THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg., Inc. Page 1 Factory # 15713
Stock # MS49-084-005-08
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, do not return
this item to the store where it was purchased.
Please call our customer service number and have your instructions and parts list
ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
or e-mail your request to [email protected]
STOCK # MS49-084-005-08
LOT NUMBER:
DATE PURCHASED:
/ /
Stock # MS49-084-005-08
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg., Inc. Page 2 Factory # 15713
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use,
we will repair or replace it for up to one (1) year from date of purchase. Every Whalen
Furniture product is designed to meet your highest expectations. We guarantee that
you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which
vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST, Monday to Friday
www.whalenstyle.com
MANUFACTURER: Whalen Furniture
CATALOG: 5-PC Counter Height Dining Set (MS49-084-005-08)
DATE OF MANUFACTURE: June, 2012
MADE IN VIETNAM
MAXIMUM LOAD 400 lb. (181.4 kg)
MAXI MUM LOAD 300 lb. (136.1 kg)
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Please wait until all steps are completed before tightening bolts.
4. Make sure all bolts are tightly fastened before the unit is used.
GENERAL INFORMATION
,
TIPS & TRICKS
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
Stock # MS49-084-005-08
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg., Inc. Page 3 Factory # 15713
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are
present before beginning assembly.
A- Back Rest (4) B- Seat Panel (4) C- Left Leg Assembly (4) D- Right Leg Assembly (4)
E- Upper Front Stretcher (4) F- Upper Back Stretcher (4) G- Bottom Front Stretcher (4)
H- Bottom Back Stretcher (4) I- Top Panel (1) J- Table Leg (4)
(1) M6 x 35mm Bolt (2) M6 x 45mm Bolt (3) Small Lock Washer (4) Small Flat Washer
(12+1 extra) (40+1 extra) (20+1 extra) (52+1 extra)
(5) 1-1/2” Wood Screw (6) M8 x 75mm Bolt (7) Large Lock Washer
(48+1 extra) (8+1 extra) (8+1 extra)
(8) Large Flat Washer (8+1 extra) 4mm Allen Wrench (2) 5mm Allen Wrench (1)
Tools required: Allen Wrench (provided), Phillips Screwdriver (not provided).
Stock # MS49-084-005-08
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg., Inc. Page 4 Factory # 15713
Assembly Instructions for Chair
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Align and attach Seat Panel (B) onto the bottom of Back Rest (A) using two M6 x 45mm Bolts (2)
with Small Lock Washers & Flat Washers (3 & 4) through the counter sunk holes on Seat Panel
into the post of Back Rest. Fasten the bolts with 4mm Allen Wrench provided. See detail #1.
Note: DO NOT fully tighten the bolts.
3. Secure the Seat Panel (B) onto the Back Rest (A) by inserting three M6 x 35mm Bolts (1) with
Small Lock Washers & Flat Washers (3 & 4) through the counter sunk holes on Seat Panel into
the bottom rail of Back Rest. Fully tighten the bolts with 4mm Allen Wrench provided.
See detail #1A. Note: For the three middle holes (detail #1A) must use only M6 x 35mm Bolt (1).
Small Flat Washer
(5 used in this step)
④
Small Lock Washer
(5 used in this step)
③
M6 x 35mm Bolt (3 used in this step)
①
M6 x 45mm Bolt (2 used in this step)
②
Stock # MS49-084-005-08
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg., Inc. Page 5 Factory # 15713
Assembly Instructions for Chair
4. Position the Left Leg Assembly (C) on a flat and non-abrasive surface with the pre-drilled holes
facing up as shown in detail #2.
5. Attach Upper Front & Back Stretcher (E & F) onto the Left Leg Assembly (C) in place with the
wood dowels fully inserted into the pre-drilled holes without threaded inserts. Make sure the
screw holes point toward inside and facing down. Insert and screw the M6 x 45mm Bolts (2)
with Small Flat Washers (4) into the Stretcher through the pre-drilled holes. Tighten the bolts
with 4mm Allen Wrench provided. See detail #2A.
6. Fully insert the Bottom Front & Back Stretcher (G & H) into the pre-drilled holes on the Left
Leg Assembly. Make sure the slant screw holes on the bottom stretcher are facing down and the
Arrow UP stickers are facing in. Insert and screw the 1-1/2” Wood Screws (5) into the pre-
drilled holes underneath the stretcher. Tighten with Phillips Screwdriver. See detail #2.
Note: DO NOT fully tighten all the screws & bolts until the chair been adjust & level all the legs
so that they do not wobble.
Once adjusted then go back and tighten while making sure that the
unit remains level
.
7. Repeat the procedure to attach the Right Leg Assembly (D) at the opposite end.
Small Flat Washer
(8 used in this step)
④
M6 x 45mm Bolt (8 used in this step)
②
1-1/2” Wood Screw
(4 used in this step)
⑤
Stock # MS49-084-005-08
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg., Inc. Page 6 Factory # 15713
Assembly Instructions for Chair
8. Flip the installed leg assembly upside down and attach to the bottom of Seat Panel (B), using
the wood dowels pre-attached on the Upper Front & Back Stretcher (E & F) as guide, secure
with the 1-1/2” Wood Screws (5) through the pre-drilled holes on upper stretchers, a total of 8
screws. See detail #3.
9. Stand the unit upright.
10. Repeat the procedure to assemble the other Chairs.
1-1/2” Wood Screw
(8 used in this step)
⑤
Stock # MS49-084-005-08
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg., Inc. Page 7 Factory # 15713
Assembly Instructions for Table
11. Place the Top Panel (I) upside down on a non-abrasive surface as shown in detail #4
12. Attach Table Legs (J) to the Apron corners of Top Panel (I) in place using the M8 x 75mm Bolts
(6) with Large Lock Washers & Flat Washers (7 & 8) through the corner block into the
threaded sockets in the Leg. Tightly fasten the bolts with 5mm Allen Wrench provided. See
detail #4.
13. Stand the unit upright.
Your assembly should now be complete.
Thank you for your purchase.
Large Lock Washer
(8 used in this step)
⑦
M8 x 75mm Bolt (8 used in this step)
⑥
Large Flat Washer
(8 used in this step)
⑧
IF YOU NEED TO ORDER PARTS PLEASE USE THE LIST BELOW
5-PC Counter Height Dining Set
MS49-084-005-08
*MS49-084-005-08-1-TT Table Top *MS49-084-005-08-12-M6x45B M6 x 45mm Bolt
*MS49-084-005-08-2-TL Table Leg *MS49-084-005-08-13-SLW Small Lock Washer
*MS49-084-005-08-3-BR Back Rest *MS49-084-005-08-14-SFW Small Flat Washe
r
*MS49-084-005-08-4-SP Seat Panel *MS49-084-005-08-15-1 1/2WS 1 1/2” Wood Screw
*MS49-084-005-08-5-LLA Left Leg Assembly *MS49-084-005-08-16-M8x75B M8 x 75mm Bolt
*MS49-084-005-08-6-RLA Right Leg Assembly *MS49-084-005-08-17-LLW Large Lock Washer
*MS49-084-005-08-7-BFS Bottom Front Stretcher *MS49-084-005-08-18-LFW Large Flat Washer
*MS49-084-005-08-8-BBS Bottom Back Stretcher *MS49-084-005-08-19-M4AW 4mm Allen Wrench
*MS49-084-005-08-9-UFS Upper Front Stretcher *MS49-084-005-08-20-M5AW 5mm Allen Wrench
*MS49-084-005-08-10-UBS Upper Back Stretcher *MS49-084-005-08-21-CH Complete Hardware
*MS49-084-005-08-11-M6x35B M6 x 35mm Bolt
/
