Hitachi PJTX10WAU User manual

Category
Data projectors
Type
User manual

This manual is also suitable for

ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
TECHNICAL
Projector
PJTX10
PJTX10W/PJTX10E/PJTX10WAU
User’s Manual – Operating Guide
Please read this users manual thoroughly to ensure correct usage understanding.
Manuel d’utilisation – Guide d'utilisation
N
ous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement
de l’appareil.
Bedienungsanleitung – Benutzerhandbuch
Um zu gewährleisten, dass Sie die Bedienung des Geräts verstanden haben, lesen Sie dieses
Handbuch bitte sorgfältig.
Manual de usuario – Guía de funcionamiento
Lea atentamente el manual de usuario del proyector para garantizar un uso adecuado del mismo.
Manuale d'istruzioni – Guida operativa
Vi preghiamo di leggere attentamente il manuale d'istruzioni per garantire una corretta
comprensione delle istruzioni.
TECHNICAL
1
Projector
PJ-TX10
PJ-TX10
PJ-TX10W / PJ-TX10E / PJ-TX10W(AU)
PJ-TX10W / PJ-TX10E / PJ-TX10W(AU)
User
User
s Manual – Quick Guide
s Manual – Quick Guide
Thank you for purchasing this projector.
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual.
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
NOTE
Your projector should come with the items shown below. Contact your dealer if anything is missing.
Keep the original packing material for future reshipment. For moving the projector, be sure to use the
original packing material. Use special caution for the lens part.
WARNING Before using, read the "User's Manual - Safety Guide" and
these manuals to ensure correct usage through understanding. After reading,
store them in a safe place for future reference.
User’s manuals (4)
SEARCH
SRC
VIDEO
VSVC
WIDEAUTO
MUTE
BLANK
CUSTOM
CINEMA
AT
CIN
M1
E
DYNAMIC
DYN
ENT
MYMEMORY
NORMAL
NOR CUS
WID
PC
MENU
ENTER
ESC RESET
VOLUME
COMPUTER
COMPONENTS-VIDEO
OFF
ON
KEYSTONE
M2 M3 M4
Remote control &
AA batteries (2)
Contents Of Package
Contents Of Package
Refer to this table, in case of 16:9 aspect ratios.
The values (a) and (b) shown in the table are
calculated for a full size screen: 854x480.
Arrangement
Arrangement
(±10%)
Rivet & Strap
Projector
(with Lens Cap)
Video/Audio
cable
SCART adapter
(PJ-TX10E only)
Power cords
PJ-TX10W (3):
US, UK, Europe
PJ-TX10E (2):
UK, Europe
PJ-TX10W(AU) (1):
Australia
(a)
(b)
Screen
Side View
Screen
size
Screen Size [inch (m)]
(a) [inch (m)]
(b)
[inch (cm)]
Min. Max.
30 (0.8) 29(0.7) 60(1.5) 15(37)
40 (1.0) 40(1.0) 81(2.1) 20(50)
50 (1.3) 50(1.3) 102(2.6) 25(62)
60 (1.5) 60(1.5) 122(3.1) 29(75)
70 (1.8) 71(1.8) 143(3.6) 34(87)
80 (2.0) 81(2.1) 163(4.2) 39(100)
90 (2.3) 91(2.3) 184(4.7) 44(112)
100 (2.5) 101(2.6) 205(5.2) 49(125)
200 (5.1) 204(5.2)
411(10.4)
98(249)
300 (7.6) 307(7.8)
616(15.7)
147(374)
2
Connecting Devices
Connecting Devices
Please refer to the following for connecting your devices.
See the rear of the projector and open the ports cover.
You can see the ports.
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
Connecting to a computer
RGB out RGB cable (D-sub 15 pin)
Audio out Audio cable (Stereo mini)
RS-232C port RS-232C cable
Connecting to a DVD/VCR player
Video out
Audio out (L) Audio/Video cable
Audio out (R)
If using a SCART RGB input,
Video
AUDIO-L
AUDIO-R SCART SCART cable
G out port
B
R
If using a S-video input,
S-video out port S-video cable
Audio out (L) Audio cable
Audio out (R)
If using a component input,
Component (Y) out
Component (CB/PB) out Component cable
Component (CR/PR) out
Audio out (L) Audio cable
Audio out (R)
If using a component input from
COMPUTER port,
Component (Y) out
Component (CB/PB) out Component cable
Component (C
R/PR) out (with D-sub 15 pin)
Audio out Audio cable(Stereo mini)
Power switch
3
1
Connect the connector of the power cord to the AC
inlet of the projector.
