Gigaphone 2420 User manual

1

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of fire, electric shock and injury to persons, including the

following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners

or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink,

or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product may

fall, causing serious damage to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation.

To protect it from overheating, these openings must not be blocked by placing

the product on the bed, sofa, rug, or other similar surface. This product should

never be placed near or over a radiator or heat register. This product should not

be placed in a built-in installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power supply to your

home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this product where

the cord will be abused by persons walking on it.

9. Never push objects of any kind into this product through cabinet slots as they

may touch dangerous voltage points or short out parts that could result in a risk

of fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take

it to an authorized service facility. Opening or removing cabinet parts other than

specified access doors may expose you to dangerous voltages or other risks.

Incorrect reassemb-ling can cause electric shock when the appliance is

subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the risk

of fire or electric shock.

Important Safety Instructions

2

12. Unplug this product from the wall outlet and refer servicing to an authorized service

facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions, because improper adjustment of other controls may result in

damage and will often require extensive work by an authorized technician

to restore the product to normal operation.

E. If the product has been dropped and the cabinet has been damaged.

F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lighting.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

3

The GIGAPHONE is an advanced cordless telephone that operates in the 2.4GHz

frequency range. Your GIGAPHONE is capable of supporting up to a maximum of

4 Handsets. Using additional Handsets, two extensions can be conferenced on a call,

while two other extensions can be talking internally, using the Intercom feature.

This manual is designed to familiarize you with the GIGAPHONE cordless telephone.

We strongly recommend you read the manual before using your phone.

To order additional systerm Handsets (model# 2420), battery packs

or headsets, call Vtech Communications Inc at 1-800-595-9511.

Introduction

4

Parts Check List

5. Battery Pack

6. Wall Mounting Bracket

7. Belt clip

8. Owner's Manual

To purchase replacement battery packs, call Vtech Communications Inc at 1-800-

595-9511. In Canada, call VTech Electronics Ltd at 1-800-267-7377.

1. Base Unit

2. Handset

3. AC Power Adapter

4. Telephone Cord

Telephone Line Cord

AC Power Adapter

Handset

Battery Pack

Base Unit

Wall Mounting Bracket

Belt Clip

Owner's Manual

OWNER'S MANUAL

5

The Handset Layout

1. Antenna

2. Earpiece

3. Headset Jack (2.5mm)

4. Scroll Keys

5. On (Flash)

6. Dialing Keys (0-9)

7. Handsfree Speakerphone

8. LCD Display

9. Select

10. Off (Clear)

11. Battery Compartment

12. Intercom

13. Microphone

1

2

3

4

5

6

7

8

9

10

13

11

12

6

The Base Unit Layout

AC Power Jack

Message Waiting

Indicator

Phone Cord Jack

Page Key

Charge Indicator

7

Setup

1. Plug the AC power adapter into an electrical outlet, and the DC connector

into the back of the base unit.

Connecting to phone line

Plug one end of the telephone line cord into the jack on the back of the base unit. Plug

the other end of this cord into the wall jack.

Checking for dial tone

After the battery is charged press ON on the Handset. The Phone icon will

appear on the handset display, and you will hear dial tone. If not, see In Case of Difficulty.

Tone/Pulse selection

The TONE/PULSE switch is located on the bottom of the Base Unit, next to the telephone

jack. It is factory set to TONE. If you have rotary (Pulse) service, set the switch to

PULSE.

CAUTION: Use only the 7 volt power adaptor provided with your GIGAPHONE.

Getting Started

To AC outlet

To telephone

jack

To telephone

socket outlet

AC adapter

IMPORTANT:

FOR MAXIMUM PERFORMANCE OF

YOUR CORDLESS TELEPHONE SYSTEM:

1. Choose a central location for your Base Unit.

2. Install your Base Unit and Extension Handsets

away from electronic equipment, such as personal

computers, television sets and microwave ovens.

3. In locations where there are multiple cordless

telephones, separate base units as much as possible.

4. Install your telephone equipment away from

heat sources and sunlight.

5. Avoid excessive moisture, dust or extreme cold.

8

Getting Started

Follow the steps below:

1. Remove the battery cover by

pressing on the indent and sliding

downward.

2. Place the new battery pack in the

handset with the metal contacts

aligned with the charge contacts in

the battery compartment.

3. Replace the battery cover by sliding

it upwards.

4. If the new battery pack is not already

charged, place the handset in the

base unit, or a remote charging

stand, and allow it to charge for 12

hours. After initial charge, a

maintenance charge of 8 hours

should be sufficient.

Installation of Battery Pack in Handset

The original Handset that is shipped with your GIGAPHONE system will be

automatically registered to the Base. This Handset is HANDSET 1.

As you register additional Handsets to the system, they will be assigned extension numbers

in the following order: HANDSET 2, HANDSET 3, and finally HANDSET 4.

Whenever a Handset battery pack is installed, the Handset will automatically begin

SEARCHING FOR BASE (if previously registered), or it will prompt you to ENTER

BASE ID to register the new Handset.

1

3

2

9

Charging Of Handset Battery Pack

The Handset of your GIGAPHONE cordless telephone is powered by a rechargeable

battery pack. It charges automatically whenever the Handset is in the Base Unit.

You should charge the battery pack for 12 hours when you first receive your phone.

You'll know the battery pack needs charging when:

• The low battery message is

displayed:

• The handset seems completely dead,

the LCD is completely clear and

does not activate when you press the

keys.

IMPORTANT:

1. Do not dispose of a battery pack in a fire, the cell may explode.

2. Do not open or mutilate the battery pack. Toxic substances may be released, causing

harm to eyes or skin.

3. Exercise care in handling battery packs in order to prevent an accidental short

of the charge contacts, potentially causing the battery pack to overheat.

4. Do not dispose of this battery pack into household garbage. Please refer to the

following information concerning proper battery recycling:

Getting Started

10

Getting Started

Wall Mounting

The Wall Mount bracket is designed for

use on standard Wall Mount plates only.

1. Line up the tabs on the wall mount

adapter with the holes on the bottom

of the base unit. Snap the wall

mount bracket firmly in place.

2. Plug the AC adapter into an electrical

outlet, and the DC connector to the

back of the base unit. If the handset

battery pack has not been charged

previously, place the handset in the

base unit cradle, and allow it to

charge for 12 hours.

3. Connect the telephone line cord to

the jack on the back of the base unit,

and the other end to the wall jack.

4. Mount the base unit on the wall.

Position the base unit so the

mounting studs will fit into the holes

on the wall mount bracket. Slide

base unit down on the mounting

studs until it locks into place.

2

3

1

11

Registration and Operation of the VT2420 Accessory Handset

Your GIGAPHONE system can operate up to 4 Handsets.

The accessory Handset consists of the following:

Setup Of The 2420 Accessory

Handset

1. Plug the AC power adapter into an

electrical outlet.

2. Remove the Handset battery cover

by pressing on the indent and sliding

downward.

3. Place the new battery pack in the

Handset, with the metal contacts

aligned with the charge contacts in

the battery compartment.

4. Replace the battery cover by sliding

it upward.

5. Place the Handset in the Charge

Cradle, and allow it to charge for 12

hours. After the initial charge, a

maintenance charge of 8 hours

should be sufficient.

Getting Started

Handset Battery Pack Charger Unit

Belt Clip

1

5

3

12

Enter Base ID Code

1. After charging the Handset, remove

it from its Charge Cradle, the screen

will display:

2. Press NEW, then enter the 15 digit

Base Unit ID code, located on the

underside of the Base Unit.

3. Press OK. The Handset will display:

PLEASE WAIT!!

4. Wait approximately 15 seconds.

The Handset will display:

FOUND BASE

If the Handset displays: BASE

BUSY TRY LATER, this indicates

that the system is in use. Wait until

the Base Unit is in the idle (on hook)

mode, and repeat steps 2 to 4.

NOTE: Occasionally, it may take longer

than 15 seconds for the Handset to confirm

registration to the Base Unit. This is

normal.

Congratulations! You can now enjoy the

benefits of your multi-Handset system.

Registration and Operation

Getting Started

13

Handset Icons

Icon Description

Line In Use indicator

On steady with no number next to it when a parallel set is in use.

On steady with one or more numbers next to it, indicating which

extensions are using the line. For example, 12 indicates that

Handset 1 and Handset 2 are on an outside call.

Intercom indicator

On steady with the extension numbers currently on an intercom call.

For example, 12 indicates that Handset 1 and Handset 2 are on

an intercom call.

