American Standard 2908.018WC User manual

Type
User manual

This manual is also suitable for

REMINISCENCE™ DROP-IN
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
REMINISCENCE DROP-IN WHIRLPOOL &
BATHING POOL
2908.018W Whirlpool featuring System I
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Sculptured rim design w/raised headrest
Dual, molded-in arm rests
• Faucet deck/accessory area at drain end
1.5 HP single speed, self-draining pump/motor
• Factory installed power cord with plug
Eight multi-directional and flow-adjustable jets
including:
- Two Ideal-flow jets at foot area
- Four body massage jets
- Two recessed back-rest jets
Deck-mounted, air switch On/Off
Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
Factory installed and tested whirlpool system
2908.018WC StayClean™ Whirlpool
Massage featuring System I
• Same as 2908.018W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
2908.028W Whirlpool featuring System II
Same as 2908.018W except:
2.0 HP, two speed, self-draining pump/motor
with pulse feature
Deck-mounted electronic control with 20
minute built-in timed safety shut off and
Chrome bezel
2908.028WC StayClean™ Whirlpool
Massage featuring System II
• Same as 2908.028W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
2908.002 Bathing Pool only
Nominal Dimensions: 66” x 36” x 24-1/4"
(1676 x 914 x 616mm)
© 2005 American Standard Inc.
BV-5
To Be Specified - Required:
Color:
Bath Faucet (Specify finish)
Bath Drain: 1583.470 (Specify finish)
To Be Specified - Optional:
Safe-T-Heater*: 9075.120
Jet Trim Ring Kit: 9860.200-two per kit (Specify finish)
for Body Massage Jets only
System II Control Bezel: 9861.100 (Specify finish)
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Rev. 10/05
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
For color/finish availability and other faucet choices, please see
the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to desired
bathing temperature.
REMINISCENCE™ DROP-IN
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
© 2005 American Standard Inc.
229 x 305mm
(9 X 12)
FLOOR
CUTOUT
1-1/2 N.P.T.M. THREADS
ROUGH
FLOOR
1-1/2 O.D.TAILPIECE
70mm
(2-3/4)
117mm
(4-5/8)
LEVELING STRINGER
(NOT FOR SUPPORT)
RIM AT
DRAIN END
C/L OF OVERFLOW
616mm
(24-1/4)
73mm
(2-7/8)
464mm
(18-1/4)
79mm
(3-1/8)
149mm REF.
(5-7/8)
64mm REF.
(2-1/2)
1676mm
(66)
PUMP
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
914mm
(36)
457mm
(18)
330mm
(13)
INTEGRAL
FITTING DECK
152mm
(6)
C/L OF
DRAIN
OUTLET
OUTLINE OF
CUTOUT
ON/OFF
SWITCH
INTEGRAL
SUPPORT
FEET
SAFE-T-HEATER
REMOVABLE BLANK
73mm
(2-7/8)
464mm
(18-1/4)
229 x 305mm
(9 X 12)
FLOOR
CUTOUT
1-1/2 N.P.T.M. THREADS
ROUGH
FLOOR
1-1/2 O.D.TAILPIECE
70mm
(2-3/4)
117mm
(4-5/8)
LEVELING STRINGER
(NOT FOR SUPPORT)
RIM AT
DRAIN END
C/L OF OVERFLOW
616mm
(24-1/4)
79mm
(3-1/8)
149mm REF.
(5-7/8)
64mm REF.
(2-1/2)
INTEGRAL
SUPPORT
FEET
1676mm
(66)
914mm
(36)
457mm
(18)
330mm
(13)
INTEGRAL
FITTING DECK
152mm
(6)
C/L OF
DRAIN
OUTLET
OUTLINE OF
CUTOUT
66 x 36 x 24-1/4 In. (1676 x 914 x 616mm)
95 Lbs. (43 Kg.)
659 Lbs. (299 Kg.)
68 Gal. (257 L.)
55 Gal. (208 L.)
40 x 18 In. (1016 x 457mm)
53 x 28 In. (1330 x 718mm)
15 In. (381mm)
40 Lbs./Sq. Ft. (191 Kgs/Sq. m.)
23.8
44.5
GENERAL SPECIFICATIONS FOR 2908 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.6 HP, 9.7 AMPS, 120V.
2.1 HP, 15.6 AMPS, 120V.
SYSTEM I PUMP
SYSTEM II PUMP
66 x 36 x 24-1/4 In.
(1676mm x 914 mm x 616mm)
95 Lbs. (43 Kg.)
659 Lbs. (299 Kg.)
68 Gal. (257 L.)
40 x 18 In. (1016 x 457mm)
53 x 28 In. (1330 x 718mm)
15 In. (381mm)
39 Lbs./Sq. Ft. (187 Kgs/Sq. m.)
23.8
44.5
GENERAL SPECIFICATIONS FOR 2908 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA
TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL
SUPPORT REQUIRED.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
  • Page 1 1
  • Page 2 2

American Standard 2908.018WC User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI