voda VST91 Storm Bath Spout User manual

Brand
voda
Model
VST91 Storm Bath Spout
Type
User manual

Voda VST91 Storm Bath Spout

The voda VST91 Storm Bath Spout is suitable for all plumbing pressures and temperatures up to 500kPa and 65 degrees Celsius. It can be installed in mains pressure, unequal low, and equal low systems. The spout has a male plumbing connection and an 80mm faceplate. It can be adjusted for final positioning by loosening the grub screw underneath the spout and aligning it. The spout should not be cleaned with acidic, caustic/alkaline, abrasive, or citric cleaners. A soft, damp cloth is recommended for cleaning. Mild soap solutions can also be used occasionally.

Voda VST91 Storm Bath Spout

The voda VST91 Storm Bath Spout is suitable for all plumbing pressures and temperatures up to 500kPa and 65 degrees Celsius. It can be installed in mains pressure, unequal low, and equal low systems. The spout has a male plumbing connection and an 80mm faceplate. It can be adjusted for final positioning by loosening the grub screw underneath the spout and aligning it. The spout should not be cleaned with acidic, caustic/alkaline, abrasive, or citric cleaners. A soft, damp cloth is recommended for cleaning. Mild soap solutions can also be used occasionally.

Voda Plumbingware (NZ) Ltd | Freephone: 0508 367 366 | 5 Hewlett Street, Port Whangarei 0110 | vodaplumbingware.co.nz
Congratulations on your purchase of this high quality product from Voda Plumbingware.
Please read the following before installation and retain (along with your receipt) for future reference.
TECHNICAL SPECIFICATIONS
Suitable for All Pressures
Minimum Pressure = 35kPa
Maximum operating Pressure = 500kPa* (As per NZ Building Code AS/NZ 3500.1)
Maximum operating Temperature = 65 deg. Celsius
For domestic use only.
CONFIGURATION
Mains Pressure systems Install as supplied.
Unequal Low systems Install as supplied.
Equal Low systems Install as supplied.
INSTALLATION
*FOR PRESSURES EXCEEDING 500kPa INSTALL A PRESSURE REDUCING VALVE. THOROUGHLY FLUSH ALL
PIPES TO ELIMINATE ANY REMAINING DIRT AND RESIDUE, AND INSTALL INLINE FILTERS. FAILURE TO DO SO
MAY VOID THE WARRANTY.
• Please note, this spout has a MALE PLUMBING CONNECTION. An appropriate FEMALE connection should be
installed within the wall with adequate allowance for screwing the spout on aer wall lining is fitted.
• Aer screwing spout into wall connection, the spout can be adjusted to final positioning by loosening small
grub screw underneath spout and aligning.
• Turn on the water supply.
• Check for leaks.
STORM
Bath Spout
VST91
80mm Faceplate
15mm Male Plumbing
connection
Loosen grub screw underneath
spout to realign spout once
tightened into place.
Voda Plumbingware (NZ) Ltd | Freephone: 0508 367 366 | 5 Hewlett Street, Port Whangarei 0110 | vodaplumbingware.co.nz
ATTACH PROOF OF PURCHASE HERE
WARRANTY
PLEASE CALL US BEFORE REMOVING OR UNDERTAKING ANY REPAIR WORK.
Please refer to our website for warranty information: www.vodaplumbingware.co.nz/warranty
In the unlikely event that this product fails during its warranty period, phone our Customer Service team
immediately on 0508 367 366 – as unauthorised removal of the product may void the warranty.
CARE AND MAINTENANCE
SHOULD NOT BE CLEANED WITH ACIDIC, CAUSTIC/ALKALINE, ABRASIVE OR CITRIC CLEANERS.
A so, damp cloth is recommended for cleaning (Not a Micro fibre cloth). Mild soap solutions can also be used on
occasion.
=
PROUD PARTNER AND SUPPORTER OF MASTER PLUMBERS, GASFITTERS AND DRAINLAYERS
  • Page 1 1
  • Page 2 2

voda VST91 Storm Bath Spout User manual

Brand
voda
Model
VST91 Storm Bath Spout
Type
User manual

Voda VST91 Storm Bath Spout

The voda VST91 Storm Bath Spout is suitable for all plumbing pressures and temperatures up to 500kPa and 65 degrees Celsius. It can be installed in mains pressure, unequal low, and equal low systems. The spout has a male plumbing connection and an 80mm faceplate. It can be adjusted for final positioning by loosening the grub screw underneath the spout and aligning it. The spout should not be cleaned with acidic, caustic/alkaline, abrasive, or citric cleaners. A soft, damp cloth is recommended for cleaning. Mild soap solutions can also be used occasionally.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents