'interférence nuisible et

–

cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y

compris les interférences qui pourraient influer sur son bon fonctionnement.

AVERTISSEMENT: Suite à différents tests, cet appareil s’est révélé conforme aux exigences

imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la

Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont

destinées à fournir une protection raisonnable contre les interférences nuisibles quand

l'appareil est utilisé dans une installation commerciale. Cette appareil génère, utilise et émet

de l'energie de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme aux

instructions, générer des interférences nuisibles aux communications radio. L’utilisation de ce

produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas

échéant, l’utilisateur devra remédier à ces interférences à ses propres frais.

Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision,

qui procédera à une opération corrective. La brochure suivante, publiée par la Commission

fédérale des communications (FCC), peut s’avérer utile : How to Identify and Resolve Radio-TV

Interference Problems (Comment identifier et résoudre les problèmes d’interférences de radio

et de télévision). Cette brochure est disponible auprès du U.S. Government Printing Office,

Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.

1.5

6

en | Safety EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

UL Certification

UL Disclaimer

Underwriter Laboratories Inc. ("UL") has not tested the performance or reliability of the

security or signaling aspects of this product. UL has only tested fire, shock and/or casualty

hazards as outlined in Standard(s) for Safety for Information Technology Equipment, UL

60950-1 . UL Certification does not cover the performance or reliability of the security or

signaling aspects of this product.

UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER

REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATED

FUNCTIONS OF THIS PRODUCT.

Explosion Protected Certifications

Camera for Use in Hazardous Locations

Bosch Security Systems B.V.

NXF-9x30 camera models

24 VAC, Class 2, maximum 68 W (85 VA) (with heaters)

HPoE maximum 48 W (50 VA) (with heaters)

File # E333679

Class I, Groups C and D; Class II, Groups E, F, and G; Class III

Class I, Zone 1, AEx d IIB T6

; Ex d IIB T6 X

AEx tb IIIC T85°C Db

Ex tb IIIC T85°C Db X

IP68, Type 4X, Type 6P

ATEX Certification

DEMKO 15 ATEX 1444X

0539 II 2 GD

IECEx Certification

IECEx UL 15.0001X

Ex d IIB T6 Gb; Ex tb IIIC T85°C Db

Relevant standards associated with the ATEX and IECEx certifications.

EN 60079-0:2012+A11:2013

EN 60079-1:2007

EN 60079-31:2009

IEC 60079-1:2011 Edition 6

IEC 60079-1:2007-04 Edition 6

IEC 60079-31:2008 Edition 1

1.6

1.7

EXTEGRA IP 9000 FX Safety | en

7

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

Joint Information

To obtain more information about the flameproof joints, please contact Bosch Security

Systems.

Joint-Threaded (All Models) Designation Pitch Full Threads

Engaged

Depth of

Engagement

Back Cover to Junction Box M 103 1.5 mm 7 minimum 14.5 mm

Housing to Junction Box M 103 2 mm 7 minimum 18.5 mm

Supply Opening Blanking Element to

Junction Box (four openings

provided)

3/4-14 NPT N/A 5 N/A

Housing to Front Cover M 103 2 mm 8 minimum 19.5 mm

!

Warning!

To reduce the risk of ignition of hazardous atmospheres, conduit runs must have a sealing

fitting connected to the wall of the enclosure.

!

Warning!

DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT.

1.8

8

en | Safety EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Warranty / Limitation of Liability

The unit has a 3 year warranty.

BOSCH Security Systems warrants that its products, at the time of shipment by BOSCH

Security Systems, are free from defect in material or workmanship under normal use and

service for the respective warranty periods specified in the applicable Price Schedule or as

otherwise published.

To assure conformance with operating limitations, Buyer should refer to the applicable data

sheet.

The warranty is void (i) if the Product is not operated in conformance with installation,

environmental, mechanical or electrical requirements, or within thermal stress limits, or (ii) to

the extent that any malfunction is the result of misuse, abuse, vandalism, neglect, improper

installation or application, alteration, accident, or negligence in use, storage, transportation,

or handling or if the original identification markings on the product have been removed,

defaced or altered, lightning, electricity, water, fire, environment or other hazard, or act of

God, or other impact outside of normal operating guidelines.

The foregoing warranty is subject to Buyer’s (i) promptly written claim and (ii) timely provision

to BOSCH Security Systems of an opportunity to inspect and test the Product claimed to be

defective. Such inspection may be on Buyer’s premises and/or BOSCH Security Systems may

request the return of the Product at Buyer’s expense. However, BOSCH Security Systems shall

not be responsible for packing, inspection, or labor costs in connection with the return of

Product. No Product shall be accepted for warranty service that is not accompanied by a

Return Authorization issued by BOSCH.

