Astria Fireplaces Brentwood Instruction Sheet

Brand: Astria Fireplaces

Model: Brentwood

Category: Fireplaces

Type: Instruction Sheet

REPLACEMENT BLOWER KIT

FOR FORCED AIR KIT

P/N 506019-76

Rev. E, 12/2013

HEARTH PRODUCTS

KITS AND ACCESSORIES

KIT CONTENTS

1 ea. Blower Assembly

1 ea. Instruction Sheet

INSTALLATION INSTRUCTIONS FOR INSTALLING A REPLACEMENT FORCED AIR BLOWER KIT

FOR USE WITH WOOD-BURNING FIREPLACES LISTED IN TABLE 1

BLOWER FOR FORCED AIR KIT

Cat. No. Where Used

BISZY

Brentwood™ LV, Brentwood SP, Ladera™, Villa Vista™,

Montecito™, Montecito Estate™, WRT4820WS, WCT4820WS,

WRT3820WS, WCT6820WS, WCT6840WS, WRT4826WH, BIS®

Ultima CF, BIS Ultima-1, BIS Nova, BIS Panorama, BIS Tradition CE

and BIS Tradition

Table 1

GENERAL INFORMATION

This blower kit is used with the forced air system which provides distribu-

tion of warm air to another room or to a central heating system.

If you encounter any problems, need clariﬁcation of these instructions or

are not qualiﬁed to properly install this kit, contact your local distributor

or dealer.

Read this instruction sheet in its entirety before beginning the installation.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO

THESE INSTRUCTIONS.

SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL

BEFORE PROCEEDING.

F79 REV. 5 12/2013

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 1 - Electrical Connection

Blower

Thermostat

Rheostat

Thermostatic

Activator

Junction Box

Rating: 120 Volts AC,

60 Hz, 1.5 Amp.

Ground

120 V AC

THE FIREPLACE MUST BE ELECTRICALLY CONNECTED AND

GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE

ABSENCE OF LOCAL CODES, WITH THE CURRENT CSA C22.1

CANADIAN ELECTRICAL CODE. FOR U.S.A. INSTALLATIONS,

FOLLOW LOCAL CODES AND THE NATIONAL ELECTRICAL CODE

ANSI/NFPA 70.

INSTALLATION

Step 1. Choose the proper location to install the blower. Put it in place

and secure it with four (4) self-drilling screws or 1/4” diameter

bolts.

Step 2. Install the blower thermostat in that part of the house to be heated

by the hot air duct. Do not install the blower thermostat in the

room where the ﬁreplace is located.

Step 3. Install the thermostatic fan activator (VTU) under the ﬁrebox.

Note: There is a pre installed bracket under the right side of the

ﬁrebox.

Step 4. Proceed to electrical hook-up as shown in Figure 1, making sure

to ground the junction box.

CAUTION: This blower does not need regular maintenance,

however, if periodic cleaning is required, the power supply

must be disconnected.

P/N 506019-76 Rev. E 12/2013

IHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁcations, prices and also to discontinue colors, styles and products. Consult your local distributor

for ﬁreplace code information.

Innovative Hearth Products

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

Astria Fireplaces Brentwood Instruction Sheet

Brand: Astria Fireplaces

Model: Brentwood

Category: Fireplaces

Type: Instruction Sheet

Download PDF

report

Astria Fireplaces Brentwood Instruction Sheet

Astria Fireplaces Brentwood Instruction Sheet

Related papers

Other documents