2
Firmly plug the power cord’s plug into the outlet.
1
Remove the lens cap.
2
Set the power switch to [ | ] (ON).
3
Press the STANDBY/ON button of the
projector or the ON button of the
remote control.
The projector lamp will light up and the
POWER indicator will begin blinking green.
According to a setup, the projector lamp
may light up and the POWER indicator
may begin blinking green, without
pressing this button.
When the power is completely on, the
indicator will stop blinking and light green.
The POWER indicator will light orange.
WARNING
• Please use extra caution when connecting the power cord as incorrect or faulty
connections may result in FIRE and/or ELECTRICAL SHOCK. Please adhere to the “User’s manual – Safety
Guide” and the following.
• Only plug the power cord into outlets rated for use with the power cord’s specified voltage range.
• Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get
correct one.
• Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug.
• Make sure that you firmly connect the power cord to the projector and wall outlet.
WARNING
• When the power is ON, a strong light is emitted. Do not look into the lens or vents of
the projector.
Connecting Power Supply
Connecting Power Supply
T
T
urning On/Of
urning On/Of
f Power
f Power
Turning ON The Power
Turning OFF The Power
Power switch (ON position)
1
Press the STANDBY/ON button of the
projector or the OFF button of the remote
control.
The message “Power off?” will appear on
the screen for approximately 5 seconds.
4
Attached the lens cap.
2
Press the STANDBY/ON button again
while “Power off?” the message is
visible.
The projector lamp will go off, and the
POWER indicator will begin blanking orange.
Then the POWER indicator will stop
blinking and light to solid orange when the
lamp cooling is complete.
3
Switch the power switch to [O] (OFF).
The POWER indicator will go off.
Power switch (OFF position)
STANDBY/ON
INPUT
POWER
LAMP
TEMP
MENU
STANDBY/ON button
POWER indicator
AC Inlet
Connector Side
Power cord
4
Adjusting The Projector's Elevator
Using The Picture Shift Dials
CAUTION
To prevent damaging the projector and injuring yourself, ALWAYS
HOLD THE PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
You can use the elevator feet to adjust the angle of projection. The adjustment range of
the elevator feet is 0 to 9 degrees.
Press and hold in the elevator buttons.
2
Raise or lower the projector to the desired
height and then release the elevator buttons.
When you release the elevator buttons, the elevator feet will
lock into position.
3
As necessary, you can also finely adjust the
height of the projector by twisting the
elevator feet by hand.
Selecting An Input Signal
1
2
Use the zoom ring to adjust the screen
size.
Press the INPUT button.
As illustrated below, each time you press the INPUT
button, the projector switches between its input signal
ports. Select the signal you wish to project.
COMPUTER VIDEO S-VIDEO
COMPONENT VIDEO
STANDBY/ON
INPUT
POWER
LAMP
TEMP
MENU
INPUT button
Pr
Pr
ojecting The Pictur
ojecting The Pictur
e
e
3
Use the focus ring to focus the picture.
Zoom ring
Focus ring
Elevator buttons
Elevator feet
1
When you want to finely adjust the picture position, use the picture shift dials.
Horizontal picture shift dial
7.5:2.5
to
2.5:7.5
10:0
to
0:10
Vertical picture shift dial
Generally, better quality of a picture is available when the lens shift is set to the center.
Do not attach anything other than specified options (such as an optional conversion lens) to the
screw thread. For details, please ask your dealer.
NOTE
5
See the top of the projector. You can see the control buttons.
Contr
Contr
ol Buttons
ol Buttons
Pr
Pr
eparing Remote Contr
eparing Remote Contr
ol
ol
POWER indicator
tells the state of power
supply. Refer to the section
Turning On/Off Power.
INPUT button
toggles between
the signal ports.
MENU buttons
operate the menu function.
STANDBY/ON button
prepares for turning the power on/off. Refer
to the section Turning On/Off Power.
TEMP indicator
lights or blinks when any
problem about internal
temperature has happened.
LAMP indicator
lights or blinks when any
problem about the lamp has
happened.
CAUTION Always handle the batteries with care and use them only as directed.
Improper use may result in battery cracking or leakage, which could result in fire, injury
and/or polution of the surrounding environment.
Keep the battery away from children and pets.
Be sure to use only the batteries specified for use with the remote control. Do not mix
new batteries with used ones.
When inserting batteries, verify that the plus and minus terminals are aligned correctly
(as indicated in the remote control).
When you dispose the battery, you should obey the law in the relative area or country.
COMPUTER VIDEO
S-VIDEO
COMPONENT VIDEO
Putting Batteries Into The Remote Control
1
Remove the
battery cover.
Slide back and
remove the battery
cover in the direction
of the arrow.
Insert the batteries.
Align and insert the two
AA batteries according to
their plus and minus
terminals (as indicated in
the remote control).
Close the battery
cover.
Replace the battery
cover in the direction
of the arrow and
snap it back into
place.
2
3
STANDBY/ON
INPUT
POWER
LAMP
TEMP
MENU
6
See the remote control.
Remote Contr
Remote Contr
ol
ol
OFF button
prepares for turning the
power off.
SEARCH button
searches for an input
signal between the
following signal ports of
COMPUTER, VIDEO,
S-VIDEO and
COMPONENT VIDEO.
MENU button
opens/closes the menu.
S-VIDEO button
selects the input signal
of S-VIDEO port.
COMPONENT
button
selects the input signal of
COMPONENT port.
VOLUME button
turns on/off the VOLUME
mode.
In the VOLUME mode,
To adjust the volume,
use the cursor
/
buttons.
MUTE button
mutes/restores the sound.
BLANK button
blanks the screen
temporarily.
M1, M2, M3, M4
buttons
call the setting data on
each memory.
VIDEO button
selects the input signal of
VIDEO port.
ON button
prepares for turning the
power on.
COMPUTER button
selects the input signal of
COMPUTER port.
WIDE button
toggles between the
modes for aspect ratio.
AUTO button
executes automatic
adjustment.
CINEMA, DYNAMIC,
NORMAL, CUSTOM
buttons
select each of gamma
mode.
KEYSTONE button
turns on/off the KEYSTONE
mode.
In the KEYSTONE mode,
To adjust the
keystone,
use the cursor
/
buttons.
ESC button
returns to the previous
display at the menu
functions.
,,,
(Cursor) buttons
works for adjusting or
menu controlling.
RESET button
cancels the adjustment in
progress.
* The adjustments of the
volume etc. are not reset.
ENTER button
proceeds to the next
operation at the menu
functions.
SEARCH
SRC
VIDEO
VSVC
WIDEAUTO
MUTE
BLANK
CUSTOM
CINEMA
AT
CIN
M1
E
DYNAMIC
DYN
ENT
MYMEMORY
NORMAL
NOR CUS
WID
PC
MENU
ENTER
ESC RESET
VOLUME
COMPUTER
COMPONENTS-VIDEO
OFF
ON
KEYSTONE
M2 M3 M4
After making sure that the projector has cooled adequately,
slowly flip over the projector, so that the bottom is facing up.
7
Lamp
Lamp
WARNING Please carefully read the “User’s Manual - Safety Guide”.
The projector uses a high-pressure mercury glass lamp made of glass. The lamp can
break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of
glass to fly into the lamp housing, and for gas containing mercury to escape from the
projectors vent holes.
Do not open the lamp cover, if the lamp should break, or while the projector is
suspended from above. Ask your dealer to clean the projector or replace the lamp.
Before replacing the lamp, make sure the power switch is off and the power cable is
not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently.
Use the lamp of the specified type only. Type number: DT00611
(sold separately)
CAUTION
Do not reset the lamp timer without replacing the lamp.
Replacing The Lamp
If the indicators or a message prompts you to replace the lamp, replace the lamp
as soon as possible.
1
Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at
least 45 minutes.
2
Contact your local dealer to prepare a new lamp.
Tell the dealer your lamp type number. If the projector is mounted on the ceiling, or if the lamp has
broken, also ask the dealer to replace the lamp.
3
4
Unscrew the screw of the lamp cover, then slide and take
the lamp cover up.
5
Unscrew the 2 screws, and slowly pick up the lamp by the
handles.
6
Insert the new lamp, and tighten the 2 screws firmly to lock
it in place.
7
Slide the lamp cover into place, and tighten the screw of the
lamp cover firmly.
8
Slowly turn the projector so that the top is facing up.
9
Turn on the projector, and reset the lamp timer. When the lamp has been replaced after
the message of "THE POWER WILL TURN OFF AFTER 0hr." is display, complete the
following operation within 10 minutes of switching power on.
(1) While the projector running, press the MENU button to open the menu.
(2)
Choose the OPTION on the menu using the
/
button, then press the button or ENTER button.
(3) Choose the LAMP TIME using the
/
button, then press and hold the button of
projector or the RESET button of remote control for 3 seconds.
(4) Choose the RESET using the button.
In the case of replacement by yourself,
Lamp cover
Screw
Handles
Screws
8
Air Filter
Air Filter
WARNING
Please carefully read the “User’s Manual - Safety Guide”.
If the air filter becomes clogged by dust or the like, internal temperature rises and could cause malfunction.
Use the air filter of the specified type only.Type number: NJ08312
(sold separately)
Do not use the projector with the air filter and filter cover removed.
CAUTION
Do not reset the filter timer without cleaning or replacing the air filter.
When you replace the lamp, please replace also the air filter. The air filter may be attached when you buy a
replacement lamp for this projector. Please ask your dealer.
Caring For The Air Filter
The air filter should be cleaned about every 100 hours. If the indicators or a message prompts you to
clean the air filter, clean the air filter as soon as possible.
Replacing The Air Filter
Turn off the projector, and unplug the power cord.
Apply a vacuum cleaner to the top of the filter cover to clean the air filter.
Reset the filter timer, according to following “Reset The Filter Timer”.
Turn off the projector, and unplug the power cord.
Insert a new air filter, and replace the filter cover.
Reset the filter timer, according to following “Reset The Filter Timer”.
2
Contact your local dealer to prepare a new air filter. Tell the dealer
your air filter type number.
Reset The Filter Timer
Only after cleaning or changing the air filter, the filter timer has to be reset. To reset the filter timer,
1
Turn on the projector. While the projector running, press the MENU button to open the
menu.
2
Choose the “OPTION” on the menu using the
/
button, then press the button
or ENTER button.
3
Choose the “FILTER TIME” using the
/
button, then press and hold the
button of projector or the RESET button of remote control for 3 seconds.
Choose the “RESET” using the button.
3
After making sure that the projector has cooled adequately,
remove the filter cover. Hold the release buttons of the filter
cover, while pulling up it.
Hold the release buttons of the air filter, while pulling down it.
4
1
1
4
5
6
2
3
Filter cover
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced.
Please replace the air filter as soon as possible.
Filter cover
Air filter
Release buttons
Release buttons
Thank you for purchasing this projector.
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual.
• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
TRADEMARK ACKNOWLEDGMENT :
• VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple and Mac are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
NOTE
WARNING Before using, read the "User's Manual - Safety Guide" and
these manuals to ensure correct usage through understanding. After reading,
store them in a safe place for future reference.
Projector
PJTX10
PJTX10W / PJTX10E / PJTX10WAU
User's Manual - Operating Guide
1
Ultra High Brightness
Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly
efficient optical system.
Whisper Mode Equipped
Special mode is available for reducing projector noise to achieve quieter operation.
User Memory Function
This projector can memorize 4 settings by MY MEMORY function.
Optical Lens Shift
The lens of this projector can be shifted horizontally and vertically. When you want to finely adjust the
picture position, use the picture shift dials.
Keystone Distortion Correction
Quick correction of distorted images electrically.
Preparation
Please see the “Contents Of Package” of the “User’s Manual – Quick Guide”.
Your projector should come with the items shown there. Contact your dealer
anything is missing.
Projector Features
This multimedia projector is used to project various computer signals as well as
NTSC / PAL / SECAM video signals onto a screen. Little space is required for
installation and large images can easily be realized.