The liability of BOSCH Security Systems hereunder or otherwise is solely and exclusively

limited to replacement (new or refurbished Product), repair, or credit of the amortized

purchase price, as BOSCH Security may elect, for any Product which is returned by Buyer

during the applicable warranty period, or services for which timely notice of defect has been

given by Buyer, and which are found by BOSCH Security to be subject to adjustment under

this warranty.

BOSCH Security System’s warranty shall not be enlarged, diminished, or affected by, and no

obligation or liability shall arise or grow out of BOSCH Security’s rendering or technical

advice, facilities, or services in connection with Buyer’s order to the products furnished

hereunder.

For more information about the warranty on this product, see the Warranty Repair section on

Bosch’s Customer Care web page at www.boschsecurity.us/en-us/Service/CustomerCare.

1.9

EXTEGRA IP 9000 FX Safety | en

9

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

Customer Support and Service

If this unit needs service, contact the nearest Bosch Security Systems Service Center for

authorization to return and shipping instructions.

Service Centers

USA

Telephone: 800-366-2283 or 585-340-4162

Fax: 800-366-1329

Email: [email protected]

Customer Service

Telephone: 888-289-0096

Fax: 585-223-9180

Email: [email protected]

Technical Support

Telephone: 800-326-1450

Fax: 585-223-3508 or 717-735-6560

Email: [email protected]

Repair Center

Telephone: 585-421-4220

Fax: 585-223-9180 or 717-735-6561

Email: [email protected]

Canada

Telephone: 514-738-2434

Fax: 514-738-8480

Europe, Middle East & Africa Region

Please contact your local distributor or Bosch sales office. Use this link:

http://www.boschsecurity.com/startpage/html/europe.htm

Asia Pacific Region

Please contact your local distributor or Bosch sales office. Use this link:

http://www.boschsecurity.com/startpage/html/asia_pacific.htm

More Information

For more information please contact the nearest Bosch Security Systems location or visit

www.boschsecurity.com

1.10

10

en | Safety EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Product Description

The EXTEGRA IP 9000 is a high-performance, smart surveillance camera for explosive

environments. The camera offers unrivaled image quality in the worst lighting conditions. A

single pre-assembled unit with an integrated junction box, the camera is designed to be easy

to install. Through any of the four (4) 3/4 in. conduit entries, connections are made to the

convenient terminal connector; there is also space for any additional wiring.

The camera supports Power over Ethernet (HPoE, IEEE 802.3at, class 2) compliant network

cable connection and a 24 VAC power supply. You can connect both power sources

simultaneously for additional system reliability.

Both camera variants--

EXTEGRA IP starlight 9000 FX (NXF-9130) and EXTEGRA IP dynamic

9000 FX (NXF-9230)—have a professional-grade imaging platform with a 30x optical zoom (12x

digital) lens capable of delivering HD resolution in environments with ambient light extremes.

EXTEGRA IP starlight 9000 FX has 720p50/60 resolution. EXTEGRA IP dynamic 9000 FX has

both 720p50/60 and 1080p25/30 resolution.

Options for powering the camera

Both aluminum and stainless steel models of EXTEGRA IP 9000 can be powered by the

following devices:

– 24 VAC 50/60Hz (VG4-A-PSU1, VG4-A-PSU2)

– 60 W midspan (NPD-6001A)

– 95 W midspan (NPD-9501A)

– VIDEOJET connect 7000 (VJC-7000-90)

When using 24 VAC to power the camera, customers have the option to install an Optical Fiber

Converter (OFC) Kit (sold separately). When using HPoE to power the camera, this option is

not supported.

Unpacking

–

This equipment should be unpacked and handled with care. Check the exterior of the

packaging for visible damage. If an item appears to have been damaged in shipment,

notify the shipper immediately.

– Verify that all the parts listed in the Parts List below are included. If any items are

missing, notify your Bosch Security Systems Sales or Customer Service Representative.

– Do not use this product if any component appears to be damaged. Please contact Bosch

Security Systems in the event of damaged goods.

– The original packing carton is the safest container in which to transport the unit and must

be used if returning the unit for service. Save it for possible future use.

2

2.1

EXTEGRA IP 9000 FX Product Description | en

11

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

Parts List

Parts Included with the Product

Quantity Item

1 EXTEGRA IP 9000 explosion-protected camera

1 Sunshield

4 M4 bolts, stainless steel, plus washers, for sunshield

1 1.5 mm hex key

1 Thread Adapter, ¾ in. NPT to M20, stainless steel

1 Multi-use tool

1 Installation Manual

User-supplied Parts

Quantity Item

3 M6 x 1.0 x 16 mm bolts with lock washers

1 Bottle of Jet-Lube® NCS-30 grease (as needed)

1 Tube of Molykote® BG 20 grease (as needed)

1 Tube of LA-CO Slic-Tite® Paste with PTFE (as needed)

2.2

2.2.1

2.2.2

12

en | Product Description EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Planning

Refer to the information below before installing the unit. This section provides dimensional

information and guidelines to help plan your installation.

Dimensional Drawings

135

5.30

102

4.01

125

4.93

Figure 3.1: Front view

Ø

6.6

0.26

71°

60.0

2.36

3/4-in.

NPT x4

Figure 3.2: Bottom view

3

3.1

EXTEGRA IP 9000 FX Planning | en

13

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

114

4.50

208

8.18

471

18.54

100

3.94

381

15.01

90°

Figure 3.3: Side view

Initial Preparations

The camera transmits zoom control commands and images over a TCP/IP network. It also

allows users to configure the camera display settings, camera operating settings, and to

configure the network parameters.

The camera incorporates a network video server in the IP module. The primary function of the

server is to encode video and control data for transmission over a TCP/IP network. With this

H.264 encoding, it is ideally suited for IP communication and for remote access to video

management systems. The use of existing networks means that integration with CCTV systems

or local networks can be achieved quickly and easily. Video images from a single camera can

be simultaneously received on several receivers.

– Determine the operating voltage at the installation site. The unit can receive an input

voltage range of 24 VAC ± 10%/HPoE without damage.

–

All units have been tested prior to shipment. It is advisable to check the unit’s operation

before installation.

!

Caution!

It is recommended that the installer wear an ESD strap or discharge any static electricity to

ground before handling any electronic components.

3.2

14

en | Planning EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Installation Overview

This chapter details the installation guidelines for the EXTEGRA IP 9000. It is important that

you consider these steps.

!

Warning!

Do not apply power to the unit in an explosive environment unless the housing is fully

installed, the front and back caps are tightened, and all openings are appropriately plugged

and sealed. Disconnect power before servicing or disassembling the unit.

Based on the explosion-protected requirements of the installation location, determine the

appropriate installation method and follow all local guidelines and laws. It is important to

keep the following in mind during installation:

– The back end cap of the unit must be removed for access to the internal electronics. The

set screws on the caps are tightened at the factory. It is easier to remove the end cap

with the sunshield removed.

– When tightening the end caps, ensure that the threads are clean and lubricated with Jet-

Lube® NCS-30 grease or equivalent.

– Before tightening the end caps, ensure that the o-rings are clean and lubricated with

Molykote® BG 20 grease (from Dow Corning) or equivalent.

–

Ensure that all 3/4-in. NPT plugs are securely tightened in the 3/4-in. NPT conduit

openings and sealed with LA-CO Slic-Tite® Paste with PTFE, apply per manufacturer’s

instructions on the label.

– Ensure that the unit is wired and sealed appropriately either with a conduit seal or a

gland and cable rated for the intended environment. Use LA-CO Slic-Tite® Paste with

PTFE thread sealant on all conduit or gland threads.

– Carefully follow all manufacturers’ instructions for applying grease and paste products.

– All cable entry devices shall be ATEX/IECEx-certified for Ex d IIB T6 Gb and Ex tb IIIC

T85°C Db, rated at least 85 °C (185 °F), suitable for the conditions of use and installed

correctly.

– All unused conduit openings shall be closed with the supplied conduit plug, which is a

3/4 in. NPT plug certified for Class I, Groups C and D; Class II, Groups E, F, and G; and

Class III; Class I, Zone 1, AEx d IIB T6; Ex d IIB T6 X, AEx tb IIIC T85°C Db, and Ex tb IIIC

T85°C Db X hazardous locations.

– The maximum surface temperature will not exceed 85°C when operated in the ambient

temperature ranges for the different power options (24VAC vs. HPoE) and housing

material as specified in the following table:

Aluminum

housing

Stainless steel

housing

NXF-9130-A4

NXF-9230-A4

NXF-9130-S4

NXF-9230-S4

Ambient operating range

when powered by 24 VAC

-50 °C to 60 °C

(-58 °F to 140 °F)

-50 °C to 55 °C

(-58 °F to 131 °F)

Ambient operating range when powered by

HPoE

-40 °C to 60 °C

(-40 °F to 140 °F)

-40 °C to 55 °C

(-40 °F to 131 °F)

– If starting up the unit below -40 °C, there may be a delay (up to 30 minutes) between

when power is applied to the camera and when video output is available.

4

EXTEGRA IP 9000 FX Installation Overview | en

15

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

– The joint between the junction box and housing is secured by a thread locker for

permanent securement. This joint shall not be removed because there may be damage to

the flame path threads.

– The device was subjected to the resistance to impact test at 2 J. It shall be installed

where it will not be subjected to impact.

– For ambient temperatures below –10 °C, use field wiring suitable for the minimum

ambient temperature.

Note: For instructions to configure the camera, refer to the Software Manual. Go to http://

www.boschsecurity.com

, navigate to the product page for your camera, and then locate the

document in the Documents tab.

16

en | Installation Overview EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Install the Optional Media Storage Card

The camera can accept a customer-supplied SDHC or SDXC memory card (hereafter referred

to as “SD card”) for local storage. (The camera will not accept MicroSD cards.) Using an SD

card is optional.

!

Caution!

Risk of electrostatic discharge!

Use proper CMOS/MOS-FET handling precautions and observe proper ESD safety precautions

(such as wearing grounded wrist straps) to avoid electrostatic discharge.

Note: Disconnect power to the camera while adding or removing an SD card.

Ideally, you should install the card before connecting cables and mounting the camera. To

install the card,

follow these steps

:

!

Warning!

DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT.

Note: You may need to remove the sunshield to remove the front end cap more easily.

1. Loosen the set screw on the front end cap using the supplied hex key.

2. Loosen the front end cap using the supplied multi-use tool. To prevent damage to the o-

ring, for every half turn counterclockwise turn back one quarter turn clockwise.

3. Unscrew the front end cap by hand.

Figure 5.1: Remove the front end cap

5

EXTEGRA IP 9000 FX Install the Optional Media Storage Card | en

17

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

Notice!

Take care not to drop the end caps to prevent damage to the cap threads.

4. Remove the inner mounting bracket assembly from the front of the housing:

Note: Before removing the assembly from the housing, ensure that all connections to the User

Interface Board have been removed.

– Using the multi-use tool, loosen the two (2) bolts that hold the assembly.

Figure 5.2: Loosen the 2 bolts

– Pull the assembly out of the housing until the card slot is accessible.

Figure 5.3: Pull the assembly out of the housing

5. Orient the card so that the side with the golden contacts faces away from the camera and

towards the housing as you hold the card in front of the card slot.

6. Slide the card into the card slot. Press the card until you hear a click and the card locks into

place.

18

en | Install the Optional Media Storage Card EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Figure 5.4: Card slot with SD card installed

7. Slide the assembly into the housing.

8. Tighten the 2 securing bolts to secure the assembly. Note: Do not overtighten the screws. If

you overtighten, you will deform the mounting bracket.

Figure 5.5: Tighten the 2 bolts

9. Clean and grease the O-ring and threads before replacing the front end cap.

10. Replace the front end cap.

11. Tighten the front end cap using the multi-use tool. Ensure that the O-ring is properly

seated. After tightening, ensure that there is no gap between the cap and the body of the

housing.

12. Tighten the set screws on the front end cap using the supplied hex key.

EXTEGRA IP 9000 FX Install the Optional Media Storage Card | en

19

Bosch Security Systems Installation Manual / Guide d'installation 2015.03 | 1.7 | F.01U.304.260

Connections

Power Cable Requirements

!

Warning!

Before proceeding, disconnect the power from the power supply cable. Ensure that the

voltage of the unit matches the voltage and type of the power supply being used.

Connect power from a 24 VAC class 2 power supply. Use AWG 16 to 22 stranded wire or AWG

16 to 26 solid wire; cut back 5 mm (0.2 in.) of insulation.

Cable size Stranded wire: AWG 16 to 22

Solid wire: AWG 16 to 26

Cable shape Round

Conductors 2-conductor version

Environmental Outdoor rated

!

Warning!

Bosch’s version of High PoE:

If supplying power to the camera by HPoE or a midspan device, you must install additional

surge protection.

The table below identifies the power devices that can be connected simultaneously to the

camera.

If power is supplied from: Camera can receive power simultaneously from:

60 W midspan (NPD-6001A)

24 VAC PSU

(VG4-A-PSU1, VG4-A-PSU2)

95 W midspan (

NPD-9501A)

VIDEOJET connect (VJC-7000-90)

Wire Distance Guide

This table lists the maximum wire distances for 16 and 18 AWG wires for 24 VAC power.

16 AWG

(1.5 mm)

18 AWG

(1.0 mm)

With OFC Kit 40 m (131 ft) 25 m (83 ft)

Without OFC Kit 42 m (136 ft)

26 m (86 ft)

Ethernet Cable Requirements

Cable Type Cat5e/Cat6e Ethernet (directly to the camera, or to a network switch

between the camera and the network)

Maximum Distance 100 m (330 ft)

Terminal

Connector

RJ45, Male

6

6.1

6.1.1

6.2

20

en | Connections EXTEGRA IP 9000 FX

2015.03 | 1.7 | F.01U.304.260 Installation Manual / Guide d'installation Bosch Security Systems

Page is loading ...

Bosch EXTEGRA IP 9000 FX NXF-9x30 Installation guide

Bosch EXTEGRA IP 9000 FX NXF-9x30 Installation guide

in other languages

Related papers

Other documents