Hatteland Technology Hatteland Display HT B22G Series User manual

Hatteland Display HT B22G Series
Hatteland Technology
Brand
Hatteland Technology
Model
Hatteland Display HT B22G Series
Category
Motherboards
Type
User manual

This manual is also suitable for

Hatteland Display AS, Eikeskogvegen 52, N-5570 Aksdal, Norway
Tel: (+47) 4814 2200 - mail@hatteland-display.com - www.hatteland-display.com
HT B22Gx STC-yzz-Mzzz
where “x” is CPU type, “y” = Operating System (OS) type, “z” = hardware configuration dependent
Compact Fanless Computer
USER MANUAL
User Manual
Updated: 12 Apr 2018 Doc Id: INB100610-2 (Rev 11)
Created: 363
Approved: 6987
Please visit www.hatteland-display.com for the latest electronic version of this manual.
Copyright © 2018 Hatteland Display AS
Eikeskogvegen 52, N-5570 Aksdal, Norway.
All rights are reserved by Hatteland Display AS. This information may not, in whole or in part, be
copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-
readable form without the prior written consent of Hatteland Display AS. Review also:
www.hatteland-display.com/pdf/misc/doc100703-1_permission_to_create_user_manuals.pdf
The products described, or referenced, herein are copyrighted to the respective owners.
The products may not be copied or duplicated in any way. This documentation contains proprietary
information that is not to be disclosed to persons outside the user’s company without prior written consent
of Hatteland Display AS.
The copyright notice appearing above is included to provide statutory protection in the event of
unauthorized or unintentional public disclosure.
All other product names or trademarks are properties of their respective owners !
WARNING: This is a class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
Statement above last revised 6 Jan 2015
3
IND100206-26
Contents
Contents .................................................................................... 3
Contents of package ...................................................................................5
General ...................................................................................... 7
About this manual ........................................................................................8
About Hatteland Display ..............................................................................8
www.hatteland-display.com .........................................................................8
Contact Information .....................................................................................8
Computers introduction ...............................................................................9
Product Labelling .......................................................................................10
Installation ............................................................................... 11
Installation and mounting of computers .....................................................12
Cables .......................................................................................................12
Housing / Terminal Block Connector Overview .........................................13
Accessible Storage Device (HDD/SSD) removal / replacement HT B22 ..15
Mounting Bracket Kit (Wall / Desktop) HT B22 ..........................................16
Mounting Guidelines and tips ....................................................................17
Physical Overview - HT B22Gx STC-yzz-Mzzz .........................................18
Front area of unit ................................................................................... 18
Connector area of unit ........................................................................... 19
Specications ......................................................................... 25
Specications - HT B22Gx STC-yzz-Mzzz ................................................26
Specications - CAN Module with CO-Processor .....................................27
ZIA0001310-B........................................................................................ 27
Specications - NMEA / IEC COM Module RS-422 / RS-485 ...................28
PCA100293-1 ........................................................................................ 28
Specications - Isolated Digital Input/Output Module ................................31
PCA100297-1 ........................................................................................ 31
Specications - LAN Module .....................................................................33
PCA100298-1 ........................................................................................ 33
Specications - Isolated COM Module RS-232 .........................................34
PCA100309-1 ........................................................................................ 34
Specications - External Modules (USB) ..................................................35
Contents
4
IND100206-26
Technical Drawings ................................................................ 37
Technical Drawings - HT B22Gx STC-yzz-Mzzz .......................................38
Technical Drawings - Accessories ........................................ 39
Technical Drawings - Mounting Bracket Kit - HT B22 ................................40
HT 00270 OPT-A1 ................................................................................. 40
Technical Drawings - Mounting Plate/Cable Tension Relievers ................42
for HT B22, HT B17, B18, B07, B08 ...................................................... 42
Technical Drawings - External Modules (USB) ..........................................43
Appendixes ............................................................................. 45
SSD Selection Guide .................................................................................46
Pinout Assignments ...................................................................................49
Trouble-shooting ........................................................................................53
Declaration of Conformity ..........................................................................54
Return Of Goods Information ....................................................................55
General Terms and Conditions ..................................................................56
API / VCOM Commands ..........................................................................57
Signal Detection Note ................................................................................62
Notes .........................................................................................................64
Revision History ........................................................................................66
5
IND100207-15
Item Description Illustration
TP52/TC01-1,8M
1 pcs of power cable European Type F “Schuko” to IEC.
