H3C MSR 30-16 Installation guide

H3C MSR 30 Series Routers

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08047L-20081106-C-1.03

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Organization

MSR 30 Series Routers Installation Manual is organized as follows:

Chapter Contents

1 Overview

Briefly introduces the appearance, system description, as well as

the features and applications of the MSR 30 series.

2 Installation Preparation

Describes the requirements on installation site, the safety

recommendations before and during installation, and the required

tools.

3. Installation

Covers the procedures for installing the MSR 30 series, power cord

connection, AUX cable connection, Console cable connection,

Ethernet cable connection and Synchronous/asynchronous serial

interface cable connection.

4. Startup and Configuration

Helps you get familiar with the basic knowledge of how to boot and

configure the MSR 30 series, including device startup, power-on,

and initialization of system files, and so on.

5. Software Maintenance

Introduces how to maintain BootROM menu and software of the

MSR 30 series.

6. Hardware Maintenance

Introduces how to install and remove SDRAM, ESM/VCPM card

and CF card of the MSR 30 series.

7. Troubleshooting Describes some problems that may arise and how to solve them.

Conventions

The manual uses the following conventions:

Command conventions

Convention Description

Boldface

The keywords of a command line are in Boldface.

italic

Command arguments are in italic.

[ ] Items (keywords or arguments) in square brackets [ ] are optional.

{ x | y | ... }

Alternative items are grouped in braces and separated by vertical bars.

One is selected.

[ x | y | ... ]

Optional alternative items are grouped in square brackets and

separated by vertical bars. One or none is selected.

{ x | y | ... } *

Alternative items are grouped in braces and separated by vertical bars.

A minimum of one or a maximum of all can be selected.

[ x | y | ... ] *

Optional alternative items are grouped in square brackets and

separated by vertical bars. Many or none can be selected.

&<1-n>

The argument(s) before the ampersand (&) sign can be entered 1 to n

times.

# A line starting with the # sign is comments.

GUI conventions

Convention Description

< > Button names are inside angle brackets. For example, click <OK>.

[ ]

Window names, menu items, data table and field names are inside

square brackets. For example, pop up the [New User] window.

/

Multi-level menus are separated by forward slashes. For example,

[File/Create/Folder].

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause

bodily injury.

Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Means a complementary description.

Related Documentation

In addition to this manual, each MSR Series Routers documentation set includes the following:

Manual Description

MSR Series Routers User

Manual

It is a guide for the user to perform the operations correctly. It is

organized into the parts of getting started, system management,

interface, link layer protocol, network protocol, routing protocol,

multicast protocol, security, VPN, reliability, QoS, dial-up and VoIP,

as well as acronyms used in the manual.

It gives the user a detailed description of the operating commands.

It is organized into the parts of getting started, system

management, interface, link layer protocol, network protocol,

routing protocol, multicast protocol, security, VPN, reliability, QoS,

dial-up and VoIP, as well as a command index.

MSR Series Routers Interface

Card and Interface Module

Manual

It covers the pinouts, function, interface attributes, panels and

LEDs of all interface cards and modules available with the router.

MSR 20-1X Series Routers

Installation Manual

This guide describes the MSR 20-1X Series Routers and how to

install hardware, configure and boot software, and maintain

software and hardware. This guide also provides troubleshooting

and support information for your router.

MSR 20 Series Routers

Installation Manual

This guide describes the MSR 20 Series Routers and how to install

hardware, configure and boot software, and maintain software and

hardware. This guide also provides troubleshooting and support

information for your router.

MSR 50 Series Routers

Installation Manual

This guide describes the MSR 50 Series Routers and how to install

hardware, configure and boot software, and maintain software and

hardware. This guide also provides troubleshooting and support

information for your router.

MSR 20-1x Series Routers

Web-Based Configuration

Manual

It provides guidelines to Web-based configuration on the MSR

20-1x Series Routers.

MSR 20/30/50 Series Routers

Web-Based Configuration

Manual

It provides guidelines to Web-based configuration on the MSR

20/30/50 Series Routers.

Obtaining Documentation

You can access the most up-to-date H3C product documentation on the World Wide Web at this URL:

http://www.h3c.com.

The following are the columns from which you can obtain different categories of product documentation:

[Products & Solutions]: Provides information about products and technologies, as well as solutions.:

Provides information about products and technologies.

[Technical Support & Document > Technical Documents]: Provides several categories of product

documentation, such as installation, operation, and maintenance.

[Technical Support & Document > Product Support > Software]: Provides the documentation released

with the software version.

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the

proper storage, use and disposal of this product, national laws and regulations must be observed.

1

Table of Contents

1 Overview.....................................................................................................................................................1-1

Introduction .............................................................................................................................................1-1

System Description.................................................................................................................................1-1

Fixed Interfaces...............................................................................................................................1-1

Interface Cards................................................................................................................................1-2

Processor and Memory...................................................................................................................1-2

Other Hardware Specifications........................................................................................................1-3

MSR 30-11 Router...........................................................................................................................1-3

MSR 30-16 Router...........................................................................................................................1-4

MSR 30-20 Router...........................................................................................................................1-6

MSR 30-40 Router...........................................................................................................................1-8

MSR 30-60 Router.........................................................................................................................1-10

Generic Modules...................................................................................................................................1-12

SIC/DSIC Cards ............................................................................................................................1-12

MIM/DMIM Cards ..........................................................................................................................1-13

ESM...............................................................................................................................................1-13

VPM/VCPM ...................................................................................................................................1-13

2 Installation Preparations...........................................................................................................................2-1

Requirements on Environment ...............................................................................................................2-1

Requirements on Temperature/Humidity ........................................................................................2-1

Requirements on Cleanness...........................................................................................................2-1

Requirements on Electrostatic Discharge Prevention.....................................................................2-2

Requirements on Electromagnetic Environments...........................................................................2-2

Requirements on Preventing Lightning...........................................................................................2-2

Requirements on Workbench..........................................................................................................2-3

Safety Precautions..................................................................................................................................2-3

Installation Tools, Meters and Equipments.............................................................................................2-3

3 Installation..................................................................................................................................................3-1

Installation Process.................................................................................................................................3-1

Installing Cabinets...................................................................................................................................3-2

Installing the Router................................................................................................................................3-2

Installing the Router on a Workbench.............................................................................................3-2

Installing the Router in a Rack ........................................................................................................3-2

Installing Generic Modules......................................................................................................................3-3

Connecting the PGND.............................................................................................................................3-4

Connecting the Power Cord....................................................................................................................3-4

Power Input and PGND...................................................................................................................3-5

Connecting the AC Power Cord......................................................................................................3-5

Connecting the DC Power Cord......................................................................................................3-5

Connecting the RPS Power Cord....................................................................................................3-7

Connecting the Console Terminal...........................................................................................................3-8

Fixed Interfaces.......................................................................................................................................3-9

Ethernet Interface............................................................................................................................3-9

2

Connecting AUX to a Modem........................................................................................................3-11

Interface Card Module...........................................................................................................................3-12

Slide Rail Installation on MSR 30-16/30-20 and Removal....................................................................3-12

Slide Rails......................................................................................................................................3-12

Installing the Slide .........................................................................................................................3-13

Uninstalling the Slide Rail..............................................................................................................3-13

Slide Rail Installation on MSR 30-40/30-60 and Removal....................................................................3-14

Slide Rails......................................................................................................................................3-14

Installing the Slide Rail..................................................................................................................3-15

Uninstalling the Slide Rail..............................................................................................................3-16

Verifying Installation..............................................................................................................................3-17

4 Startup and Configuration ........................................................................................................................4-1

Startup.....................................................................................................................................................4-1

Setting up Configuration Environment.............................................................................................4-1

Powering on the Router...................................................................................................................4-3

Startup Process...............................................................................................................................4-4

Configuration Fundamentals...................................................................................................................4-6

Basic Configuration Procedures......................................................................................................4-6

Command Line Interface.................................................................................................................4-6

Arranging Slots and Numbering Interfaces .....................................................................................4-7

5 Software Maintenance...............................................................................................................................5-1

Introduction .............................................................................................................................................5-1

Files.................................................................................................................................................5-1

Software Maintenance Methods......................................................................................................5-3

BootROM Menu ......................................................................................................................................5-4

Main BootROM Menu......................................................................................................................5-4

BootROM Submenus.......................................................................................................................5-6

Upgrading BootROM Through Serial Port ..............................................................................................5-8

Modifying Serial Port Parameters....................................................................................................5-9

Upgrading BootROM.....................................................................................................................5-10

Upgrading Application Program Through Serial Port............................................................................5-12

Upgrading Application Program Through Ethernet Interface................................................................5-12

Configuring Ethernet Parameters..................................................................................................5-12

Upgrading Application Program Through Ethernet Interface........................................................5-14

Maintaining Application Program and Configurations Through Command Lines.................................5-16

Maintaining the Router with TFTP Server.....................................................................................5-16

Maintaining the Router with FTP Server .......................................................................................5-18

Maintaining Application Program and Configuration File......................................................................5-21

Dealing with Router Password Loss.....................................................................................................5-24

User Password Loss......................................................................................................................5-24

BootROM Password Loss .............................................................................................................5-25

Super Password Loss....................................................................................................................5-25

Backing up and Restoring BootROM....................................................................................................5-25

6 Hardware Maintenance..............................................................................................................................6-1

Preparing Tools.......................................................................................................................................6-1

Opening/Closing the Chassis Cover.......................................................................................................6-1

Internal Structure of the Router...............................................................................................................6-3

3

Removing/Installing a Power Module......................................................................................................6-6

Installing/Removing a CF Card...............................................................................................................6-8

Structure..........................................................................................................................................6-8

Installing CF Card............................................................................................................................6-8

Removing CF Card..........................................................................................................................6-8

Replacing a Memory Module..................................................................................................................6-9

Memory Module Structure.............................................................................................................6-10

Memory Module Slot......................................................................................................................6-10

Installing/Removing a Memory Module.........................................................................................6-11

Replacing a VPM ..................................................................................................................................6-13

VPM Structure...............................................................................................................................6-13

VPM Slot........................................................................................................................................6-13

Installing/Removing a VPM...........................................................................................................6-13

Installing/Removing an ESM/VCPM Card.............................................................................................6-14

7 Troubleshooting.........................................................................................................................................7-1

Troubleshooting the Power System........................................................................................................7-1

Troubleshooting the Configuration System.............................................................................................7-1

Troubleshooting Application Image Upgrade..........................................................................................7-2

i

Table of Contents

1 Overview·····················································································································································1-1

Introduction ·············································································································································1-1

System Description·································································································································1-1

Fixed Interfaces·······························································································································1-1

Interface Cards································································································································1-2

Processor and Memory···················································································································1-2

Other Hardware Specifications········································································································1-3

MSR 30-11 Router···························································································································1-3

MSR 30-16 Router···························································································································1-4

MSR 30-20 Router···························································································································1-6

MSR 30-40 Router···························································································································1-8

MSR 30-60 Router·························································································································1-10

Generic Modules···································································································································1-12

SIC/DSIC Cards ····························································································································1-12

MIM/DMIM Cards ··························································································································1-13

ESM···············································································································································1-13

VPM/VCPM ···································································································································1-13

1-1

1 Overview

Introduction

MSR 30 Series Routers were self-developed by our company. for use on enterprise-level networks.

Depending on the network size, MSR 30 Series Routers can be either core routers on small and

medium enterprise networks, or access routers for network branches on some large-sized enterprise

networks. Therefore, MSR 30 Series Routers are suitable for the application on the carrier-level

networks, such as telecom management networks and billing networks. MSR 30 Series Routers adopt

modular design and support a wide range of optional smart interface cards (SICs) and multi-function

interface modules (MIMs). The MSR 30-16 can adopt AC and PoE, and the MSR 30-20, 30-40 and

30-60 can adopt AC, DC, and PoE.

Except the MSR 30-11 and the AC-powered MSR 30-16, the MSR 30 series routers each provide a

redundancy power system (RPS) interface to enhance the routers’ reliability. The PoE-powered routers

can remotely supply power to its powered devices (PDs).

MSR 30 series include these models:

z MSR 30-11

z MSR 30-16

z MSR 30-20

z MSR 30-40

z MSR 30-60

System Description

Fixed Interfaces

Table 1-1 Fixed interfaces of the MSR 30 series routers

Item MSR 30-11 MSR 30-16 MSR 30-20 MSR 30-40 MSR 30-60

Console

1 1 1

1

AUX

1 1 1

1

USB

0 1 2

2

FE

2 2 0

0

GE

0 0

Two

electrical

interfaces

Two

Combo

interfaces

Two

Combo

interfaces

Fixed interfaces

SA 1 0 0 0 0

1-2

Interface Cards

Table 1-2 Interface cards of the MSR 30 series routers

Item MSR 30-11 MSR 30-16 MSR 30-20 MSR 30-40 MSR 30-60

SIC 2 4 4 4 4

MIM 1 1 2 6 6

External

cards

1 0 0 0 0

ESM 1 2 2 2 2

VCPM 0 1 1 1 1

Internal

cards

VPM 0 2 2 3 3

The height of MIM cards may be one U (44.45 mm or 1.75 in.) or half a U. Slot 5 and slot 6 on the MSR

30-20, MSR 30-40, or MSR 30-60 are both half a U high. The two slots together can accommodate only

one 1-U-high MIM card.

Processor and Memory

Table 1-3 Processor and memory of the MSR 30 series routers

Item MSR 30-11 MSR 30-16 MSR 30-20 MSR 30-40 MSR 30-60

Processor PowerPC PowerPC PowerPC PowerPC PowerPC

Boot ROM 2 MB 4 MB 4 MB 4 MB 4 MB

Memory DDR: 256 MB

DDR SDRAM:

256 MB

(default), 768

MB

(maximum)

DDR SDRAM:

256 MB

(default), 1 GB

(maximum)

DDR SDRAM:

256 MB

(default), 1 GB

(maximum)

DDR SDRAM:

256 MB

(default), 1 GB

(maximum)

CF CARD Not supported

256 MB

(default), 1 GB

(maximum)

256 MB

(default), 1 GB

(maximum)

256 MB

(default), 1 GB

(maximum)

256 MB

(default), 1 GB

(maximum)

z Boot ROM stores bootstrap.

z The memory is used to store the communication data between the system and the CPU when the

system is running.

z The CF card is used to store the software system and configuration file. The CF card LED blinks

when the system is reading/writing data from/to the CF card. In this case, do not remove the CF

card, otherwise hardware and software damage may occur.

1-3

Other Hardware Specifications

Table 1-4 Hardware specifications for the MSR 30 series routers

Item MSR 30-11 MSR 30-16 MSR 30-20 MSR 30-40 MSR 30-60

Dimensions (H

× W × D),

excluding feet

and mounting

ears

44.2 × 442 ×

360 mm (1.74

× 17.4 × 14.17

in.)

44.2 × 442 ×

441.8 mm

(1.74 × 17.4 ×

17.39 in.)

44.2 × 442 ×

441.8 mm

(1.74 × 17.4 ×

17.39 in.)

88.2 × 442 ×

422.3 mm

(3.47 × 17.4 ×

16.62 in.)

132 × 442 ×

421.8 mm

(5.20 × 174 ×

16.61 in.)

Weight 4.3 kg (9.5 lb) 6 kg (13.2 lb)

6.9 kg (15.2

lb)

11.9 kg (26.2

lb)

13.6 kg (30 lb)

AC input

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

DC input Not supported Not supported

Rated voltage

range: –48

VDC to –60

VDC

Rated voltage

range: –48

VDC to –60

VDC

Rated voltage

range: –48

VDC to –60

VDC

PoE input Not supported

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Rated voltage

range: 100

VAC to 240

VAC, 50 Hz or

60 Hz

Operating

temperature

0°C to 40°C

(32°F to

104°F)

0°C to 40°C

(32°F to

104°F)

0°C to 40°C

(32°F to

104°F)

0°C to 40°C

(32°F to

104°F)

0°C to 40°C

(32°F to

104°F)

Relative

humidity

(noncondensi

ng)

5% to 90% 5% to 90% 5% to 90% 5% to 90% 5% to 90%

MSR 30-11 Router

Appearance

1) Front view

Figure 1-1 Front panel of the MSR 30-11

(1)(2)(3)

(4)

(5)

(1) Power LED (PWR) (2) System LED (SYS)

(3) ESM LED (4) Power switch

(5) Power receptacle

2) Rear panel

1-4

Figure 1-2 Rear panel of the MSR 30-11

(2) (3)(1) (4) (5) (6) (8)(7)

(9)(10)

(1) Grounding terminal (2) FE interface 1

(3) FE interface 0 (4) Console/AUX interface

(5) Serial interface (6) Serial interface status LEDs

(7) MIM/XMIM slot (8) Removable slide rails

(9) SIC slot 1 (10) SIC slot 2

Panel LEDs

Table 1-5 LEDs on the front panel of the MSR 30-11

LED Description

PWR

ON: The power supply of the system works normally.

OFF: The power supply of the system is disconnected.

SYS

Blinking: The system runs normally.

ON or OFF: The system runs abnormally.

ESM

OFF: No ESM is in position.

Solid green: An ESM is in position and works normally.

Blinking green: The ESM is processing data.

Solid yellow: An ESM is in position but is faulty.

Table 1-6 LEDs on the rear panel of the MSR 30-11

LED Description

LINK

OFF: No link is present.

ON: A link is present.

ACT

OFF: No data is being received or sent.

Blinking: Data is being received or sent.

MSR 30-16 Router

Appearance

1) Front view

1-5

Figure 1-3 Front view of MSR 30-16

(1)

(2)

(3)

(4)(5)(6)(7) (8)(9)

(1) Power LED (POWER) (2) System LED (SYSTEM)

(3) Console port (CONSOLE) (4) Auxiliary port (AUX)

(5) USB interface (6) CF card

(7) CF card LED (8) Power socket

(9) Power switch

2) Rear view

Figure 1-4 Rear view of MSR 30-16

(1) FE interface 0 (2) FE interface 1

(3) ESM1 LED (4) ESM0 LED

(5) VPM1 LED (6) VPM0 LED

(7) VCPM LED (8) Grounding terminal

(9) SIC slot 1 (10) SIC slot 2

(11) SIC slot 3 (12) SIC slot 4

(13) MIM slot 5

Panel LEDs

Table 1-7 Front panel LEDs description of MSR 30-16 router

LED Description

PWR

ON means: the system provides power for cards normally.

OFF means the system does not supply power for cards.

SYS

Blinking means the system is operating normally.

Steady ON or steady OFF means the system does not operate normally.

USB0

OFF means the USB interface has not been connected to a host.

Steady green means the USB interface is connected to a host and the host can be

removed.

Blinking green means data is being transferred to/from the host and the host cannot

be removed now.

1-6

LED Description

CF

CF card LED:

Steady green means the CF card is in place and can be identified by the router.

Blinking green means the CF card is being accessed and must not be removed.

Steady yellow means the CF card is in place but cannot be identified by the router.

OFF means no CF card is inserted or the CF card cannot be identified.

Table 1-8 Rear panel LEDs of MSR 30-16 Router

LED Description

LINK

OFF means no link is present.

ON means a link connection is established.

ACT

OFF means no data is being received or sent.

ON means data is being received or sent.

ESM0 to 1

OFF means no ESM is in the ESM slot.

Solid green means an ESM is in the ESM slot and operates normally.

Blinking green means the ESM is processing data.

Solid yellow means an ESM is in the ESM slot but does not operate normally.

VCPM

OFF means VCPM is not in the slot.

Steady green means a VCPM is in the slot and operates normally.

Steady yellow means a VCPM is in the slot but does not operate normally.

VPM0 to 1

OFF means no VPM is in the VPMx slot.

Steady green means a VPM is in the VPMx slot and operates normally.

Steady yellow means a VPM is in the VPMx slot but does not operate normally.

MSR 30-20 Router

Appearance

1) Front view

Figure 1-5 Front view of MSR 30-20

(1) Power LED (PWR) (2) System LED (SYS)

(3) USB LED (4) Console port (CONSOLE)

(5) Auxiliary port (AUX) (6) USB interface 0

(7) USB interface 1 (8) CF card LED

(9) CF card (10) Power socket

(11) Power switch

1-7

2) Rear view

Figure 1-6 Rear view of MSR 30-20

(1)

(2) (6)

(4) (3)

(5)

(7)

(8)

(12)(11)(10)

(13)(14)(9)

(1) GE interface 0 (2) GE interface 1

(3) SIC slot 1 (4) SIC slot 2

(5) SIC slot 3 (6) SIC slot 4

(7) MIM slot 5 (8) MIM slot 6

(9) Grounding terminal (10) VCPM LED

(11) VPM1 LED (12) VPM0 LED

(13) ESM0 LED (14) ESM1 LED

Panel LEDs

Table 1-9 Front panel LEDs description of MSR 30-20 router

LED Description

PWR

Power LED:

ON means the system provides power for cards normally.

OFF means the system does not supply power for cards.

SYS

Hardware system operation LED:

Blinking means the system is operating normally.

Steady ON or steady OFF means the system does not operate normally.

USB0

OFF means the USB interface has not been connected to a host.

Steady green means the USB interface is connected to a host and the host can be

removed.

Blinking green means data is being transferred to/from the host and the host cannot

be removed now.

CF

CF card LED:

Steady green means the CF card is in the slot and can be identified by the router.

Blinking green means the CF card is being accessed and cannot be removed.

Steady yellow means the CF card is in the slot but cannot be identified by the router.

OFF means no CF card is inserted or the CF card cannot be identified.

Table 1-10 Rear panel LEDs of MSR 30-20 Router

LED Description

GE LED

OFF means no link is present.

Steady green means a 1000 Mbps connection has been established.

Blinking green means data is being received or transmitted at a speed of 1000 Mbps.

Steady yellow means a 10/100 Mbps connection has been established.

Blinking yellow means data is being received and transmitted at a speed of 10/100

Mbps.

1-8

LED Description

ESM0 to 1

OFF means no ESM is in the ESM slot.

Steady green means an ESM is in the ESM slot and operates normally.

Blinking green means the ESM is processing data.

Steady yellow means an ESM is in the ESM slot but does not operate normally.

VCPM

OFF means no VCPM is in the slot.

Steady green means a VCPM is in the slot and operates normally.

Steady yellow means a VCPM is in the slot but does not operate normally.

VPM0 to 1

OFF means no VPM is in the VPMx slot.

Steady green means a VPM is in the VPM slot and operates normally.

Steady yellow means a VPM is in the VPM slot but does not operate normally.

MSR 30-40 Router

Appearance

1) Front view

Figure 1-7 Front view of MSR 30-40

(2)(3)

(10)

(8)

(9)

(6) (5)

(7) (4) (1)

(11)

(1) Power LED (PWR) (2) System LED (SYS)

(3) USB LED (4) Console port (CONSOLE)

(5) Auxiliary port (AUX) (6) USB interface 0

(7) USB interface 1 (8) CF card LED

(9) CF card (10) Power socket

(11) Power switch

2) Rear view

1-9

Figure 1-8 Rear view of MSR 30-40

(9)

(4) (8)

(3) (7)

(2) (6)

(1) (5)

(11)

(10)(12)

(14) (13)(16) (17)(15) (18)

(19)

(20)(21)

(1) VCPM LED (2) VCPM0 LED

(3) VPM1 LED (4) VPM2 LED

(5) SFP0 LED (6) SFP1 LED

(7) ESM0 LED (8) ESM1 LED

(9) GE0 port (10) GE1 port

(11) SFP0 port (12) SFP1 port

(13) SIC slot 1 (14) SIC slot 2

(15) SIC slot 3 (16) SIC slot 4

(17) MIM slot 5 (18) MIM slot 6

(19) MIM slot (20) MIM slot 8

(21) Grounding terminal

Panel LEDs

Table 1-11 Front panel LEDs description of MSR 30-40 router

LED Description

PWR

Power LED:

ON means the system provides power for cards normally.

OFF means the system does not supply power for cards.

SYS

Hardware system operation LED

Blinking means the system is operating normally.

Steady ON or steady OFF means the system does not operate normally.

USB0

OFF means the USB interface is not connected to a host;

Steady green means the USB interface has been connected to a host and the host

can be removed.

Blinking green means data is being transferred to/from the host and the host cannot

be removed now.

CF

CF card LED

Steady green means the CF card is in the slot and can be identified by the router.

Blinking green means the CF card is being accessed and cannot be removed.

Steady yellow means the CF card is in the slot but cannot be identified by the router.

OFF means no CF card is inserted or the CF card cannot be identified.

1-10

Table 1-12 Rear panel LEDs of MSR 30-40 Router

LED Description

GE LED

OFF means no link is present.

Steady green means a 1000 Mbps connection has been established.

Blinking green means data is being received or transmitted at a speed of 1000 Mbps.

Steady yellow means a 10/100 Mbps connection has been established.

Blinking yellow means data is being transmitted at a speed of 10/100 Mbps.

SFP0 to 1

OFF means no SFP connection is established.

Steady green means SFP connection has been established.

Blinking green means SFP is receiving or transmitting data.

Steady yellow means SFP cannot be identified by the router.

ESM0 to 1

OFF means no ESM is in the ESM slot.

Steady green means an ESM is in the ESM slot and operates normally.

Blinking green means the ESM is processing data.

Solid yellow means an ESM is in the ESM slot but does not operate normally.

VCPM

OFF means no VCPM is in the slot.

Steady green means a VCPM is in the slot and operates normally.

Steady yellow means a VCPM is in the slot but does not operate normally.

VPM0 to 2

OFF means no VPM is in the VPMx slot.

Steady green means a VPM is in the VPMx slot and operates normally.

Steady yellow means a VPM is in the VPMx slot but does not operate normally.

MSR 30-60 Router

Appearance

1) Front view

Figure 1-9 Front view of MSR 30-60

(3)(2)

(1)(4)

(5)(6)

(7)

(10)(8) (9) (11)

(1) Power LED (PWR) (2) System LED (SYS)

(3) USB LED (4) Console port (CON)

(5) Auxiliary port (AUX) (6) USB interface 0

(7) USB interface 1 (8) CF card LED

(9) CF card (10) Power socket

(11) Power switch

Page is loading ...

H3C MSR 30-16 Installation guide

This manual is also suitable for

H3C MSR 30-16 Installation guide

Related papers

Other documents