Battery indicator

Cycles (Low, Medium, and High) when Handset battery is charging.

Flashes when a low battery condition is detected.

Mute indicator

On steady when the Handset microphone is muted.

Hold indicator

On steady when the line is on hold.

Handset Registration indicator

FF is displayed when a Handset is either not registered, or is

searching for a Base unit.

M

H

R

Handset and Base Indicators

Basic Operation

14

Handset LEDs

LED

Message

Waiting

Base LEDS

LED

Message

Waiting

Charging

Description

• Lights to indicate that you have new messages in your voicemail.

Service must be subscribed to through your local telephone

company.

Description

• Flashes to indicate that you have new messages in your voicemail.

Service must be subscribed to through your local telephone

company

•Lights whenever the handset is placed in the base unit charging

cradle.

Handset and Base Indicators

Basic Operation

15

The GIGAPHONE has an advanced design

that uses a menu structure and soft keys

to access all of the built-in features.

Example of the idle mode display:

RDL (Redial)

Soft Menu Functions

Press RDL to display the last 5 telephone numbers dialed. The number on the top line

is the most recent number dialed.

• Use the scroll keys to select the desired the number.

• To dial the number, you can simply press the ON or HANDSFREE key.

• To erase (or save) the number, select this option to delete (or save) it.

MENU

With the Handset in the idle (OFF) mode, press the MENU key to access the following

options:

•CALLS LOG (CALLER ID)

• HANDSET SETTINGS

• RANGE EXTENDER

• REGISTER

Use the scroll keys to select the desired option, then press OK.

Basic Operation

16

Basic Operation

From the idle (OFF) mode, press MENU,

use the scroll keys to select CALLS

LOG, then press OK. The Caller ID

information of the most recently received

call will be displayed. For example:

To scroll to other records, use the aaaaaa

scroll keys.

To dial the number displayed, you can

simply press the ON or HANDSFREE

key.

You can also press the CID key to access

the following options ( DEL, OPT#,

SAVE):

DEL : Select this option to delete

Calls Log (Caller ID)

THIS or ALL records in Caller ID memory.

OPT# : Select this option to display up to four possible dialing strings of the number

stored in Caller ID memory. If a number is provided in the Caller ID data,

the possible options to choose from will be either 7, 8, 10, or 11 digits. For

example, if the original number in Caller ID menory was 808-880-8808, then

the display options will be:

Use the UP and DOWN keys

to make selection, and then

press DIAL, ON or

HANDSFREE to dial the

number.

SAVE Select this option to save the displayed Caller ID record into Speed Dial

Memory. Only Caller ID records with telephone numbers can be saved into

Speed Dial Memory. If you need to modify the number after saving, see

TO EDIT A NUMBER.

Caller ID - Call Waiting ID

Your GIGAPHONE is capable of displaying the name and/or number of the party calling

before you answer the phone (Caller ID). It is also capable of displaying Caller ID

information in conjunction with a Call Waiting alert signal (Call Waiting Caller ID).

With Call Waiting Caller ID, the Caller ID data is displayed so you can decide whether

to answer the incoming call, or continue with your current conversation.

NOTES ABOUT CALLER ID & CALL WAITING CALLER ID

These are subscription services, provided by most regional telephone service

providers. You must subscribe to these services to get the benefits of these features.

If you do not subscribe to Caller ID services, you can still use your GIGAPHONE

and the other features it offers.

Due to regional incompatibilities, Caller ID information may not be available for

every call you receive. In addition, the calling party may intentionally block their

name and phone number from being sent.

17

Handset Settings

Basic Operation

From the Handset Settings menu, you can select the following options:

• RINGER VOLUME

Select this option to adjust the ringer volume. Use the scroll keys to

adjust the volume up or down. A Handset will display a graphic indicator of the

selected volume setting. Press OK to confirm your selection and return to the

Handset Settings menu.

• RINGER MELODY

Select this option to adjust the ringer melody or tone. Use the scroll

keys to select from the six available tones. Press OK to confirm your selection

and return to the Handset Settings menu.

• LOW BATT TONE

Select this option to turn the Low Battery warning tone ON or OFF. Press the

OFF or ON soft keys, to make your selection. Press OK to confirm your selection

and return to the Handset Settings menu. When set to ON, the Handset will emit

a warning tone when a Low Battery condition is detected.

