Cambridge Audio INCOGNITO KP10 EU User manual

Brand: Cambridge Audio

Model: INCOGNITO KP10 EU

Category: Soundbar speakers

Type: User manual

KP10

A-BUS keypad

Installation Guide

2 Incognito KP10

CONTENTS

Introduction.......................................................3

System options.................................................4

Installation notes..............................................8

Rear panel connections.................................10

Keypad controls..............................................12

Operating instructions....................................14

Local source selection....................................16

Remote control................................................17

Technical specifications.................................18

Limited warranty.............................................19

Incognito A-BUS keypad 3

Thank you for purchasing this Cambridge Audio Incognito product. Incognito is a cost-effective,

modular based system using standard Cat-5 or Cat-6 cable to distribute hi-fi quality sound and

video around a home.

The KP10 is an in-wall, A-BUS

compatible amplified keypad with buttons for control of speaker

volume levels, Standby/On and source select (with compatible equipment), as well as having an

IR window for receiving remote control signals. The KP10 can connect to A-BUS hubs, A-BUS

Ready receivers, or to the Incognito Ready outputs of Cambridge Audio receivers and amplifiers

using Cat-5 wiring. The KP10 then connects to speakers using conventional speaker cable.

The KP10 keypad fits into any wall and is available with different finishes to compliment various

decorative schemes. The KP10 is fitted on the wall by fixing it into a standard single UK 47mm

electrician’s back-box. All knock-outs in the back-box should be removed to provide maximum

ventilation. Care should be taken in choosing a site for the KP10, and always refer to the

precautions in this guide. Bear in mind it is not always preferable to fit the KP10 next to a light

switch, particularly if the faceplates will differ.

Thanks for taking the time to read this manual, we do recommend you keep it for future

reference.

Matthew Bramble

Technical Director

INTRODUCTION

KP10 A-BUS keypad

The KP10 keypad can be used in two main configurations:

1. As part of a full Incognito system, where it is plugged into an Incognito hub (AH10), perhaps

with other Incognito accessories such as a video switching unit (VH10) or local input module

(LM10) fitted.

2. Where the keypad is plugged directly into an A-BUS Ready/Incognito Ready output of a

compatible Cambridge Audio (or other brand) A/V Receiver or Amplifier, no other accessories

are possible other than the required power supply and remote control/s.

The KP10 has two modes of operation to support these configurations, AH10 mode and

Standard A-BUS/Incognito Ready mode. The modes are selected by setting the Mode switch,

located on the rear of the KP10.

Note: Setting the Mode switch to the wrong setting can cause erroneous operation!

Full Incognito system

For use in a full Incognito system (see diagram opposite) the Mode Switch MUST be in the "AH10"

position as shown below:

Please consult the AH10 Incognito Multi-Room Installation Guide for full details of the various

options available for the full Incognito system.

4 Incognito KP10

SYSTEM OPTIONS

Std. A-BUS/

Incognito

Ready

AH10

Mode

Std. A-BUS/

Incognito

Ready

AH10

KP10-EU rear

Incognito A-BUS keypad 5

Speaker cable

PS10

Speaker cable

SS10 SS10

AH10

Cat-5/5e cable

KP10-EU KP10-EU

KP10 A-BUS keypad

A-BUS Ready / Incognito Ready

For use with an A-BUS Ready/Incognito Ready unit (see diagram opposite) the Mode switch

MUST be in the "Standard A-BUS/Incognito Ready" position as shown below:

In this configuration the keypad is wired directly to the amplifier/receiver. A Power Supply Unit

(PS10) is also required to power the one or two keypads as shown.

To allow control of your source equipment from the remote rooms an IR emitter (IR10) is plugged

into one of the IR outputs on the rear of the unit and then attached over the IR window of the

source unit. Alternatively, on our own products that feature IR emitter Inputs, a mini-jack to mini-

jack lead can be used.

Commands received by the keypads can now be sent back to the source equipment via the

amplifier. It is then possible to control the source equipment from the remote rooms by using the

source equipment's own remote controls or through a learning remote. The Incognito LR10

Learning Remote can fully control the keypads, “learn” the source's remote controls and change

source input on the amplifier etc.

6 Incognito KP10

Std. A-BUS/

Incognito

Ready

AH10

Mode

Std. A-BUS/

Incognito

Ready

AH10

KP10-EU rear

Incognito A-BUS keypad 7

Impedance 4 - 8 ohms

Loudspeaker Terminals

Important

Please ensure that loudspeaker terminals are fully tightened

Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées

Impedance 4 - 8 ohms

Right Left Right Left

Left

LeftRight Right

IR1

IR2 IR4

IR3

Keypad 1 Keypad 2

Pre-Out Tape In Rec Out 1 Rec Out 2 AV / MD DVD Tuner / DAB CD Aux

Pre-Out

Tape In

Rec Out 1

Rec Out 2

AV / MDDVD

Tuner / DAB

Aux

Right

Left

Right

Left

Power AC

Max Power Consumption: 700W

Off

Power

Mains Voltage Selector Switch (50 / 60Hz)

In Out

Control Bus

Caution Risk of electric shock. Do not open. Avis Risque de choc electrique. Ne pas ouvrir. Achtung Vorm öffnen des gërates. Netzstecker ziehen.

IR Emitter

PSU

azur 640A Integrated Amplifier V2.0

Designed in London, England

www.cambridge-audio.com

Manufactured in an

ISO9002 approved facility

Fault requiring

service (DC)

Over temperature

Temporary overload

Loudspeaker short

Protection LED

indicators:

Please refer to

your User's Manual

for more information

CAP5

Clipping

Vol Auto

Multi-Room

International Patent Pending LeisureTech Electronics Pty Ltd

azur 640C

Compact Disc Player

Standby / On

Stop

Play

Pause

Open

Skip

Scan

Line Output

Right

Left

Power AC

Class 1 Laser Product

Luokan 1 Laserplaite

Klass 1 Laserapparat

Mains Voltage Selector Switch (50 / 60Hz)

On Off

Power

Risk of electric shock

Do not open

Caution

Risque de choc electrique

Ne pas ouvrir

Avis

Vorm offnen des gerates

Netzstecker ziehen

Achtung

azur 640C Compact Disc Player V2.0

Max Power Consumption: 18W

www.cambridge-audio.com

Designed in London, England

Manufactured in an

ISO9002 approved facility

IR Emitter

In InOut

Control Bus

S/P DIF

Co-axial

Toslink

Optical

Digital Outputs

PS10

SS10 SS10

LR10

KP10-EUKP10-EU

IR10

Mini-jack lead

Cat5/5e cable

Speaker cable Speaker cable

Amplifier

(eg 640A V2.0)

CD player

(eg 640C V2.0)

KP10 A-BUS keypad

8 Incognito KP10

The KP10 is fitted on the wall by fixing it into a standard UK 47mm depth single-gang

electrician’s back-box (pattress). All knock-outs in the back-box should be removed to provide

maximum ventilation.

Where it is desired to fit a mains lighting switch etc next to a keypad, a barrier-box or two single

back-boxes must be used (bear in mind it is not preferable to fit the keypad next to a light-switch

particularly if the faceplate styles will differ). Only a qualified electrician should attempt such

installations.

Avoid fitting the KP10 where there is line of sight to another KP10. In such situations both

keypads may pick up the same commands from a remote control and it will be difficult to control

each zone independently.

Avoid fitting the KP10 where there is line of sight to the source equipment for the system. In such

situations the source equipment may pick up the same IR commands directly as are picked up

by the keypad and sent to the source equipment. This can interfere with the remote operation of

the source equipment.

Do not fit the keypad in areas directly lit by strong sunlight or where it will be strongly lit by

fluorescent tubes. These can be sources of infra-red energy which can interfere with the remote

control operation of the system. Some plasma televisions can radiate a lot of infra-red energy

and care should be taken if fitting a KP10 near a plasma screen television. Avoid placing the

KP10 near to dimmer switches or other items, which generate a lot of electrical noise.

INSTALLATION NOTES

Incognito A-BUS keypad 9

Safety precautions

Care should be taken when choosing the site for a KP10, the keypad must never be installed in a

back-box which also contains mains wiring or in areas of high humidity.

The KP10 runs on 24 V DC supplied through the connecting cable. As such there is no mains

voltage present in the KP10 and the unit is often safe to fit in areas where only extra low voltage

(ELV) equipment is permitted. However, it is imperative that you always check the wiring

regulations in force for your application and area.

Faceplates

The KP10 faceplate system is based on the 50 x 50 ‘easy-clip’ module standard and is

interchangeable with the wide range of faceplates made by manufacturers such as MK Electric,

RPP etc that conform to this standard. If it is desired to fit another faceplate, it can be replaced

by gently prising apart the KP10 faceplate and snapping on another in its place.

Fitting the keypad

Remove the supplied faceplate from the KP10 by gently prising apart. It will “pop” off. Connect

each wire in the Cat-5 cable to its respective terminal in the screw-down connector on the back

of the KP10 (refer to the Cat-5 to KP10 screw-down connectors diagram in the ‘Rear panel

connections’ section of this guide). The recommended maximum length for use with standard

Cat-5 cable is 30m from hub to keypad in total (screened Cat-5 cable can also be used). After

making the wiring connections, fit the KP10 to the back-box with the two supplied M3.5x20

screws. Gently push the faceplate back on to the module.

Note: If in doubt about any aspect of installation or wiring, seek professional advice from a

qualified installer.

KP10 A-BUS keypad

Cat5 to KP10 punch down connectors

A Cat-5 cable (terminated with an RJ45 jack

plug) is used to connect the KP10 to an AH10

hub or A-BUS Ready receiver. The KP10 has

punch down connectors for the eight

individual conductors of the Cat-5 cable (use a

small flat-bladed screwdriver). See below for

the EIA/TIA 568A wiring standard:

10 Incognito KP10

REAR PANEL CONNECTIONS

R+R-L-L+

blue

blue/white

orange

brown/white

brown

orange/white

green

green/white

34567821

View from

contact end

Gather pairs, trim and

insert into RJ45 plug

Crimp wires

securely in place

brown / white

brown

blue / white

blue

green / white

green

orange / white

orange

R+

R- L- L+

Incognito A-BUS keypad 11

Line-in/Line-out

connections

on subwoofer

Screened audio cable

Preamp

output

connections

on rear of

KP10

Gain adjust

The maximum output of the KP10 can be limited by turning these down. Alternatively, if the sound

level is too quiet, the Gain can be turned up.

Mode switch

Selects between AH10 mode and Standard A-BUS Ready/Incognito Ready mode.

Speaker output

Connect to a pair of speakers with two runs of standard high-quality speaker cable. Speakers of

at least 88 dB SPL for 1W @ 1 metre efficiency should be used with the KP10. Speakers from 4–8

ohms can be used. The Incognito SS10 speakers are an ideal match.

LK10 option

Allows control of source equipment via an LK10 Learning Keypad.

Preamp output

A preamp output is provided for optional use driving a powered subwoofer or auxiliary amplifier.

Connection from the preamp output to other equipment should be by screened audio cable (see

diagram below).

KP10 A-BUS keypad

12 Incognito KP10

The six LEDs indicate the function status

of the KP10. Listed below are each of the

functions of the corresponding LEDs:

Minimum volume / Source select

Volume / Source select / Bass adjust

/ Local Source Selection Mode

Volume / Source select / Treble adjust

/ Local Source Selection Mode

Volume / Source select / Balance

adjust / Local Source Selection Mode

Volume / Source select / Fader adjust

/ Local Source Selection Mode

Maximum volume / Source select

For full instructions on volume adjustment,

source selection, sound adjustment and

local source selection modes, refer to the

‘Operating instructions’ section of this

guide.

KEYPAD CONTROLS

Incognito A-BUS keypad 13

Standby/On

Press to switch the keypad between On and Standby mode. By pressing and holding the

Standby button for about 2 seconds, all KP10s connected to the AH10 hub will be turned

off. If the KP10 is connected to a Cambridge Audio Incognito Ready Amplifier rather than

an AH10 hub, the amplifier will be turned off.

Volume up

Press to increase the volume or other sound adjustment.

Source select (right)

Use this key to select the current active source.

Volume down

Press to decrease the volume or other sound adjustment.

Source select (left)

Use this key to select the current active source.

IR window

Point the Incognito LR10 Learning Remote towards this window. A small flashing LED

behind this window indicates operation.

KP10 A-BUS keypad

14 Incognito KP10

OPERATING INSTRUCTIONS

Important!

As mentioned previously, the KP10 can be switched between two modes of operation; a

standard A-BUS mode for compatibility with other manufacturers A-BUS Ready equipment

(Standard A-BUS/Incognito Ready mode), and an Incognito A-BUS hub mode (AH10 mode).

When used with other manufacturers A-BUS Ready equipment the keypad MUST be switched to

“Standard A-BUS/Incognito Ready” mode or they will not work.

Volume adjustment

Volume is adjusted using the volume up and volume down buttons on the keypad or remote; this

is indicated on the keypad by the intensity of the blue LED lights, there are four levels of intensity.

Source selection

The Source left and right buttons allow you to choose from multiple connected sources. The LED

display will indicate which source is selected.

Sound adjustment modes

Pressing the Power/Standby button while holding the Volume down key activates the sound

adjustment modes, the four central LEDs on the keypad will then light in sequence to indicate

each of the four sound adjustment modes; Bass, Treble, Balance and Fader. These modes can

also be activated using the 'Select' button on the remote control.

After holding both buttons down for a short

period, the second LED on the keypad will light

indicating that Bass adjust mode has been

activated. In this mode pressing the Volume

up/down keys will adjust the Bass (low

frequencies) level.

Continuing to hold both keys down will light the

third LED indicating that Treble adjust mode

has been activated. In this mode pressing the

Volume up/down keys will adjust the Treble

(high frequencies) level.

Continuing to hold both buttons will light the

fourth LED indicating that Balance adjust mode

has been activated. In this mode pressing the

Volume up/down keys will adjust the sound

level between the left and right speakers.

Continuing to hold both buttons will light the fifth LED indicating that Fader adjust mode has

been activated. In this mode pressing the Volume up/down keys will adjust the balance between

the main speakers and anything that is connected to the preamp output. This adjustment only

being relevant if the preamp output is used. The volume up and down buttons on the remote

control can also be used to adjust the sound in each mode.

Note: If no adjustment is made the system will automatically go back to volume adjustment after

two seconds.

Incognito A-BUS keypad 15

Bass Treble Balance Fader

KP10 A-BUS keypad

16 Incognito KP10

Note: This feature is only available if the KP10

is part of a full Incognito multi-room system with

one or two Local Input Modules (LM10) fitted.

The local source selection mode will need to be

activated to configure the KP10 correctly. This

mode is only available when the Mode Switch is

set to “AH10” mode. LM10s can only be used in

this mode. Please refer to your LM10

Installation Guide for more information.

Pressing the Select left or right buttons on the

keypad allows you to rotate through all six

sources as default. However, it is possible to

allow the addition of one or two local sources by

accessing Local source selection mode. To

enter this mode press the Volume up button

simultaneously with the Power button for four seconds; the LED display will then scroll through

the sequence shown in the illustration right and described as follows:

After holding both buttons down for a short period, LED 2 will light indicating that Sources 1–6

(default) are available for selection.

Continuing to hold both keys down will light LED 3 indicating that Sources 1–6 + Local source 1

mode is available for selection.

Continuing to hold both buttons will light LED 4 indicating that Sources 1–6 + Local source 1 +

Local source 2 mode is available for selection.

LOCAL SOURCE SELECTION

3 4 5

Incognito A-BUS keypad 17

Continuing to hold Volume up and Power buttons will light LED 5, to indicate that Off mode is

available for selection, and no source will be selected.

To select these modes, wait till the corresponding LED is lit and then release Power and

Volume up buttons.

Note: If no adjustment is made the system will automatically go back to volume

adjustment after two seconds. If “Standard A-BUS/Incognito Ready” mode is selected on

the Mode switch, the KP10 will only rotate round the main 6 sources.

REMOTE CONTROL

The KP10 can be used with the Incognito LR10 remote control,

a sophisticated learning remote which is able to learn the

codes of all the source equipment remotes. Once programmed

the user can thus use the LR10 to perform all operations from

one remote.

The LR10 is also suitable where the KP10 is to be connected to

the A-BUS Ready outputs of AV receivers and amplifiers instead

of one of our hubs as it can learn the relevant source change

commands etc of the receiver or amplifier as well as the source

equipment.

Note: Please refer to the Incognito LR10 manual for further

information.

KP10 A-BUS keypad

18 Incognito KP10

Input impedance 45 k ohms

Frequency response 20Hz – 20kHz +/- 1dB

THD <0.2% @ 1W, 20Hz – 20 kHz

S/N ratio > 80 dB ‘A’ weighted

Volume control range - 80 dB, 36 steps

Bass control range +/- 16 dB, 2 dB steps

Treble control range +/- 16 dB, 2 dB steps

Balance control range +/- 40 dB, 9 steps either way

Preamp output Variable level, follows volume setting

IR pass through 34–40 kHz and 54–58kHz

modulation frequencies supported

Speaker impedance 4–8 ohms

Power requirement 24V DC @ 1A max (supplied by hub)

This guide is designed to make installing and using this product as easy as possible. Information in this document has been carefully

checked for accuracy at the time of printing; however, Cambridge Audio's policy is one of continuous improvement, therefore design and

specifications are subject to change without prior notice. If you notice any errors please feel free to email us at:

[email protected]

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be

reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. All

trademarks and registered trademarks are the property of their respective owners.

A-BUS and A-BUS Ready are registered trademarks of LeisureTech Electronics Pty Ltd Australia.

TECHNICAL SPECIFICATIONS

Incognito A-BUS keypad 19

Cambridge Audio warrants this product to be free from defects in materials and workmanship (subject to the terms set forth

below). Cambridge Audio will repair or replace (at Cambridge Audio’s option) this product or any defective parts in this

product. Warranty periods may vary from country to country. If in doubt consult your dealer and ensure that you retain proof

of purchase.

To obtain warranty service, please contact the Cambridge Audio authorised dealer from which you purchased this product. If

your dealer is not equipped to perform the repair of your Cambridge Audio product, it can be returned by your dealer to

Cambridge Audio or an authorised Cambridge Audio service agent. You will need to ship this product in either its original

packaging or packaging affording an equal degree of protection.

Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that this product is within the warranty

period, must be presented to obtain warranty service.

This warranty is invalid if (a) the factory-applied serial number has been altered or removed from this product or (b) this

product was not purchased from a Cambridge Audio authorised dealer. You may call Cambridge Audio or your local country

Cambridge Audio distributor to confirm that you have an unaltered serial number and/or you purchased from a Cambridge

Audio authorised dealer.

This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial

use, or modification of, or to any part of, the product. This warranty does not cover damage due to improper operation,

maintenance or installation, or attempted repair by anyone other than Cambridge Audio or a Cambridge Audio dealer, or

authorised service agent which is authorised to do Cambridge Audio warranty work. Any unauthorised repairs will void this

warranty. This warranty does not cover products sold AS IS or WITH ALL FAULTS.

REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE

CONSUMER. CAMBRIDGE AUDIO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW,

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER

INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE.

Some countries and US states do not allow the exclusion or limitation of incidental or consequential damages or implied

warranties so the above exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other

statutory rights, which vary from state to state or country to country.

LIMITED WARRANTY

KP10 A-BUS keypad

Incognito KP10-EU

www.cambridge-audio.com

Part No. AP18303/2

Cambridge Audio INCOGNITO KP10 EU User manual

Brand: Cambridge Audio

Model: INCOGNITO KP10 EU

Category: Soundbar speakers

Type: User manual

Download PDF

report

Cambridge Audio INCOGNITO KP10 EU User manual

Cambridge Audio INCOGNITO KP10 EU User manual

Related papers

Other documents