Length 1.8m
EUR TYPE F
IEC
TP11/TC01-1,8M
1 pcs of power cable US Type B plug to IEC.
Length 1.8m
US TYPE B
IEC
MEDIA STD01
Documentation and Driver DVD for factory installed components like mainboard, IDE,
network etc. For most recent drivers, please visit “www.hatteland-display.com/archive”.
Note: To use this DVD disc you will need an external USB CD/DVD drive or provide means of
getting contents copied over via USB memory stick/network to the operating system. You can
alternatively download the drivers from our website www.hatteland-display.com
Menu browser for
Microsoft®
Windows®
Operating Systems
Test Reports papers:
1 pcs of Product Declaration
1 pcs of Computer Checklist
1 pcs of BurnInTest Certificate
HT 00270 OPT-A1
Mounting Bracket Kit suitable for Wall or Desktop mounting, consists of:
6 pcs M5x20mm Unbrako DIN912 Black
6 pcs M5 washer DIN125
6 pcs M5 Locking Nut DIN985
2 pcs Brackets
6 pcs M4x8mm CSK Torx DIN7984
Terminal Block Connector Kit
Terminal Block Connector Kit as follows (may in some cases be already factory mounted):
1 x 2-pin Terminal Block 5.08 (1961986) for DC Power In
4 x 5-pin Terminal Block 3.81 (1827732) for RS-422 / RS-485 NMEA COM I/O
Refer to “Conguring Housing / Terminal Block Connector” section for usage.
Contents of package
Package may also include: (based on accessories/options ordered)
Item Description Illustration
Terminal Block Connector Kit
Depending on factory mounted options, Terminal Bracket Connector kit as follows:
4 x 5-pin Terminal Block 3.81 (1827732) for RS-422 / RS-485 NMEA COM (PCA100293-1)
4 x 4-pin Terminal Block 3.81 (1792970000) for CAN Interface (ZIA0001310-B)
4 x 5-pin Terminal Block 3.81 (1827732) for Digital Input/Output (PCA100297-1)
HT 00228 OPT-A1
Kit contains:
1 x Mounting Plate with cable relief, RAL 9011.
4 x M4x8 (Torx DIN 965 Black Stainless Steel) screws
(additional screws are provided for similar computer models, please use M4x8 for HT B22).
HT 00300 MSOS IMAGE
Recovery/Restore Kit (1 x USB Memory Stick with original installation).
For reverting back to factory/customized Operating System installations.
For more information, visit http://www.hatteland-display.com/os
Note: Only applicable for factory delivered units with HDD/SSD hardware.
?
For computers that include 3rd party hardware; the package / accessories box may also include
additional CD / HW / Information from 3rd party supplier(s) depending on customized order.
Note: Entries listed below are for Standard factory shipments. Customized factory shipments may deviate from this list.
6
This page left intentionally blank
7
General
8
Hatteland Display AS
IND100077-1
General
About this manual
The manual contains electrical, mechanical and input/output signal specications. All specications in this manual,
due to manufacturing, new revisions and approvals, are subject to change without notice. However, the last update
and revision of this manual are shown both on the frontpage and also in the “Revision History” chapter at the end of
the manual. This User Manual is a standard/general manual that applies to all variations of its product family, i.e.
deviation from actual conguration may exist.
Furthermore, for third party datasheet and user manuals, please see dedicated Documentation and Driver DVD
delivered with the product or contact our sales/technical/helpdesk personnel for support.
About Hatteland Display
Hatteland Display is the leading technology provider of specialized display and computer products, delivering high
quality, unique and customized solutions to the international maritime, naval and industrial markets.
The company represents innovation and quality to the system integrators world wide. Effective quality assurance and
investment in sophisticated in-house manufacturing methods and facilities enable us to deliver Type Approved and Mil
tested products. Our customer oriented approach, technical knowledge and dedication to R&D, makes us a trusted
and preferred supplier of approved solutions, which are backed up by a strong service network.
www.hatteland-display.com
You will nd our website full of useful information to help you make an informed choice as to the right product for your
needs. You will nd detailed product descriptions and specications for the entire range on Displays, Computers and
Panel Computers, Military solutions as well as the range of supporting accessories. The site carries a wealth of
information regarding our product testing and approvals in addition to company contact information for our various
ofces around the world, the global service centers and the technical help desk, all ensuring the best possible
support wherever you, or your vessel, may be in the world.
Contact Information
Head ofce, Vats / Norway:
Hatteland Display AS
Eikeskogvegen 52
N-5570 Aksdal, Norway
Tel: +47 4814 2200
mail@hatteland-display.com
Sales ofce, Frankfurt / Germany:
Hatteland Display GmbH
Werner Heisenberg Strasse 12,
D-63263 Neu-Isenburg, Germany
Tel: +49 6102 370 954
Fax: +49 6102 370 968
Sales ofce, Oslo / Norway:
Strandveien 35
N-1366 Lysaker
Norway
Tel: +47 4814 2200
Sales ofce, Aix-en-Provence / France:
Hatteland Display SAS
Actimart- 1140, rue Ampère, CS 80544
13594 Aix-en-Provence, Cedex 3
France
Tel: +33 (0) 4 42 16 47 57
Fax: +33 (0) 4 42 16 47 00
Sales ofce, Vista / USA:
Hatteland Display Inc
380 South Melrose Drive,
Suite 349
Vista, CA 92081
USA
Tel: +1 760-643-4061
Fax: +1 858-408-1834
For an up-2-date list, please visit www.hatteland-display.com/locations
9
Computers
IND101057-2
General
Computers introduction
Hatteland Display’s range of type-approved computers is designed to perform in
harsh environments while providing the performance and flexibility you expect.
We offer rack mount and black box/standalone computer solutions for every
need. Our computers are used by system integrators, boat builders and end-
users and can be found on all vessel types, all over the world.
If you are looking for a high quality computer for navigation, monitoring or
entertainment solutions, Hatteland Display can fulfil your high expectations at a
reasonable cost.
Our computer range covers all eventualities and requirements. We offer a wide
range of processor choices, HDD/SSD and power options, and solid state
technology, neatly engineered within industry standard form factors such as 19”
rack mount, 2U and 4U solutions.
We continually develop our computers portfolio to make the best use of emerging
computer technology so you can be sure that your Hatteland Display computer
offers the power needed to run modern applications, with the flexibility to be
installed wherever you want, for any marine use.
Designed to perform in harsh environments...
10
IND100240-10
General
Product Labelling
Serial Number Label Layout
Serial Number Label Placement (external)
Label Size: 6cm x 2cm. Silver background with black text
Barcode “128” (TYP+SNO)
Compass Safe Distance info
Product Type
Input Voltages & Power Rating
Manufactured Date yyyymmdd
Manufacturer & Country
Quality Control (QC) OS S/N Serial Number
Quality Control (QC) Label
This label indicates that the unit is produced, tested and packed according to manufacturer’s QA
specications. It will include a Personal ID and signature by the personnell responsible for approving
the unit in production, test and warehouse departments. Label size is 3cm wide x 2.3cm high.
Operating System (OS) Serial Number Label
Only present if the unit was delivered with factory installed Operating System (OS) such as
Microsoft® Windows® Embedded Enterprise. Label size is 7cm wide x 2.8cm high.
Rear Side of unit
11
Installation
12Installation
IND100210-12
General Installation Recommendations
Installation and mounting of computers
1. Units may be intended for various methods of installation or mounting (rack mounting, panel mounting,
bracket mounting, ceiling/wall mounting); for details, please see the relevant mechanical drawings.
2. Adequate ventilation is a necessary prerequisite for the life of the unit. The air inlet and outlet openings must
denitely be kept clear; coverings which restrict ventilation are not permissible. The product might be without
any ventilation aperatures, in which the cooling chassis design will allow heat to dissipate properly away
from the unit instead. Make sure you allow space around for the heat to excess properly.
3. Exposure to direct sunlight can cause a considerable increase in the temperature of the unit, and might under
certain circumstances lead to overtemperature. This point should already be taken into consideration when
the bridge equipment is being planned (sun shades, distance from the windows, ventilation, etc.)
4. Space necessary for ventilation, for cable inlets, for the operating procedures and for maintenance, must be
provided.
5. To further improve the cooling of the unit we recommend installing Cooling Fans underneath blowing upwards
into the unit air inlet. This may be required in high temperature applications and also when there is reason to
expect temperature problems due to non-optimal way of mounting.
6. This Product shall be grounded to protective Earth. For AC Power cables this is done trough the ground wire
in the connector, for DC input the ground bolt shall be used. A shorter and thicker cable gives better
grounding. A 6mm² is recommended, but a 4mm² or even 2.5mm² can be used for this purpose
7. Expose to heavy vibration and acoustic noise might under certain circumstances affect functionality and
expected lifetime. This must be considered during system assembly and installation. Mounting position must
carefully be selected to avoid any exposure of amplied vibration.
General mounting instructions
1. The useful life of the components of all Electronics Units generally decreases with increasing ambient
temperature; it is therefore advisable to install such units in air-conditioned rooms. If there are no such
facilities, these rooms must at least be dry, adequately ventilated and kept at a suitable temperature in order
to prevent the formation of condensation inside the unit.
2. With most Electronic Units, cooling takes place via the surface of the casing. The cooling must not be
impaired by partial covering of the unit or by installation of the unit in a conned cabinet.
3. In the area of the wheel house, the distance of each electronics unit from the magnetic standard compass or
the magnetic steering compass must not be less than the permitted magnetic protection distance. This
distance is measured from the centre of the magnetic system of the compass to the nearest point on the
corresponding unit concerned. The exact distance is often mentioned in the specic product specications.
4. Transportation damage, even if apparently insignicant at rst glance, must immediately be examined and be
reported to the freight carrier. The moment of setting-to-work of the equipment is too late, not only for
reporting the damage but also for the supply of replacements.
5. The classication is only valid for approved mounting brackets provided by Hatteland Display. The unit shall
be mounted stand-alone without any devices or loose parts placed at or nearby the unit. Any other type of
mounting might require test and re-classication.
Cables
Use only high quality shielded signal cables. For RGB/DVI cables use only cables with separate coax for Red, Green
and Blue.
13
General Installation Recommendations
Installation
IND100210-14
Housing / Terminal Block Connector Overview
Housing / Terminal Block connectors are available in different sizes (example 2-pin, 4-pin, 5-pin) which plugs into the
connector area of the unit. They are mounted by factory default and delivered with the unit. The housing / terminal
block connectors have steering rails, which ensures that it can not be mounted wrong. The color of these connectors
may vary between black, green and orange depending on manufacturer. You may use approved equivalents of these
connectors, but note that warranty will be void if any damage would occur to either the unit’s original PCB terminal
socket connector or inside the unit (electronic components, boards etc.). The table below is applicable for any Series
X products, such as Display and Panel Computers, including newer type of Stand-Alone Computers.
Illustration Pins Manufacturer Details Connector used for module
5-pin MC 1,5/ 5-STF-3,81
Screwdriver: SZS 0,4X2,5mm
VDE, slot-headed.
Tightening torque min. 0.22 Nm.
Tightening torque max 0.25 Nm.
• RS-422 / RS-485 NMEA (PCA100293-1 / Q170 IO)
• Digital Input/Output (PCA100297-1 / Q170 IO)
Identi ed on Hatteland Display product data sheet as:
“Terminal Block 3.81”
└ Reference: http://catalog.phoenixcontact.net/phoenix/treeViewClick.do?reloadFrame=true&UID=1827732
2-pin MSTB 2,5/ 2-STF-5,08 BK
Screwdriver: SZS 0,6x3,5, slot-
headed.
Tightening torque min. 0.5 Nm.
Tightening torque max 0.6 Nm.
• DC Power IN (24VDC) - Single Input
Identi ed on Hatteland Display product data sheet as:
“Terminal Block 5.08”
└ Reference: http://catalog.phoenixcontact.net/phoenix/treeViewClick.do?reloadFrame=true&UID=1961986
4-pin BCZ 3.81/04/180F SN BK BX
Screwdriver: 0.4x2.5mm DIN 5264.
Tightening torque min.. 0.2 Nm.
Tightening torque max. 0.25 Nm.
• CAN Interface (ZIA0001310-B)
Identi ed on Hatteland Display product data sheet as:
“Terminal Block 3.81”
└ Reference: http://catalog.weidmueller.com/catalog/Start.do?localeId=en&ObjectID=1792970000
14
General Installation Recommendations
Installation
IND100210-14
If your installation require additional cable fasteners support, please visit and purchase directly from manufacturer:
Illustrations below are approximate, actual Housing and Hood may deviate slightly, but function remains the same.
Cable Housing - Illustration Cover Hood - Illustration
KGG-MSTB 2,5/ 2 (2-pin)
KGG-MC 1,5/ 5 (5-pin)
BCZ 3.81 AH04 BK BX (4-pin)
BCZ 3.81 AH05 BK BX (5-pin)
For 2-pin and 5-pin:
https://www.phoenixcontact.com/online/portal/us?uri=pxc-oc-itemdetail:pid=1803934&library=usen&pcck=P-11-02-01&tab=1
https://www.phoenixcontact.com/online/portal/us?uri=pxc-oc-itemdetail:pid=1834372&library=usen&pcck=P-11-02-01&tab=1
For 4-pin and 5-pin
http://catalog.weidmueller.com/procat/Product.jsp;jsessionid=B040D5EB6832629E567C884809FDF6C1?productId=(%5b1005290000%5d)
http://catalog.weidmueller.com/procat/Product.jsp;jsessionid=D399022A1B3211C0146BCBE716D93211?productId=(%5b1005300000%5d)
Conguring Housing / Terminal Block connectors
Below is a brief illustration that might be useful during conguration and installation of such connectors. You will need
suitable pre-congured cable(s) and tools to congure the connector(s) and cable(s) that are present in your
installation environment. Below is a sample procedure for a 2-pin DC power connector. The procedure is the same for
other connectors of this type as listed in table above. Unit used as illustration below is for reference only.
FIG 3
FIG 1
FIG 2
FIG 4
FIG 1: Unscrew (from top) or make sure that the screw terminal (square area) are fully open, so you can secure the
inserted cables correctly to the loose housing connector (it may already be plugged into the unit as per factory
installation).
FIG 2: Insert cables* (from front) and screw / secure the cables by turning the screw on top of the housing to secure
the cables properly. Check that the cables is rmly in place and do not appear loose or falls out when pulling gently.
*Note: Required polarization verication (for instance -/+ for DC power input) should conform with the markings on
the connector area of the unit. Ignoring the markings on the unit or its add-on modules might damage the unit and/or
external equipment in which end, warranty will be void.
FIG 3: Plug the housing into the appropriate connector area of the unit (glass should be facing down) and check again
that the cables secured conforms with the markings on the connector area of the unit. Finalize the installation by
fasten the screws located in front on each side of the housing connector (FIG 4).
15
IND100210-13
General Installation Recommendations
Installation
Accessible Storage Device (HDD/SSD) removal / replacement HT B22
Note: Areas of interest are marked in this section with symbols in RED color. Although the trays are Hot-Swappable,
it is considered to be a good practice to power off the unit and disconnect power cable before proceeding!
▼ 1: Locate which tray you want to remove/replace and press its eject button inwards (FIG1). The hatch will
automatically open due to spring lock/unlock design.
Note: The tray may be locked/unlocked already. If the hatch does not automatically open, you can unlock it by
using a Allen Wrench tool and turn anti-clockwise. Padlock symbols (FIG 2) indicate locked or unlocked position.
FIG 2
Locked
Unlocked
FIG 1
▼ 2: Pull out the casing gently as indicated.
The tray shown here has a SSD device already
in-place. Your tray may be empty depending on
system conguration.
▼ 3: Unscrew or screw 4 pcs x M3x4mm Phillips countersunk
screws as indicated. Replace or remove the device as needed.
Make sure the device connects with the interface connector
located in the end of the tray prior to fastening screws.
- Repeat the procedure backwards to nalize operation -
For added security and to prevent accidental removal of devices during computer operation, please consider
turning the Padlock clockwise to lock the tray once in place.
16
IND100210-13
General Installation Recommendations
Installation
Mounting Bracket Kit (Wall / Desktop) HT B22
Mounting Bracket Kit (HT 00270 OPT-A1) is included with delivery. Note: Areas of interest are marked in this section
with symbols in RED color.
Note: In order to secure the unit properly, please use only the screws delivered with the unit. Choosing own screws
and longer than M4x8 (brackets onto unit) may cause permanent damage inside the unit and Warranty will be void !
▼ 1: Prepare the brackets, one on each side of the
unit as indicated. Make sure the bracket is rotated
correctly by aligning as red line show below.
▼ 2: Mount each bracket onto lower part of unit, using
3 pcs M4x8 CSK Torx DIN7984 on each side of the unit. It is
suggested that you add Locktite 248 (3 drops or more) to the
screws prior to fastening.
▼ 3: Place the complete unit onto your desired
location (i.e. desktop/wall) and mark the positions
you need to drill. The drilling hole should be M5.
The space under the location should allow for M5
locking nuts. Max thickness of mounting area/
plate is 8mm. If your mounting area/plate is thicker,
please assure you acquire longer screws specied
as “M5x?? Unbrako DIN916 Black”, where “??” is
your required length. View below is TOP VIEW.
▼ 4: Finalize the mounting of complete unit onto your location
using 6 pcs M5x20 Unbrako DIN912 Black (#1) with 6 pcs M5
washer DIN125 (#2) and 6 pcs M5 Locking Nut DIN985 (#3)
at the bottom as illustrated. Veriy using hands to pull and
slide the unit to conrm it is secured tigthly onto location.
#1
#2
#3
17
IND100210-13
General Installation Recommendations
Installation
Mounting Guidelines and tips
Even though the HT B22 is fanless with no cooling apertures in the chassis, the unit will produce a certain amount of
heat through the aluminium chassis. The top of the chassis as been designed with heat dissipation groves which
allow heat to be properly expelled.
In order to ensure a stable operation and prevent over-heat of the unit, please respect the following illustrations and
guidelines given below based on various mounting positions by using the Mounting Bracket Kit (HT 00270 OPT-A1).
Keep in mind that heat always travels upwards and that heat in general has to be led away from chassis, even with
the use of external fan blowing directly at the chassis, if needed, making sure the air can circulate and slowly
decrease in temperature. It is impossible to predict every possible installation scenario in this document, so use tips
below during installation planning.
▼ Inside a cabinet, placed at with groves facing up
allowing heat to escape upwards. It is expected that
the cabinet has adequate aperatures in top to allow
accumulated heat to escape. It should be noted that
the size of the cabinet will impact how efcient the
cooling can become.
▼ Wall mounting. Make sure groves are aligned vertically as
indicated, allowing heat to escape upwards along with the
groves. Connectors can face upwards or downwards
depending on installation needs.
▼ Possible scenario for inside a cabinet, placed
at with groves facing downwards allowing heat to
not escape at all. Please install cooling fan to make
sure the air/heat can circulate and lead away from
the chassis. Although a fan might help, this type of
installation is not recommended as the entire
concept of heat dissipation is not respected.
▼ Possible scenario for Wall mounting. Heat does not
escape properly (gets stuck between horizontal groves).
Please install cooling fan to make sure the air is circulated
away from the chassis to allow adequate cooling, or choose
the option in the table above.
18
IND100133-52
Physical Overview - HT B22Gx STC-yzz-Mzzz
Power ON/OFF Button:
To turn ON the computer, press down button and release it immediately. The Power LED indication will illuminate blue
and the operating system will automatically boot. To turn OFF the computer, press down this button and hold it for 4
seconds. The operating system may require additionally tasks to be performed before computer shuts down and turns
off the unit.
Reset Button (Hard Reset):
To reset the computer in case of severe software failure, press this button. This reset button is a hard reset which
means the operating system will NOT be warned. Using this reset method may damage les and / or operating system
in worst case scenarios. Precaution should be taken when using this. To perform a safe software reset, press either
the power button, or use the operating system own reset functionality if possible.
Power LED:
While the unit is powered the Power LED will illuminate blue. When the unit is off the LED will also be off (not
illuminated).
2 x USB2.0 (<5m) INPUT / OUTPUT:
Supports any USB1.1 (12Mbps) and USB2.0 (480Mbps) compliant peripherals. Drivers for most USB devices are
usually included in operating system or on separate installation DVD’s delivered with Third Party products. USB 1.1
devices will operate in USB 1.1 mode (12 Mbps).
2.5” Removable SATA HDD/SSD Trays:
The unit can utilize 2 x HDD/SSD devices, 2.5” size. (1 x tray is by factory default occupied, Device #0). The
operating system and all other les will be placed on this, normally visible as drive C: The storage devices can be
easily be upgraded or replaced by pulling the HDD/SSD tray out. Both trays have their own HDD LED which will
illuminate blue when HDD is powered and/or reading/writing.
Front area of unit
Power ON/OFF
Reset Button
Power LED
2 x USB2.0 2.5” Removable SATA HDD/SSD Trays
Device #0 (Boot/Main)
Device #1 (Optional)
Power LED
Activity LED
Power LED
Activity LED
Physical Overview - HT B22Gx STC-yzz-Mzzz
19
IND100133-52
PS/2 Keyboard and PS/2 Mouse INPUTS:
Connect the PS/2 keyboard cable to the PS/2 5P Purple Color ”KB” connector (female).
Connect the PS/2 mouse cable to the PS/2 5P Green Color ”MS” connector (female).