• RANGE TONE

Select this option to turn the Out of Range warning tone ON or OFF. Press the

OFF or ON soft keys, to make your selection. Press OK to confirm your selection

and return to the Handset Settings menu. When set to ON, the Handset will emit

a warning tone whenever the Handset is taken out of range of the Base.

• KEYPAD TONE

Select this option to turn the Keypad tones ON or OFF. Press the OFF or ON

soft keys, to make your selection. Press OK to confirm your selection and return

to the Handset Settings menu. When set to ON, the Handset will emit a beep

whenever a key is pressed.

• CONTRAST

Select this option to adjust the contrast level of the Handset display. Use the

scroll keys to make your selection. The handset display will automatically

adjust as you make your selection. Press OK to confirm your selection and return

to the Handset Settings menu.

• LANGUAGE

Select this option to change the display from English to Spanish. Use the

scroll keys to select language, then press OK to confirm your choice.

18

Range Extender

Your GIGAPHONE has an enhanced feature that is designed to improve performance.

If you are using your GIGAPHONE in an area with excessive interference, or you require

a moderate increase in operating range. the Range Extender feature can help to improve

both the sound quality and range. Actual range will depend on your environment.

To select the Range Extender setting, follow the procedure listed below:

CALLS LOG

HANDSET SETTINGS

RANGE EXTENDER

REGISTER

Note : When Range Extender mode is enabled, your GIGAPHONE will consume more

battery power. That means the standby and talk time of your Handset will be shorter.

• In the idle(OFF) mode, press MENU

and use the scroll keys to select

RANGE EXTENDER, then press

OK.

• There are 3 option settings in the

RANGE EXTENDER menu:

1. Select OFF to disable RANGE

EXTENDER

2. Select ON to enable RANGE

EXTENDER. An "E" icon will

appear in the upper left corner

of the Handset display,

indicating that RANGE

EXTENDER is ON.

3. Select AUTO to allow your GIGAPHONE to automatically monitor the signal

strength between the handset and base unit, and activate whenever necessary.

With this option selected, your GIGAPHONE may occassionally enable or

disable the RANGE EXTENDER feature. When RANGE EXTENDER is

enabled, an "E" icon will appear in the upper left corner of the Handset display.

• Use the scroll keys to select the desired setting, and then press OK to confirm

the selection.

Register

Basic Operation

*

Use this option to register a Handset to the GIGAPHONE Base. You can register a

total of four Handsets to the GIGAPHONE Base. This process is activated automatically

whenever a new handset is powered up in range of the GIGAPHONE Base.

You will be prompted to enter the 15-digit Base ID code printed on the underside of

the base unit. After entering this code, press OK. The Handset will display SEARCHING

FOR BASE, and then FOUND BASE when the process is complete.

Note : Base ID codes are 15 digits long and can include the following characters :

0, 1,

2, 3, 4, 5, 6, 7, 8, 9, , or # .

19

The GIGAPHONE can store up to 50 names/numbers in memory. Each memory location

can hold up to 32 digits and up to 16 characters for the name.

When prompted to ENTER NAME?, use the digit keys to 'spell' the name. Each press

of a particular key causes characters to be displayed in the following order:

MEM (Memory)

Basic Operation

Number Key

1

2

3

4

5

6

7

8

9

0

#

Characters (in order)

& ' , . 1

A B C a b c 2

D E F d e f 3

G H I g h i4

J K L j k l 5

M N O m n o 6

P Q R S p q r s 7

T U V t u v 8

W X Y Z w x y z 9

0

#

*

20

Basic Operation

To Store a Number/Name:

• Starting from the idle screen, enter

the number you want to store in

memory.

• Be sure to include long distance

codes and pauses (using the PAUSE

softkey) if necessary. Press the

MEM softkey.

• You will then be prompted to

ENTER NAME? Use the digit

keys to 'spell' the name. If you make

a mistake, press the CLR softkey.

To enter a space press aa . When

finished, press SAVE.

• If there is space available in memory,

the number/name will be saved and

the Handset will return to idle mode.

• If the memory is full the Handset

will display PHONEBOOK IS

FULL and exit to the idle screen

without saving the entry.

MEM (Memory)

Page is loading ...

Gigaphone 2420 User manual

Gigaphone 2420 User manual

Related papers

Other documents