• Keep the original packing material for future reshipment. For moving the projector, be
sure to use the original packing material. Use special caution for the lens part.
NOTE
2
3
Projector Features 2
Preparation 2
Part Names 4
The Projector 4
Fastening The Lens Cap 4
The Remote Control 6
Setting Up 7
Arrangement 7
Adjusting The Projector’s
Elevator 8
Using The Picture Shift Dials 8
Connecting Your Devices 9
Connecting Power Supply 11
Remote Control 12
Putting Batteries 12
Operating The Remote Control 13
Power ON/OFF 14
Turning On The Power 14
Selecting An Input Signal 15
Turning Off The Power 16
Operating 17
Adjusting The Volume 17
Temporarily Muting The Sound 17
Using The Automatic
Adjustment Feature 18
Correcting Keystone
Distortions 18
Signal Searching 19
Selecting The Aspect Ratio 19
Temporarily Blanking
The Screen 19
Selecting The Gamma Mode 20
Recalling Your Adjustments 20
Multifunctional Settings 21
Using The Menu Functions 21
MAIN Menu 22
PICTURE-1 Menu 23
PICTURE-2 Menu 25
INPUT Menu 26
AUTO Menu 28
SCREEN Menu 29
OPTION Menu 30
Lamp 31
Replacing The Lamp 32
Air Filter 33
Caring For The Air Filter 33
Replacing The Air Filter 34
Other Care 35
Caring For The Inside
Of The Projector 35
Caring For The Lens 35
Caring For The Cabinet
And Remote Control 35
Troubleshooting 36
Related Messages 36
Regarding
The Indicator Lamps 38
Phenomena That May Easily Be
Mistaken For Machine Defects 40
Warranty And After-Service 41
Specifications 42
TECHNICAL
Contents
4
Strap Rivet
Strap
hole
Part Names
The Projector
Zoom ring
Focus ring
Air filter cover
(An air filter is
inside.)
Elevator button
Elevator feet
Indicates the corresponding
reference page
Lens cap
Lens
(The picture is
projected from
here.)
Remote sensor
Picture shift dial
(vertical)
Picture shift dial
(horizontal)
Projector (Front/Right)
Fastening The Lens Cap
To avoid losing, please fasten the lens cap to the projector using the strap.
1
Fix the strap to the strap ring of lens
cap, as the right drawing.
2
Put one piece of the strap into the
groove on rivet, as the right drawing.
3
Push the rivet into the strap hole.
Lens cap Strap ring Strap
Pull
Rivet
Push in
(Bottom side)
5
AC inlet
VIDEO port
Ports cover
AUDIO port
(from a computer)
S-VIDEO port
COMPONENT VIDEO - Y
COMPONENT VIDEO - C
B/PB
COMPONENT VIDEO - CR/PR
AUDIO R port
L port
(from a video equipment)
Power switch
COMPUTER port
CONTROL
port
Projector (Rear/Left)
STANDBY/ON
INPUT
POWER
LAMP
TEMP
MENU
POWER indicator
tells the state of power supply.
Refer to the section Power
ON/OFF.
INPUT button
toggles between the signal
ports.
MENU buttons
operate the menu function.
STANDBY/ON
button
prepares for turning the
power on/off. Refer to the
section Power ON/OFF.
TEMP indicator
lights or blinks when any
problem about internal
temperature has happened.
LAMP indicator
lights or blinks when any
problem about the lamp has
happened.
COMPUTER VIDEO
S-VIDEO
COMPONENT VIDEO
Part Names (continued)
The Projector (continued)
6
The Remote Control
Part Names (continued)
OFF button
prepares for turning the
power off.
SEARCH button
searches for an input
signal between the
following signal ports of
COMPUTER, VIDEO,
S-VIDEO and
COMPONENT VIDEO.
MENU button
opens/closes the menu.
S-VIDEO button
selects the input signal
of S-VIDEO port.
COMPONENT
button
selects the input signal of
COMPONENT port.
VOLUME button
turns on/off the VOLUME
mode.
In the VOLUME mode,
To adjust the volume,
use the cursor
/
buttons.
MUTE button
mutes/restores the sound.
BLANK button
blanks the screen
temporarily.
M1, M2, M3, M4
buttons
call the setting data on
each memory.
VIDEO button
selects the input signal of
VIDEO port.
ON button
prepares for turning the
power on.
COMPUTER button
selects the input signal of
COMPUTER port.
WIDE button
toggles between the
modes for aspect ratio.
AUTO button
executes automatic
adjustment.
CINEMA, DYNAMIC,
NORMAL, CUSTOM
buttons
select each of gamma
mode.
KEYSTONE button
turns on/off the KEYSTONE
mode.
In the KEYSTONE mode,
To adjust the
keystone,
use the cursor
/
buttons.
ESC button
returns to the previous
display at the menu
functions.
,,,
(Cursor) buttons
works for adjusting or
menu controlling.
RESET button
cancels the adjustment in
progress.
* The adjustments of the
volume etc. are not reset.
ENTER button
proceeds to the next
operation at the menu
functions.
SEARCH
SRC
VIDEO
VSVC
WIDEAUTO
MUTE
BLANK
CUSTOM
CINEMA
AT
CIN
M1
E
DYNAMIC
DYN
ENT
MYMEMORY
NORMAL
NOR CUS
WID
PC
MENU
ENTER
ESC RESET
VOLUME
COMPUTER
COMPONENTS-VIDEO
OFF
ON
KEYSTONE
M2 M3 M4
7
Setting Up
Arrangement
WARNING Install the projector in a suitable environment according to
instructions of the Users Manual Safety Guide and this manual.
The power outlet should be close to the projector and easily accessible.
Refer to the illustrations and tables below to determine the screen size and projection
distance.
The values shown in the table are calculated for a full size screen:854 480
(a):Distance from the projector to the screen (±10%)
(b):Distance from the lens center to the top of the screen (±10%)
Screen Size [inch (m)]
(a) [inch (m)]
(b)
[inch (cm)]
Min. Max.
30 (0.8) 29(0.7) 60(1.5) 15(37)
40 (1.0) 40(1.0) 81(2.1) 20(50)
50 (1.3) 50(1.3) 102(2.6) 25(62)
60 (1.5) 60(1.5) 122(3.1) 29(75)
70 (1.8) 71(1.8) 143(3.6) 34(87)
80 (2.0) 81(2.1) 163(4.2) 39(100)
90 (2.3) 91(2.3) 184(4.7) 44(112)
100 (2.5) 101(2.6) 205(5.2) 49(125)
120 (3.0) 122(3.1) 246(6.2) 59(149)
150 (3.8) 153(3.9) 308(7.8) 74(187)
200 (5.1) 204(5.2)
411(10.4)
98(249)
250 (6.4) 256(6.5)
513(13.0)
123(311)
300 (7.6) 307(7.8)
616(15.7)
147(374)
(a)
(b)
Screen
Reference for
the 16:9 aspect ratio
Screen Size [inch (m)]
(a) [inch (m)]
(b)
[inch (cm)]
Min. Max.
30 (0.8) 36(0.9) 74(1.9) 18(46)
40 (1.0) 49(1.2) 99(2.5) 24(61)
50 (1.3) 62(1.6) 125(3.2) 30(76)
60 (1.5) 74(1.9) 150(3.8) 36(91)
70 (1.8) 87(2.2) 175(4.4) 42(107)
80 (2.0) 99(2.5) 200(5.1) 48(122)
90 (2.3) 112(2.8) 225(5.7) 54(137)
100 (2.5) 124(3.2) 251(6.4) 60(152)
120 (3.0) 150(3.8) 301(7.6) 72(183)
150 (3.8) 187(4.8) 377(9.6) 90(229)
200 (5.1) 250(6.4)
503(12.8)
120(305)
250 (6.4) 313(8.0)
629(16.0)
150(381)
300 (7.6) 376(9.5)
755(19.2)
180(457)
(a)
(b)
Screen
Reference for
the 4:3 aspect ratio
Side View
Side View
Screen
size
Screen
size
8
Generally, better quality of a picture is available when the lens shift is set
to the center.
Do not attach anything other than specified options (such as an optional conversion
lens) to the screw thread. For details, please ask your dealer.
NOTE
Adjusting The Projector's Elevator
Using The Picture Shift Dials
CAUTION
If you press the elevator buttons without holding the projector, the
projector might crash down, overturn, smash your fingers and possibly result in
malfunction. To prevent damaging the projector and injuring yourself, ALWAYS HOLD
THE PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
You can use the elevator feet to make adjustments if the surface on which you need to set
the projector is uneven or if you otherwise need to adjust the angle of projection. The
adjustment range of the elevator feet is 0 to 9 degrees.
The lens of this projector can be shifted horizontally and vertically. When you want to
finely adjust the picture position, use the picture shift dials.
Using the horizontal picture shift dial shifts the picture to right or left.
Using the vertical picture shift dial shifts the picture upward or downward.
1
Press and hold in the elevator buttons.
2
Raise or lower the projector to the
desired height and then release the
elevator buttons.
When you release the elevator buttons, the elevator
feet will lock into position.
3
As necessary, you can also finely
adjust the height of the projector by
twisting the elevator feet by hand.
Elevator buttons
Elevator feet
Setting Up (continued)
Horizontal picture shift dial
7.5:2.5
to
2.5:7.5
10:0
to
0:10
Vertical picture shift dial
9
Connecting Your Devices
WARNING Incorrect connecting could result in fire or electrical shock.
Whenever attempting to connect other devices to the projector, please thoroughly read
the "User's Manual - Safety Guide", this manual and the manual of each device to be
connected.
CAUTION
TURN OFF ALL DEVICES prior to connecting them to the projector.
Attempting to connect a live device to the projector may generate extremely loud
noises or other abnormalities that may result in malfunction and/or damage to the
device and/or projector.
ATTENTION
Make sure that you connect devices to the correct port. Incorrect
connection may result in malfunction and/or damage to the device and/or projector.
Refer to the section TECHNICAL of this manual for the pin assignment of connectors
and RS-232C communication data.
Some cables have to be used with core set. Use the accessory cable or a
designated-type cable for the connection. For cables that have a core only at one end,
connect the core to the projector.
Secure the screws on the connectors and tighten.
Whenever attempting to connect a laptop computer to the projector, be sure to
activate the laptops RGB external image output (set the laptop to CRT display or to
simultaneous LCD and CRT display). For details on how this is done, please refer to the
instruction manual of the corresponding laptop computer.
About Plug-and-Play Capability
This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by
connecting this projector to computers that are VESA DDC (display data channel)
compatible. Please take advantage of this function by connecting the accessory RGB
cable to the COMPUTER port (DDC 1/2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices).
Please use the standard drivers in your computer as this projector is a Plug-and-Play
monitor.
NOTE
Some computers may have multiple display screen modes. Use of some of
these modes will not be possible with this projector.
For some COMPUTER input modes, the optional Mac adapter is necessary.
When the image resolution is changed on a computer, depending on an input,
automatic adjust function may take some time and may not be completed. In this case,
you may not be able to see a check box to select Yes/No for the new resolution on
Windows. Then the resolution will go back to the original. It might be recommended to
use other CRT or TFT monitors to change the resolution.
NOTE
Setting Up (continued)
10
Please refer to the following for connecting your devices.
See the rear of the projector and open the ports cover.
You can see the ports.
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
S-VIDEO
AUDIO
Y
COMPONENT VIDEO
C
B/PB CR/PR
COMPUTER
CONTROL
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
L-AUDIO-R
VIDEO
Connecting to a computer
RGB out RGB cable (D-sub 15 pin)
Audio out Audio cable (Stereo mini)
RS-232C port RS-232C cable
Connecting to a DVD/VCR player
Video out
Audio out (L) Audio/Video cable
Audio out (R)
If using a SCART RGB input,
Video
AUDIO-L
AUDIO-R SCART SCART cable
G out port
B
R
If using a S-video input,
S-video out port S-video cable
Audio out (L) Audio cable
Audio out (R)
If using a component input,
Component (Y) out
Component (CB
/PB) out Component cable
Component (C
R/PR) out
Audio out (L) Audio cable
Audio out (R)
If using a component input from
COMPUTER port,
Component (Y) out
Component (C
B/PB) out Component cable
Component (C
R/PR) out (with D-sub 15 pin)
Audio out Audio cable(Stereo mini)
Setting Up (continued)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Hitachi PJTX10WAU User manual

Category
Data projectors
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI