Golden Lighting 4855-3 RBZ-SD Installation guide

Brand: Golden Lighting

Model: 4855-3 RBZ-SD

Type: Installation guide

This manual is also suitable for

Assembly Instructions: 4855-3 (Galveston)

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

1. PREPARING FOR INSTALLATION

Remove all of the contents from the carton. See

the important notes above. Shut off the power at

the circuit breaker and completely remove the old

xturefromtheceiling,includingtheoldmounting

strap.

From the parts bag remove the mounting strap

assembly. One end of nipple (F) should be attached

tomountingstrap(A)withwasherandhexnut(C,D)

in place. The other end should have canopy loop (H)

attached.Attachmountingstrap(A)tothejunction

box using mounting screws (B) and a screwdriver.

Tightensecurely.Unscrewcanopyloopcollar(I)from

canopy loop (H). Pass canopy (G) over the mounted

canopylooptotest the height. Approximatelyhalf

of the canopy loop’s exterior threads should be

exposed, and the canopy loop collar should t

snugly onto the canopy loop. Remove canopy (G)

andadjusttheheightofnipple(F)andcanopyloop

(H)untilthedesiredheightisreached.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

For Customer Service, contact

the place of purchase to arrange

for replacement parts.

BLACK

(Hot)

WHITE

(Neutral)

GREEN

(Ground)

HOUSE WIRES

SMOOTH

(Or Black)

FIXTURE WIRES

RIBBED

(Or White)

BARE COPPER

(Or Green)

UP - INSTALLATION

PLEASE NOTE:

Thisxturemaybe

mounted with the

socketsandglass

facingupordown.

Please decide how you

wouldlikethexture

tobehungandfollow

thecorresponding

instructions.

2. ASSEMBLING THE FIXTURE

Determinewhetheryouwouldlikethesocketsandglasstobemountedfacingupordown.

Ifyouwouldliketheglasstofaceup,turnxtureframe(R)sothatrings(S)sitclosetothetopoftheframeandthesocketsarepointedup.

Gently placethextureonaatsurface.

Ifyouwouldliketheglasstofacedown,turnxtureframe(R)sothatrings(S)sitclosetothebottomoftheframeandthesocketsarepointed

down.Oneof rods(P)hasthe xture’swriesrunning throughit.Youwill also needtoadjustthe xture’swiresto createenough slack to

maneuvertherodthroughtheframetochangetheorientation.Gently placethextureonaatsurface.

Toploop(L)maybeonthexture’swires,butnotthreadedontothexture’sframeatpost(M)ofplate(T).Ifitisnotconnected,pullthexture’s

wiresthroughtoploop(L)beforetwistingtoploop(L)ontopost(M).Bymeasuring,determinethecorrectnumberofchainlinksneededfor

properhangingheight.Ifnecessary,useapairofplierstoopenandremoveanyexcesschain.Attachchainconnectors(K)toeachendof

chain(J)beforeattachingoneendofthechainconnector/chaintotoploop(L).Closethechainconnector.Connecttheotherchainconnector

(K) to canopy loop (H).

Haveanassistantholdthetoploopassembly.Attachoneendofrods(P)torings(S)ofthextureframe.Thenattachthefreeendofrods(P)

to plate (M).

Feedthexture’swiresupthroughtoploop(L)thenthroughchain(J)(everythreelinksorso).Slidecanopyloopcollar(I)andcanopy(G)onto

thechain/wire.

3. CONNECTING THE WIRES

Haveanassistant support the weightofthexturewhilecompletingthe wiring. Cut awayexcesswire.Threadthe xture’s wiresthrough

canopyloop(H)andnipple(F).Attachthexture’swirestothepowersupplywiresfromthejunctionbox.Connectblacktoblack(orsmooth);

whitetowhite(orribbed);groundtoground(greenorcopper).Twisttheendsofthewirepairstogether,andthentwistonawireconnector.

Makesurealltwistsareinthesamedirection.Ifthereisnogroundwire(greenorcopper)comingfromthejunctionbox,locategroundscrew

(E)onmountingstrap(A)andwrapthexture’sgroundwirearoundthegreengroundscrew(E).Useascrewdrivertosecuregroundscrew(E)

ontothemountingbracket.Tuckallwiresneatlyintothejunctionbox.

4. FINISHING THE INSTALLATION

Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)ontocanopyloop

(H) to secure canopy (G) in place.

Slideglassshades(N)oversockets(Q)andsecureinplacewithsocketrings(O).Installlightbulbs(notprovided)inaccordancewiththe

xture’sspecications.Donotexceedthemaximumrecommendedwattage.

Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.

DOWN - INSTALLATION

Golden Lighting 4855-3 RBZ-SD Installation guide

Brand: Golden Lighting

Model: 4855-3 RBZ-SD

Type: Installation guide

This manual is also suitable for

Download PDF

report

Golden Lighting 4855-3 RBZ-SD Installation guide

This manual is also suitable for

Golden Lighting 4855-3 RBZ-SD Installation guide

Related papers

Other documents