Astria Fireplaces WRT4826 Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
WRT4826
Category
Fireplaces
Type
Instruction Sheet
1
REPLACEMENT BLOWER KIT
FOR FORCED AIR KIT
P/N 506019-76
Rev. E, 12/2013
HEARTH PRODUCTS
KITS AND ACCESSORIES
KIT CONTENTS
1 ea. Blower Assembly
1 ea. Instruction Sheet
INSTALLATION INSTRUCTIONS FOR INSTALLING A REPLACEMENT FORCED AIR BLOWER KIT
FOR USE WITH WOOD-BURNING FIREPLACES LISTED IN TABLE 1
BLOWER FOR FORCED AIR KIT
Cat. No. Where Used
BISZY
Brentwood™ LV, Brentwood SP, Ladera™, Villa Vista™,
Montecito™, Montecito Estate™, WRT4820WS, WCT4820WS,
WRT3820WS, WCT6820WS, WCT6840WS, WRT4826WH, BIS®
Ultima CF, BIS Ultima-1, BIS Nova, BIS Panorama, BIS Tradition CE
and BIS Tradition
Table 1
GENERAL INFORMATION
This blower kit is used with the forced air system which provides distribu-
tion of warm air to another room or to a central heating system.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact your local distributor
or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
F79 REV. 5 12/2013
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 1 - Electrical Connection
Blower
Thermostat
Rheostat
Thermostatic
Activator
Junction Box
Rating: 120 Volts AC,
60 Hz, 1.5 Amp.
Ground
120 V AC
THE FIREPLACE MUST BE ELECTRICALLY CONNECTED AND
GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE
ABSENCE OF LOCAL CODES, WITH THE CURRENT CSA C22.1
CANADIAN ELECTRICAL CODE. FOR U.S.A. INSTALLATIONS,
FOLLOW LOCAL CODES AND THE NATIONAL ELECTRICAL CODE
ANSI/NFPA 70.
INSTALLATION
Step 1. Choose the proper location to install the blower. Put it in place
and secure it with four (4) self-drilling screws or 1/4” diameter
bolts.
Step 2. Install the blower thermostat in that part of the house to be heated
by the hot air duct. Do not install the blower thermostat in the
room where the fireplace is located.
Step 3. Install the thermostatic fan activator (VTU) under the firebox.
Note: There is a pre installed bracket under the right side of the
firebox.
Step 4. Proceed to electrical hook-up as shown in Figure 1, making sure
to ground the junction box.
CAUTION: This blower does not need regular maintenance,
however, if periodic cleaning is required, the power supply
must be disconnected.
Printed in U.S.A. © 2011 IHP LLC
P/N 506019-76 Rev. E 12/2013
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor
for fireplace code information.
Innovative Hearth Products
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
  • Page 1 1

Astria Fireplaces WRT4826 Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
WRT4826
Category
Fireplaces
Type
Instruction Sheet
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents