2. Computers & electronics
  3. Networking
  4. Network switches
  5. BAS-IP
  6. EVRC-IP

BAS-IP EVRC-IP, bas IP EVRC-IP Lift Controller User manual

  • Hello! I've reviewed the user manual for the bas IP EVRC-IP lift controller, and I'm ready to assist you with any questions you have. The manual details the controller's features, such as its PoE power option, support for up to 16 floors, Ethernet connectivity and fire alarm contact connection, along with instructions for installation and use.
  • What is the maximum number of modules per system?
    What type of cable is recommended for connection?
    How many floors can be managed using single controller?
USER MANUAL
LIFT СONTROLLER
EVRC-IP
EVRC-IP
LIFT СONTROLLER
The controller is designed to be integrated into the lift system by connecting
EVRC-IP dry contacts to the lift controller contacts across floors.
to the lift car when calling from the call panel or when presenting
The module has support for PoE power and allows you to organize access
be connected to one controller.
a contactless card.
Up to 16 floors with normally open or normally closed contact types can
of which gives different access rights to use the lift.
The module has Ethernet interaction interface. On this interface, the module
receives information about the raised card or the entered code, on the basis
You can also connect fire alarm contacts to the controller to lock the lift
in case of fire.
Full User Manual
Device description
wiki.bas-ip.com
POW / NET
24V
GND
FIMS
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
24V
GND
485A-1
485B-1
485A-2
485B-2
RJ45 PoE
485
B10
B11
B12
B13
B14
B15
B16
POW
B02
B03
B04
B05
B06
B07
B08
B09
B01
Appearance
Specifications
Rated voltage: POE support.
Rated power: 7 W.
Standby power: 1 W.
Working temperature: -40 — +75° C.
Storage relative humidity: 20% - 93%.
IP Degree: IP30.
Max number of modules per system: 98.
EAN: 5060514912478
Completness check of the product
Before installing the controller, be sure to check that it is complete and all
components are available.
The controller kit includes:
Controller
Manual
1 pc
1 pc
After verifying the device's completeness, you can switch to the controller
connection.
To connect controller you will need:
Electrical connection
An Ethernet UTP CAT5 or higher cable connected to a PoE switch or
to a normal switch/router.
Cable length recommendations
The maximum length of the UTP CAT5 cable segment shouldnot exceed 100 meters,
according to the IEEE 802.3 standard.
Power supply at +24 Volts DC if there isn't PoE.
The connection scheme of all components
To connect the relay contacts
of each floor you need to use
the contacts NO and COM.
On the main board, near each
port there is a three- pin
connector. If you want the relay
to be in the position N.C. after
turning off the power, connect
terminals 1 and 2. If you want
the relay to be in the N.O. after
power on, connect terminals
3 and 2.
24V
GND
FIMS
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
B1
B2
B3
B4
12V
GND
485A-1
485B-1
485A-2
485B-2
NO
NC
COM
NO
NC
COM
RJ45
B10
B11
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
B5
B6
B7
B8
B9
NO
NC
COM
NO
NC
COM
NO
NC
COM
NO
NC
COM
NO
NC
COM
B12
B13
B14
B15
B16
PoE
485
POW
Connection and searching the device
Ethernet UTP Cat 5e 2-wire cable Power cord
Power Supply
SH-20.16
AM-02
Manager PC
MAIN IN POWER LAN1 LAN2 MAIN OUT
Link/Act
CHANNEL1 CHANNEL2 CHANNEL3CHANNEL4 CHANNEL5CHANNEL6CHANNEL7 CHANNEL8
PoE
PoE Switch
1 2 3 4 LINK PWR PWRLINK
UP LINK UP LINKLINK PoE
LAN
2Wire
Power
AA-14FB
UPS DP/S
SH-20.4
SW-10
SW-02
Lock
AT-07L
PoE
PoE Switch
1 2 3 4 LINK PWR PWRLINK
UP LINK UP LINKLINK PoE
SH-20.4
AT-07L
PoE
PoE Switch
1 2 3 4 LINK PWR PWRLINK
UP LINK UP LINKLINK PoE
SH-20.4
Connect the controller to the power supply through a PoE switch, either
from a 24-volt power supply and to your local area network. After that, run
the program Remote Upgrade tool.
(the controller has the letter E in its ID, which makes it easy to find it in the list
of devices):
In the list of devices, find the controller as shown in the picture below
By default, the controller has an IP address of 192.168.68.90.
EVRC-IP
EVRC-IP
EVRC-IP
EVRC-IP
Power Supply Power Supply Power Supply Power Supply Power Supply
Warranty
The warranty card number
Model name
Serial number
Seller name
With following stated terms of warranty is familiar, functional test was
performed in my presence:
Customer signature
Warranty conditions
The warranty period of the product — 36 (thirty-six) months from
the date of sale.
Transportation of product must be in its original packaging or supplied one
by the seller.
The product is accepted in warranty repair only with a properly filled warranty
card and the presence of intact stickers or labels.
The product is accepted for examination in accordance with the cases
provided by law, only in the original packaging, in a full complete set,
appearance corresponding to the new equipment and presence of all relevant
properly filled documents.
This warranty is in addition to the constitutional and other consumer rights
and in no way restrict them.
Terms of warranty
The warranty card must indicate the name of the model, serial number,
purchase date, name of the seller, seller company stamp and
the customer’s signature.
Delivery to the warranty repair is carried out by the buyer himself.
Warranty repairs carried out only during the warranty period specified
in the warranty card.
The service center is committed to do everything possible to carry out
the repair warranty products, up to 24 working days. The period spent
on the restoration of product functionality is added to the warranty period.
EAN: 5060514912478
Notes
Notes
EAN: 5060514912478
www.bas-ip.com
/