DVI-I or RGB / VGA OUT:
Enables a direct clone signal output from the computer. You may choose to use a DVI-I 29P cable directly or use a
DVI-I -> RGB adapter to use a RGB/VGA HD D-SUB 15P instead for this purpose. Connect the cable to the Connector
(female) and secure it to the hex spacers provided on the unit. Connect the other end to your equipment and secure it.
To learn more about Single Mode and Clone Mode connectivity, functionality and behaviour of signal detection, please
review “Notes” section in this manual.
VGA / RGB OUT:
Will output a clone signal from the computer for use with external display or monitor. Connects via a High Density
D-SUB 15P Female connector. Fasten the cable to the connector using the provided screws on the cable housing
itself.
COM1 Serial Port INPUT / OUTPUT:
1 x D-SUB 9P Male connector with RS-232 support. Fasten the cable to the connector using the provided screws on
the cable housing itself. Baud Rate Min: 50b/s, Max: 115200b/s (120Kb/s, suggested to use shorter cables),
Non-isolated port. Wake on ring is not supported and no ESD protection. Third-Party Technical Chip Driver Details:
http://www.st.com/web/en/resource/technical/document/datasheet/CD00001609.pdf
Connector area of unit
PS/2 Keyboard In
1 x USB1.1
PS/2 Mouse In
DVI-I/RGB Out
Expansion area for optional modules
RGB/VGA Out
RS-422/RS-485 (COM2)
RS-232 (COM1)
2 x RJ45 Network
4 x RS-422/RS-485 NMEA / ECDIS (Default from Factory)
or Expansion area for optional modules.
Mic-in, Line-out
Power Input DC
Power Input AC
3 x USB2.0
For detailed pinout assignments and connector information, please review “Pinout Assignments” and
“Housing / Terminal Block Connector Overview” in this manual.
Grounding Screw
Physical Overview - HT B22Gx STC-yzz-Mzzz
20
IND100133-52
COM2 Serial Port INPUT / OUTPUT:
1 x D-SUB 9P Male connector with RS-422/RS-485 support. Fasten the cable to the connector using the
provided screws on the cable housing itself. Baud Rate Min: 50b/s, Max: 1497600b/s (1.5Mb/s), Non-isolated port.
Enhanced internal ESD Specications: +/-15kV Human Body Model, +/-15kV IEC1000-4-2 Air Discharge,
+/-8kV I EC 1 000-4-2 Contact Discharge.
Communication modes: Communication mode is selected using Hatteland Display API (check Driver DVD and
review chapter: “HT B22 - API / VCOM Commands” in this manual for more information.
Port is connected as a 0-modem cable: DCD, DSR and DTR is connected together in port. RTS and CTS is
connected in port.
Master mode full duplex: Transmitter is always active (Using TX pins), Receiver is always active (Using RX pins),
RTS signal is ignored.
Slave mode half duplex:
If RTS is active then it will transmit data. If RTS is inactive then it will receive data. Echo is not supported. (You can not
receive your own transmitted data simultaneously). All communication occurs over RX pins.
Note: RX has logic to ensure that the computer detect stop bit if no logic are driving RX bus. (Open port or drivers are
disconnected). This ensures stable operation of the system.
1 x USB1.1 (<10m) and 3 x USB2.0 (<5m) INPUT / OUTPUT:
Supports USB compliant peripherals. Drivers for most USB devices are usually included in operating system or on
separate installation DVD’s delivered with Third Party products.
- Port 1 is by factory default locked to USB1.1 (<10m, 12Mbps) and the
1:1
symbol is indicated next to the connector.
Peripherals that require more or less than 12Mbps should not be connected to this port, as both driver and device
will fail to install and initalize correctly. Please re-connect your device into port 2,3,4 instead in these situations.
- Port 2,3,4 is USB2.0 (<5m, 480Mbps) compliant, including support for USB1.1 (<10m, 12Mbps) peripherals.
Network 1, 2 INPUT / OUTPUT:
Supports 10/100/1000Mbps Ethernet (LAN). Suitable for twisted pair cables CAT.5E. Make sure the network cable
connector ”clicks” into the RJ-45 connector.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Hatteland Technology Hatteland Display HT B22G Series User manual

Hatteland Display HT B22G Series
Hatteland Technology
Brand
Hatteland Technology
Model
Hatteland Display HT B22G Series
Category
Motherboards
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents