Reely 1661756 Operating instructions

Brand: Reely

Model: 1661756

Category: Battery chargers

Type: Operating instructions

This manual is also suitable for

Page is loading ...

There are no components for you to adjust or maintain within the device.

• The product is not a toy and does not belong in the hands of children! The product

may only be set up, used or stored in places that are not accessible to children.

The same applies to rechargeable batteries. Children could short-circuit the

rechargeable battery/battery pack, which may cause an explosion. This presents

a danger to life!

• The product design corresponds to the protection-class II (double or reinforced

isolation). Make sure that the insulation (of the casing or the output cable) is

neither damaged nor destroyed.

• The charger is designed for operation from a power outlet with rated voltage of

100 - 240 V/AC, 50/60 Hz. Never operate the device on a different voltage/

frequency.

The outlet must be located in direct proximity to the device and easily accessible.

• Do not pull the mains plug from the mains socket by pulling on the cable!

• In schools, educational centres, hobby and self-help workshops, the operation of

the product is to be supervised by trained employees.

• In commercial institutions, the accident prevention regulations of the Employer’s

Liability Insurance Association for Electrical Systems and Operating Facilities are

to be observed.

• Do not leave packaging material carelessly lying around. It may become a dan-

gerous plaything for children!

• If in doubt about how to connect the device correctly, or should any questions

arise that are not answered in these operating instructions, please contact our

technical service or another specialist.

b) Installation location

• The product may be used only in dry areas indoors. It may not get wet or damp;

there is danger of electric shock!

Do not use the charger within a vehicle.

 • Selectastable,at,clean,andsufcientlylargeplaceforthecharger.

  Donotplacethechargeronaammablesurface(e.g.carpet,tablecloth).Always

useasuitable,non-ammable,heatproofbase.

Do not place the charger on surface of valuable furniture without suitable protec-

tion. The impact of heat could lead to colour or material changes.

  Keepthechargerawayfromeasilyammablematerials(e.g.drapes,paper),

liquids (e.g. gasoline) or gases.

• Avoid direct sunlight, strong heat or cold. Keep the product away from dust and

dirt.

 • Donotuseintheimmediatevicinityofstrongmagneticorelectromagneticelds,

transmitter aerials or RF generators. This can impact the electric control system.

 • Donotplaceanycontainerslledwithliquid,e.g.vasesorplants,onornextto

the charger.

If these liquids get into the interior of the charger, it will be destroyed, and there is

alsoahighriskofareoranexplosion.

In this case, switch off immediately the mains socket to which the charger is con-

nected (switch off at the corresponding circuit breaker or remove the safety fuse,

then switch off the respective earth leakage circuit breaker).

Then remove the battery from the charger and pull the mains plug out of the

mains outlet.

Allow the battery and charger to dry, and then have it checked by a specialist

workshop or dispose of the product in an ecologically sound fashion.

• Make sure that the mains cable is not pinched or damaged by sharp edges. A

damaged power cable may never be used again! Place the cable so that nobody

can trip over it.

c) Operation

• Only LiPo batteries may be charged by this charger (rated voltage per cell 3.7 V).

Never charge any other batteries (e.g. NiMH, NiCd or lead batteries) or non-

rechargeablebatteries.Thereisagreatriskofreorexplosion!

• Only connect a single battery to the charger.

 • Maintainsufcientdistancetoammableobjects.Allowadequatedistance

between the charger and the battery (min. 20 cm), and never put the battery onto

the charger.

OPERATING INSTRUCTIONS

CHARGER

ITEM NO. 1409523 (TYP “V-CHARGE ECO LIPO 2000”)

ITEM NO. 1409525 (TYP “V-CHARGE ECO LIPO 3000”)

INTENDED USE

The charger is intended for charging LiPo batteries (Item No. 1409523 = 2 - 3 cells; Item No.

1409525 = 2 - 4 cells) with rated cell voltage of 3.7 V. Please note data of charging current,

charging voltage etc. provided in chapter “Technical Data” at the end of these operating

instructions.

The charger is equipped with a built-in power supply unit (operating voltage 100 - 240 V/AC,

50/60 Hz); connect the charger to the voltage/current supply via the supplied power cord to a

regular power outlet.

Always observe the safety instructions and all other information included in these operating

instructions!

Read the operating instructions closely and carefully, and keep them for later reference. If you

pass the product on to a third party, please pass on these operating instructions as well.

Use other than that described above can lead to damage to the product and may involve

additionalriskssuchas,forexample,shortcircuits,re,electricalshocksetc.Nopartofthe

productmaybemodiedorrebuilt,andthehousingmustnotbeopened!

This product complies with the applicable National and European requirements. All names of

PACKAGE CONTENTS

• Charger

• Power cable

• Operating instructions

Up-to-date operating instructions:

1. Open www.conrad.com/downloads in a browser or scan the

displayed QR code.

2. Select document type and language and enter the item number

intothesearcheld.Aftersubmittingthequeryyoucandownload

displayed records.

EXPLANATION OF SYMBOLS

The lightning symbol inside a triangle is used when there is a potential risk of

personal injury, such as electric shock.

An exclamation mark in a triangle indicates important instructions in this operating

manual which absolutely have to be observed.

The “arrow” symbol is used where special tips and notes on operation are provided.

SAFETY INSTRUCTIONS

The warranty will be void in the event of damage caused by failure to observe

these safety instructions! We do not assume any liability for any resulting

damage!

We do not assume any liability for personal injuries and material damages

caused by the improper use or non-compliance with the safety instructions!

In such cases, the warranty will be null and void.

Dear Customer, the following safety instruction is intended not only for the protec-

tion of your health, but also for the protection of the product.

Therefore, please read the following points very carefully before connecting and

usingtheproductforthersttime.

a) General

 • Theunauthorisedconversionand/ormodicationoftheproductisnotpermitted

for safety and approval reasons (CE). Never dismantle the product.

• Maintenance, adjustment, or repair work should be carried out only by a special-

ist/specialist workshop.

VERSION 02/16

• Charge the batteries about every 3 months; otherwise self-discharge can lead to a

so-called deep discharge, which causes the batteries to become unusable.

• Disconnect the battery from the charger when the battery is fully charged.

• When used incorrectly (i.e. through an excessive charging current or incorrect

polarity), the rechargeable battery can be overcharged or destroyed. In the worst

case, the rechargeable battery can explode and thereby cause serious damage.

• Never damage the battery, never let the battery fall, do not pierce the battery with

any objects! Avoid applying any mechanical loads to the battery, never pull on the

battery’sconnectorcables!Thereisariskofreandexplosion!

These guidelines must also be observed when the battery is inserted into the

model (if the model is removed, for example).

• Ensure that the battery does not overheat during usage, recharging, discharging,

transport or storage. Do not place the battery adjacent to sources of heat (e.g.

cruise control, motor), keep the battery away from direct sunlight. There is a risk

ofreandexplosionifthebatteryoverheats!

• The battery must not reach a temperature of more than +60 °C (any additional

manufacturer warnings with other limitations must also be heeded as applicable!).

• If the battery is visually damaged do not use it any longer. Do not recharge it.

Thereisariskofreandexplosion!

Only touch the battery with care, use suitable protective gloves.

Dispose of the battery in an ecologically sound fashion.

• If the battery manufacturer provides no information as to maximum permissible

charge current, charge the LiPo battery with the maximum current of 1C. This

means that the charging current may not exceed the capacity value imprinted on

the accumulator (e.g. accumulator capacity 3000 mAh, max. charge current

3000 mA = 3 A).

• Follow any additional safety guidelines of the manufacturer of the used recharge-

able battery/battery pack.

CONNECTIONS AND CONTROL ELEMENTS

1 Mains socket

2 Four LEDs to indicate battery status

3 XH sockets for connection of a LiPo battery

The charger “V-CHARGE ECO LiPo 2000” is

equipped with two XH sockets (for a 2-cell or

3-cell LiPo battery).

The charger “V-CHARGE ECO LiPo 3000”

(see picture) is equipped with three XH sock-

ets (for a 2-cell, 3-cell or 4-cell LiPo battery).

Only connect a single battery to the

charger at a time. Always use only one of the XH sockets at a time.

If more than one battery is connected to the charger, both the charger and battery

can be damaged!

PUTTING INTO OPERATION AND USE

• Connect the power socket (1) with an appropriate mains socket via the supplied power

cable.AfterafewsecondstheLEDs25%/75%and50%/100%areashingalternately.This

indicates that no rechargeable battery is connected and that the charger is ready.

• Connect the jack socket (1) with a mains outlet via the supplied power cord.

• Placethechargeronalevel,at,stablesurface.Protectvaluablefurnituresurfacesby

using a suitable mat to prevent scratches, pressure points or discolourations.

The housing of the charger heats up during operation. Make sure that the charger is

always adequately ventilated; never cover it while in operation.

• DisconnecttheLiPobatteryfromthespeedorightcontroller.

• Connect the battery to be charged via its XH balancer plug with the relevant socket (3) of

the charger. At that, observe the correct polarity of the XH plug. When connecting, do not

use excessive force; always use a socket matching the plug.

• As both the charger and the battery heat up during the charge/discharge proce-

dure,itisnecessarytoensuresufcientventilation.Nevercoverthechargerand/

or the connected battery.

• Do not operate the product unattended. Although there is a wide range of

comprehensive safety mechanisms on the device, it is impossible to exclude the

possibility of malfunctions or problems occurring while charging a battery.

• When you work with the charger or rechargeable batteries, never wear metallic

or strongly conductive materials, such as jewellery (necklaces, bracelets, rings or

similarobjects).Ashortcircuitatthebatteryorchargerposesadangerofreand

explosion.

• Never leave batteries connected to the charger, if the charger is not in use.

Disconnect the charging set from the mains voltage. Pull the mains plug out of

the mains socket. Afterwards, keep the product in a clean and dry place out of

children’s reach.

• Only use the device in a moderate climate, do not use it in a tropical climate.

For more information on acceptable environmental conditions, see the chapter

“Technical Data”.

• Never use the product immediately after it has been brought from a cold room into

a warm one. The resulting condensation may lead to malfunctions or damage un-

der certain circumstances! Furthermore, this could cause a lethal electric shock!

Allow the charger (and the battery/batteries) to reach room temperature before

connecting the charger to the mains supply and using it. This may take several

hours!

• Handle the product with care. The product can be damaged if crushed, struck,

dropped even from a low height or subjected to mechanical pressure and vibra-

tions.

• If it can be assumed that safe operation is no longer possible, the product must be

turned off and precautions must be taken to ensure that it is not used unintention-

ally.

It can be assumed that safe operation is no longer possible if the product is visibly

damaged, the product does not work at all, if it was stored long-term in unfavour-

able conditions, or if it was exposed to heavy loads during the transport.

d) Handling rechargeable batteries

• Keep batteries out of the reach of children. Always keep batteries out of the reach

of children.

• Do not leave the batteries lying around in the open; there is a risk of them being

swallowed by children or domestic animals. In such a case, call a doctor immedi-

ately!

• Rechargeable batteries must never be short-circuited, dismantled or thrown into

re.Thereisariskofreandexplosion!

• If your skin comes into contact with leaking or damaged batteries, you may suffer

burns. For this reason you should use suitable protective gloves in this case.

• If any battery connector cables need to be cut to size (e.g. if the battery is sup-

plied without a connector plug), cut each cable individually to prevent a short

circuitoccurring.Riskofreandexplosion!

• Use the charger to charge only the batteries with appropriate technology (LiPo).

Never try charging other batteries or non-rechargeable batteries using this device.

Thereisariskofreandexplosion!

Non-rechargeable batteries are meant to be used once only and must be dis-

posed of when empty. Charge rechargeable batteries intended for that use only.

• Batteries must not get damp or wet.

 • Neverdamagetheexteriorofabattery.Thereisariskofreandexplosion!

• Never charge/discharge rechargeable batteries unattended.

•

Never charge/discharge a battery directly in the model. First remove the battery

fromthemodel,disconnectittotallyfromspeedorightcontroller.

• When connecting the battery to the charger or model (e.g. model aircraft),

observe the correct polarity (plus/+ and minus/-). Should you connect the battery

incorrectly, not only will the model be damaged but also the battery. There is a risk

ofreandexplosion!

• Do not charge any battery that is still hot (e.g. due to high charge current from the

model). Allow the battery to cool down to room temperature before attempting to

charge it again.

• Never charge/discharge damaged, leaking or deformed batteries. This can result

inareorexplosion!Disposeoftheunusablebatteryinanecologicallysound

fashion.

• Never use a LiPo battery composed of different types of cells.

Legal notice

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent

the technical status at the time of printing.

TECHNICAL DATA

Charger type V-CHARGE ECO LiPo 2000 V-CHARGE ECO LiPo 3000

Item no. 1409523 1409525

Operating voltage 100 - 240 V/AC, 50/60 Hz

Protection class II

Charging sockets XH balancer connector

Appropriate battery type LiPo (with rated voltage per cell 3.7 V)

Number of cells 2 - 3 2 - 4

Battery capacity 800 - 5000 mAh 800 - 8000 mAh

Charging current max. 2 A ±10% max. 3 A ±10%

Charging capacity 25 W 35 W

Cut-off voltage 4.24 V (per cell)

Balancer current 400 mA

Short-circuit protection yes

Overload protection yes

Ambient conditions Temperature +10 °C to +40 °C,

air humidity 0% to 90% relative, not condensing

Dimensions (W x L x H) 70 x 110 x 40 mm 72 x 117 x 40 mm

Weight 161 g 178 g

Assignment of the XH sockets is imprinted on the charger upper side. As a rule, one of

the cables of the XH plug is marked at the battery with colour (or is black). Besides, the

XHplugtsintomatchingsocketofthechargeronlyinoneposition.

If your battery has a balancer connector with other plug type than XH, there will be a

matching adapter in the accessories trade.

Only connect a single battery to the charger at a time. Always use only one of the

XH sockets at a time.

 PleasenotethatonlyaLiPobatteryofserialcongurationcanbecharged(marked

e.g. as 2S, 3S, 4S).

Special batteries with e.g. connectors of both cells led out separately cannot be

charged by this charger.

• The charger starts the charging process and charges the LiPo battery via its balancer

connector. Adaptation of the cell voltages occurs at the same time, so that all cells have the

samevoltageafterthechargingprocessiscompleted(insignicantdeviationsdependon

technical factors).

The charging current or capacity of the charger (see chapter “Technical data”) is divided to

cells depending on their number. The more cells the connected battery has, the longer is

the charging process.

• Four LEDs on the charger indicate the charging status (25%, 50%, 75% and 100%).

Once the LED “100%” lights up, the battery is fully charged. Disconnect the battery from

the charger.

• Now, either connect another battery for charging, or disconnect the charger from the mains

voltage. Pull the mains plug out of the mains socket.

Keep the product in a cool, dry, dust-free place out of the reach of children.

CLEANING AND MAINTENANCE

The product does not require any maintenance and should never be disassembled for any

reason.

Unplug the connected battery from the charger before cleaning. Disconnect then the charger

from the mains voltage. Pull the mains plug out of the mains socket.

Only clean the product with a soft, clean, dry cloth. Dust can be easily removed using a clean,

soft brush and a vacuum cleaner.

Never use aggressive cleaning agents or chemicals for cleaning; these can lead not only to

discolouration, but can also damage the product.

DISPOSAL

a) General

Electronic devices are recyclable material and do not belong in the household

waste.

Please dispose of the device, when it is no longer of use, according to current statu-

tory requirements.

b) Batteries and rechargeable batteries

As the end user, you are required by law (Battery Ordinance) to return all used batteries/

rechargeable batteries; disposal of them in the household waste is prohibited!

Batteries/rechargeable batteries contain harmful materials and are labelled with the

symbol shown to indicate that disposal in the household waste is forbidden. The

symbols of the relevant heavy metals are: Cd=Cadmium, Hg=Mercury, Pb=Lead

(name written on the battery/rechargeable battery, e.g., under the rubbish bin

symbol on the left).

Youcanreturnyourusedbatteries/rechargeablebatteriesfreeofchargeattheofcialcol-

lection points of your community, in our stores, or at places where batteries or rechargeable

batteries are sold.

Youtherebyfullyourstatutoryobligationsandcontributetotheprotectionoftheenviron-

ment.

Page is loading ...

Reely 1661756 Operating instructions

Brand: Reely

Model: 1661756

Category: Battery chargers

Type: Operating instructions

This manual is also suitable for

Download PDF

report

in other languages

français: Reely 1661756 Mode d'emploi
Deutsch: Reely 1661756 Bedienungsanleitung
Nederlands: Reely 1661756 Handleiding

Reely 1661756 Operating instructions

This manual is also suitable for

Reely 1661756 Operating instructions

in other languages

Related papers

Other documents