CTA PARAF2 Owner's manual

CTA
Brand
CTA
Model
PARAF2
Type
Owner's manual
Customizable Premium Locking Floor Stand Kiosk
with Graphic Card Slot for Branding
PAD-PARAF1/ PAD-PARAF1W
INSTRUCTION - MANUAL
888-733-4448
CONTENTS: 1. INSTALLING BASE:
ALIGN BASE PLATE(A) WITH THE BODY(B) AND
ROTATE IN SCREWS (G) IN FROM THE BOTTOM USING THE PROVIDED
ALLEN KEY TOOL(D) AND RELATED HARDWARE NEEDED.
2. SETTING UP GRAPHIC CARD SLOT
SLIDE OUT THE (2) GRAPHIC CARD PANELS IN THE FRONT AND BACK OF THE BODY (B). IF THERE IS A STICKER FILM, REMOVE
THAT FIRST. IF YOU HAVE PRINTED OUT A STICKER GRAPHIC, PLACE IT ONTO THE PANEL. IF YOU ARE USING A COMPLETE NEW
PANEL, YOU CAN REPLACE THE INITIAL PANELS THAT CAME WITH THE FLOOR STAND. PLACE ONE PANEL BACK FIRST.
AB
C
DE
GH
M6 x 18
M6 Allen Key
F
M5 Allen Key
M5 x 12
M5 Nut
B
A
G
D
B
Foam Adapter &
Sheet Bundle
I
J
x8
K
x4
M6 Washer
LM
Anchors Base Hole Filler
x2 x2
N
3. SETTING UP CABLE ROUTING
WITH ONLY (1) PANEL BACK IN, SLIDE IN THE POWER CORDS AND ANY OTHER CORDS THAT WOULD
NEED TO BE CONNECTED TO THE TABLET THROUGH THE BODY AS SHOWN. THERE WILL BE GAPS AT
THE TOP AND BOTTOM FOR THEM TO ROUTE OUT TO THE POWER SOURCE AND TO THE DEVICE. SLIDE
IN SECOND PANEL WHEN ROUTING IS FINISHED.
4. ATTACH VESA PLATE
ATTACH VESA PLATE AT TOP (N). ROUTE ANY WIRES
THROUGH THE PLATE’S OPENINGS. ALIGN SCREWS
(H) AND WASHERS (K) WITH SCREW HOLES AND
ROTATE IN USING ALLEN KEY (F) UNTIL SECURELY
TIGHTENED.
888-733-4448
5. ATTACHING THE
TABLET ENCLOSURE
UNLOCK AND OPEN TABLET ENCLOSURE,
ATTACH SCREWS AND HEX BOLTS AS SHOWN
THROUGH THE BACK OF THE ENCLOSURE
TO COMPLETE SETUP.
6. SETTING UP
ENCLOSURE & TABLET
6A - UNLOCK THE TABLET ENCLOSURE (C)
BY ROTATING THE KEY (J) UNTIL IT POPS
OPEN
6B - FIND THE APPROPRIATE SIZE INCLUDED
FOAM PADDING (I) FOR THE TABLET YOU WISH
TO USE. MAKE SURE DEVICE IS COMPATIBLE
FOR THE ENCLOSURE
6C - LAY YOUR DEVICE IN AND CONNECT ANY
CABLES OR CORDS YOU HAVE
6D - IF NEEDED, MAKE SURE TO LAY-IN THE
CORRECT MASKING COVER (I). THEN CLOSE AND
LOCK THE ENCLOSURE AND YOU’RE READY TO GO.
N
B
H
FK
(OPTIONAL) ANCHORING
DOWN FLOOR STAND TO
FLOOR
H
E
M5 x 12
x4 C
L
x2
M
x2
I
J
I
USE A POWER DRILL (NOT
INCLUDED) TO CREATE A
CAVITY IN THE FLOOR. INSERT
THE BOTTOM PORTION OF
THE ANCHOR (L). SCREW IN
TOP PORTION (L) WITH
SCREWDRIVER (NOT
INCLUDED) UNTIL SECURELY
TIGHTENED.
IF NOT ANCHORING FLOOR
STAND INTO FLOOR, INSERT
FILLERS (M) TO FILL IN HOLES
FOR A SEAMLESS AESTHETIC
ON THE BASE
  • Page 1 1
  • Page 2 2

CTA PARAF2 Owner's manual

CTA
Brand
CTA
Model
PARAF2
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents