Freshpoint 161114 Owner's manual

F1B1-RCFDF1-RCFDF1-RC GRO75-RC

F1GC-RC

GRO-475BP

REVERSE OSMOSIS WATER FILTRATION SYSTEM

INSTALLATION AND OPERATION MANUAL

FreshPoint GRO-475BP

Filtration System

INSTALLATION INSTRUCTIONS

English ................................Pages 3-16

Repair Parts ..............................Pages 14

FreshPoint GRO-475BP

Sistema de filtración

INSTRUCCIONES DE INSTALACIÓN

Español ............................. Páginas 17-30

Piezas de repuesto ......................Páginas 28

FreshPoint GRO-475BP

Système de filtration

DIRECTIVES D'INSTALLATION

Français .............................. Pages 31-44

Piéces de Rechange .......................Pages 42

F1B1-RCFDF1-RCFDF1-RC GRO75-RC

F1GC-RC

IMPORTANT: Before installing this reverse osmosis system,

make certain your water supply complies with the following

operating specifications. Failure to do so may reduce the

effectiveness of the system and will void the warranty.

SPECIFICATIONS

Recommended

Feed Pressure Range: 10 to 60 psi (0.69–4.14 bar)

Pressure Range: 40 to 100 psi (2.75–6.89 bar)

Temperature Range: 40–100°F (4.4–37.8°C)

Operating Voltage: 110 volts

TDS: <2000 ppm

Maximum Hardness

†

: <10 gpg (170 mg/L)

Sulfide, Iron and Manganese

‡

: <0.1 ppm

Chlorine in Water Supply: <2 ppm

pH Limits: 3–11

Overall Dimensions: 17.82"W x 5.46"D x 12.54"H

(453mm x 139mm x 319mm)

Weight: 12.75 lbs (5.78 kg)

Tank Dimensions: 10.91"DIA x 14.61"H

(277mm DIA x 371mm)

Tank Capacity Max: 3.2 gal (12.1 L)

Tank Air Pressure Empty: 5-7 psi (0.34-0.48 bar)

Tank Weight (Full): 25.50 lb (11.6 kg)

†

If the hardness of your water is above 10 gpg (171 mg/L), lime

scale will build up rapidly on the membrane. Scale buildup will

plug the membrane and make the system ineffective. We do not

recommend these reverse osmosis systems to be used with

water in excess of 10 gpg (171 mg/L) hardness.

‡

A maximum total level of approximately 0.01 ppm sulfide, iron

or manganese is permissible. See your local dealer to reduce

these substances in your water.

PARTS INCLUDED:

• System with cartridges

• Storage Tank

• Installation Hardware Kit

• Lead-free drinking water faucet with air gap

CALIFORNIA PROPOSITION 65 WARNING

WARNING:

This product contains chemicals known to the

State of California to cause cancer or birth

defects or other reproductive harm.

Tools and Materials Required

• Hand or electric drill (cordless preferred)

• (2) Adjustable wrenches

• Slotted and Phillips screwdrivers

• File

• Safety glasses

• Drill bits: 1/8", 3/16", 1/4", 3/8"

• Tube cutter or utility knife

• Pencil

• Towel

• Bucket

• Screwdriver bits: 1/8", 3/16", 1/4", 3/8"

If sink does not have hole for separate faucet:

• Center punch

• 3⁄4" hole saw or drill bit

• Safety mask

NOTE: All tools may not be necessary for installation. Read

installation procedures before starting to determine

what tools are necessary.

FRESHPOINT GRO-475BP Installation and Operation Manual • 3

GENERAL

WARNING:

Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system.

Systems certified for cyst reduction* may be

used on disinfected waters that may contain

filterable cysts.

*NSF/ANSI Standard 53 and 58 certified to reduce cysts such

as Cryptosporidium and Giardia by mechanical means.

CAUTION

RO System must be protected against freezing,

which can cause cracking of the RO components

and water leakage.

NOTE:

• Your water must be within required limits for satisfactory

operation. If not, your membrane life may be shortened and

your warranty will be voided (see Specifications on page 3).

• This reverse osmosis system will not protect against

disease-causing bacteria or remove naturally-occurring

harmless bacteria.

• Install on cold water line only.

• Make certain that installation complies with all state and

local laws and regulations.

• The replacement cartridges and reverse osmosis element

included with this system have limited service lives. Changes

in taste, odor, and color of the water being filtered indicate

that the cartridge should be replaced.

• After prolonged periods of non-use (such as during a

vacation) it is recommended that the system be flushed for 5

minutes before it is used.

• A drinking water cartridge may contain carbon fines (very

fine black powder). After installation, flush the system for 5

minutes to remove the carbon fines before using the water.

• It is recommended that you run the tap at least 20 seconds

prior to using water for drinking or cooking purposes.

• The contaminants or other substances removed or reduced

by this water treatment device are not necessarily present in

your water.

HOW REVERSE OSMOSIS WORKS

The GRO-475BP Reverse Osmosis (RO) System uses a

semi-permeable membrane to reduce dissolved salts and

minerals, improving the taste and odor of your water. The RO

membrane is made of layers of micron-thin film wound around

a hollow center core. Water molecules can pass through the

membrane, but dissolved salts and minerals are rejected.

The GRO-475BP Reverse Osmosis System features 4-stage

filter action. Your water supply is pre-filtered to reduce dirt

and chlorine that may foul the membrane. The RO membrane

separates this pre-filtered water into PRODUCT WATER and

DRAIN or REJECT WATER. Incoming water pressure forces

the product water through the membrane and into the storage

tank. Dissolved solids and other contaminants cannot pass

through the membrane and are sent to the drain as reject

water. When you open the drinking water faucet, product water

is drawn from the storage tank through an activated carbon

post-filter, providing you with cleaner, great-tasting water.

For each gallon of water produced, several gallons are

discharged as reject water. The storage tank can hold up to

2.1 gallons (7.9 L) of water at a time, for drinking and cooking

needs. When used under the Specifications on page 3 of the

manual, your Reverse Osmosis membranes should last 12-24

months.

PRECAUTIONS

WARNING:

Improper connection of the appliance-

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician or service representative if

you are in doubt whether the appliance is

properly grounded. Do not modify the plug

provided with the appliance; if it will not fit

the outlet, have a proper outlet installed by a

qualified technician.

A. The power-supply receptacle for the

appliance shall be installed in a cabinet or on

a wall adjacent to the undercounter space in

which the appliance is to be installed;

B. There shall be an opening through

the partition between the compartments

specified in (a) that is large enough for

the attachment plug to pass through. The

longest dimension of the opening shall not

be more than 1-1/2 in (38 mm);

C. The edges of the opening specified in (B)

shall, if the partition is wood, be smooth

and rounded, or, if the partition is metal, be

covered with an edge protector provided for

this purpose by the manufacturer; and

D. Care shall be exercised, when the

appliance is installed or removed, to reduce

the likelihood of damage to the supply cord.

INSTALLATION

GROUNDING INSTRUCTIONS: This appliance must be

grounded. In the event of a malfunction or breakdown,

grounding will reduce the risk of electric shock by providing a

path of least resistance for electric current. This appliance is

equipped with a cord having an appliance-grounding conductor

and a grounding plug. The plug must be plugged into an

appropriate outlet that is installed and grounded in accordance

with all local codes and ordinances.

4 • FRESHPOINT GRO-475BP Installation and Operation Manual

1

RO INLET LINE (WHITE)

CONNECT TO

WATER SUPPLY LINE

RO OUTLET LINE (BLUE)

RO DRAIN LINE (1/4" RED)

RO LINE TO TANK (WHITE)

DRAIN PIPE

FAUCET DRAIN LINE (3/8" RED)

CONNECT

TO PUMP

CONNECT

TO POWER

SUPPLY

INSTALLATION CONTINUED . . .

• Please read all instructions and precautions before installing and using

your GRO-475BP.

• For standard, under-sink installation on 3/8" (9.52 mm) steel, brass, or

copper cold water line.

• When selecting a mounting location of the system and tank, take into

consideration the length of tubing required for connections between existing

plumbing and system components. Some installation sites may require

more tubing than provided in the kit.

• Ensure that the system's installation location is within 5 feet (1.52 meters)

of a 110 volt grounded outlet.

• Numbered diagrams correspond with numbered steps.

1. Installing the Water Supply Adapter

The supply adapter fits 1/2"-14 NPS supply threads or

3/8" x 3/8" compression. If local codes permit, it may be used to connect the

system to the cold water supply line. If local codes do not permit the use of the

supply adapter, alternate connectors can be obtained from your local supplier.

Directions:

(A) Turn off cold water supply line. If cold water line does not have a shut-off

valve under the sink, you should install one.

(B) Turn on the cold water faucet and allow all water to drain from line.

(C) Disconnect riser cold water supply valve.

(D) Ensure the sealing gasket is fully seated into the feed adapter valve female

thread.

(E) Install feed adapter valve onto supply valve as desired. The feed adapter valve

may be installed at the bottom of the supply hose or the top of the cold water

line. Hand tighten only.

(F) Connect the riser to the feed adapter valve.

NOTE: Be careful not to cross-thread.

FRESHPOINT GRO-475BP Installation and Operation Manual • 5

INSTALLATION CONTINUED . . .

2. Selecting the Faucet Location

The drinking water faucet should be positioned with function, convenience, and

appearance in mind. An adequate flat area is required to allow faucet base to rest

securely. The faucet fits through a 3/4" hole. Most sinks have pre-drilled 1-3⁄8" or

1-1⁄2" diameter holes that may be used for faucet installation. If these pre-drilled

holes cannot be used or are in an inconvenient location, it will be necessary to

drill a 3/4" hole in the sink to accommodate the faucet.

CAUTION

This procedure may generate dusts which can cause severe irritation if

inhaled or come in contact with the eyes. The use of safety glasses and

safety mask for this procedure is recommended.

CAUTION

DO NOT ATTEMPT TO DRILL THROUGH AN ALL-PORCELAIN SINK. If

you have an all-porcelain sink, mount the faucet in pre-drilled sprayer

hole or drill through countertop next to sink.

CAUTION

When drilling through a countertop, make sure the area below the

drilled area is free of wiring and piping. Make certain that you have

ample room to make the proper connections to the bottom of the

faucet.

CAUTION

Do not drill through a countertop that is more than 1" thick.

CAUTION

Do not attempt to drill through a tiled, marble, granite or similar

countertop. Consult a plumber or the countertop manufacturer for

advice or assistance.

The following instructions apply to stainless steel sinks ONLY.

(A) Line bottom of sink with newspaper to prevent shavings, parts or tools from

falling down the drain.

(B) Place masking tape over the area to be drilled to help prevent scratches if

drill bit slips.

(C) Mark point with center punch. Use a 1/4" drill bit to drill a pilot hole through

sink.

(D) Use a 1-

1

⁄4" hole saw to enlarge hole. Smooth rough edges with a file.

3. Mounting the Faucet

WARNING:

Due to variance in installation sites, it is highly recommended to

install the 1/4" red drain tubing to the RO system manifold before

fully mounting the faucet. Make note of the 1/4" red drain tubing

length required to reach from the RO system manifold to the

faucet connection and plan accordingly in relation to mounting

location of system components. Furthermore, the 1/4" red drain

tubing includes a flow controller installed in one end of the

tubing. The end of the tubing with the flow restrictor must be

securely installed into the RO system manifold before attaching to

the faucet. DO NOT cut off the flow restrictor.

NOTE: Not all parts provided with the faucet may be needed for installation.

(A) Slide chrome plate and black rubber washer onto faucet by threading both

drain tubes through the holes on the plate and washer.

(B) Attach large diameter red 3/8" drain tube to barb fitting at the faucet base.

This tube should be long enough to reach the drain clamp in Step 4.

(C) Locate the small diameter red 1/4" drain tube connected to the drain port

of the GRO element. Route the tubing to the faucet and cut off the excessive

length of tubing.

(D) Slide white extension spacer onto long threaded section of faucet. Open end

of extension should come in contact with base of faucet.

(E) Screw washer, lockwasher, and locking nut onto end of faucet threads

(F) Screw quick connector onto end of facuet threads.

(G) Wet end of 3/8" blue tube. Push into bottom of quick connector. Tug gently to

be sure connection is complete.

NOTE: To remove the tube, push on the fittings' collar and pull the tube out.

(H) Holding the faucet, feed the three tubes through the hole in the sink. Position

the faucet handle at a desired location

(I) Center the faucet and slip slotted disc between the white extension spacer

and the bottom of the counter or sink. Tighten the locking nut with a wrench

until it is tight.

D

C

1

⁄

4”

1

⁄4”

A

B

C

D

Pilot Hole

Mounting

Hole

1

⁄4"

1/4"

2

CHROME PLATE

SLIP SLOTTED DISC

COUNTER TOP

WASHER

LOCKWASHER

LOCKING NUT

QUICK CONNECTOR

BARB FITTING

(3/8” RED FAUCET DRAIN LINE)

TUBING (3/8” BLUE RO OUTLET LINE)

BARB FITTING

(1/4” RED RO DRAIN LINE)

BLACK RUBBER WASHER

WHITE EXTENSION SPACER

3

C

B

A

I

D

E

H

F

G

6 • FRESHPOINT GRO-475BP Installation and Operation Manual

4. Installing the Drain Clamp

NOTE: If you have a single-basin sink with a disposal unit, call Technical Support

for options.

NOTE: Before installing the drain clamp, check the drainpipes under the sink

for corrosion. Corroded pipes should be replaced before continuing with

installation.

(A) Attach the drain clamp to a vertical section of the drainpipe, about 6" above

the trap. Make sure the opening on the drain clamp is facing towards the

drinking water faucet.

(B) Using the fitting hole of the drain clamp as a guide, drill a 1/4" hole through

one side of the drainpipe.

(C) Remove the drain clamp from the drainpipe and enlarge the hole with a

3/8" drill bit. Use a file to remove rough edges from the drilled hole.

(D) Make sure the black rubber gasket is adhered to the inside of the drain clamp

and place the drain clamp assembly over the drilled hole. Look through the

hole and position the clamp so that the center of the clamp hole is slightly

higher (about 1/16") than the center of the drilled hole. Tighten the clamp

securely.

(E) Screw the plastic compression nut onto the drain clamp until hand-tight.

5. Connecting the Faucet to the Drain

CAUTION

This is a gravity drain line. Any loops, kinks or sharp bends must be

eliminated before proceeding. Failure to create a straight line to the

drain may result in reject water leaking through the air gap in the

faucet onto the countertop and below the faucet.

(A) Align the larger reject 3/8" red tubing from the faucet with the compression

nut on the drain clamp. Create as straight and smooth a path as possible with

the tubing. Do not kink tube. Cut the tubing squarely and remove any internal

and external burrs. Insert inner tube insert (white cone) into end of 3/8" red

tubing. Remove compression nut from the drain clamp. Place compression

nut on end of 3/8" red tubing.

(B) Insert the tubing into the drain port until it stops. Tighten the compression nut

with fingers, then tighten 1 to 2 turns with a wrench to secure tubing to drain

port.

6. Mounting the System

WARNING:

When selecting a mounting location of the system and tank, take

into consideration the length of tubing required for connection

between components. Some installation sites may require more

tubing than provided in the kit.

(A) Select a location under the sink, or other suitable area where the system will

be installed.

NOTE: The system carton can be used to determine the operational footprint

required for installation of the system and replacement cartridges.

(Figure 6)

(B) Mount the system vertically. Ensure mounting is level. Remove filter

cartridges for easier access to bracket mounting holes. Place a pencil mark

in the upper slots of the bracket mounting holes. (Figure 4b). Alternate

mounting option: If mounting the system near the floor, place the pencil

marks above each of the mounting holes on the bracket to ensure enough

space resides below the cartridge and the floor for cartridge replacement

(Figure 4c). Use the 3/32" drill bit to create pilot holes for mounting.

WARNING:

The system should be mounted to a firm, solid surface that is

able to support the weight of the system.

7. Connecting the Faucet to the System

(A) Determine the length of plastic blue tubing needed to connect to the outlet

(right) side of the filter from the faucet. Be sure to allow enough tubing to

prevent kinking and cut the tubing squarely. Use a marker to mark one end of

the tubing 5/8" from the end. Wet the end of the 3/8" tube and push into the

outlet (right) connection of the system up to the mark.

CAUTION

Do not bend or crimp tube while inserting.

(B) Gently pull back on the tube to ensure it is connected properly.

4

A

B C

6"

D

E

5

A

B

3/8" Tube

7” (178 mm)

16.25”

(413 mm)

14”

(356 mm)

6

FRESHPOINT GRO-475BP Installation and Operation Manual • 7

7

RO DRAIN LINE

(3/8" RED)

RO LINE TO TANK

(3/8” BLUE)

FAUCET DRAIN LINE (1/4” RED)

RO OUTLET LINE (3/8” BLUE)

RO INLET LINE (3/8” WHITE)

8 • FRESHPOINT GRO-475BP Installation and Operation Manual

INSTALLATION CONTINUED . . .

8. Connecting the Storage Tank to the System

CAUTION

When tank is full, it weighs approximately 19.50 lbs. (8.8 kg.) Provide

ample support under the tank.

(A) To prevent leaks, apply 3 or more wraps of plumber tape to threads on tank.

Thread the tank valve onto the top of the tank opening. Turn tank so handle is

in line with tubing.

CAUTION

The tank/valve connection will leak if not properly sealed. Plumber

tape will normally seal the threaded connection.

(B) Locate the 3/8" blue tubing. Place a mark on the tubing 5/8" from one end.

Moisten the marked end of the tubing with water and insert with a twisting

motion into the port of the tank valve until the 5/8" mark is flush with the

quick connect fitting. Then locate the tank near the system's installation

area.

(C) Cut the tubing to correct length. Install free end of tubing into white

quick-connect fitting on the system. Ensure the tubing does not kink. Retain

remaining blue tubing for use in connecting system to water supply adapter.

Some installation sites may require additional tubing not provided in kit.

(D) Place entire system over mounting screws on wall and slide down.

CAUTION

Make certain system is firmly attached to wall to prevent it from falling

and possibly becoming damaged.

NOTE: Use caution not to bend or pinch the tubing behind the system while

attaching to mounting screws.

9. Connecting the System to the Water Supply Adapter

(A) Locate remaining length of 3/8" plastic blue tubing.

(B) Place a mark on the tubing 5/8" from the end. Moisten the end of the tubing

with water and insert with a twisting motion push into white quick connect

fitting on the left side of system. Depending on the installation, the system

may need to be removed from the mounting surface to access the left side of

the system.

(C) Cut the tube to a length that will allow connection to the Water Supply

Adapter. Ensure the tubing does not kink. Place a mark on the tubing

5/8" from the end. Moisten the end of the tubing with water and insert with a

twisting motion push into quick connect fitting on the Water Supply Adapter.

10. Faucet Operation

(A) For controlled water flow, push the handle down.

(B) For constant water flow, lift the faucet handle to lock it in the open position.

8

A

B

3/8" Tube

Apply

plumber

tape

5/8"

Push Down

Push Up

A

B

10

RO DRAIN LINE

(3/8" RED)

RO LINE TO TANK

(3/8” BLUE)

FAUCET DRAIN LINE (1/4” RED)

RO OUTLET LINE (3/8” BLUE)

RO INLET LINE (3/8” WHITE)

9

FRESHPOINT GRO-475BP Installation and Operation Manual • 9

11. System Start-up

NOTE: The reverse osmosis membrane is treated with a food grade sanitizing

agent that may cause an undesirable taste. Although it is not harmful, it

should be flushed from the system.

NOTE: The post-polishing filter may contain fine black carbon particles. These

fines are harmless, but may make the water appear gray in color. The

carbon fines are flushed from the system with the first tank full of water.

NOTE: The RO system does not produce a high volume of water on demand as an

ordinary filter does. Water is produced at a slow, drop-by-drop rate. The

system requires about 2 to 4 hours to fill the storage tank. As water is

taken from the tank, the system automatically starts the cycle of replacing

the water and then stops water production when the tank is full.

CAUTION

Visually check the entire system for leaks.

If a leak is present, see

Troubleshooting on page 14.

(A) Turn off valve at top of storage tank.

(B) Turn on the cold water supply slightly, and ensure the supply adapter valve is

open.

(C) Lift the faucet handle to lock it in the open position and let it drip for 30 min.

(D) Completely open the cold water supply until it comes to a stop. Allow water

to drip from the faucet for 12 more hours. Then close the faucet and open the

valve on the storage tank. The tank valve is open when the handle lines up

with the tubing connection.

(E) Plug the booster pump into a 110 volt grounded outlet.

(F) Allow 3 hours for the tank to fill. Continue to periodically check the

installation for leaks. After the storage tank is filled, open the faucet to flush

the post-filter cartridge. Allow 4 to 5 minutes for all of the water to drain from

the tank. Close faucet and allow tank to fill.

(G) Repeat step F four times.

NOTE: Initially, the water may appear cloudy. This is a result of air trapped in

the post-polishing filter. It is not harmful and will disappear in a matter

of minutes. It may take up to a week after installing a new post-polishing

filter for the trapped air to dissipate.

The system is ready for operation. You can now enjoy quality water from your

Reverse Osmosis System.

TESTING YOUR REVERSE OSMOSIS SYSTEM

(NON-MONITORED SYSTEMS ONLY)

Model GRO-475BP Reverse Osmosis System

Total Dissolved Solids (TDS) Test

NOTE: It is highly recommended that you (the consumer) have your water

tested at least every 6 months to verify that your system is performing

satisfactorily.

SAMPLING INSTRUCTIONS:

Sampling instructions are included with the Total Dissolved Solids (TDS) Test Kit.

Total Dissolved

Solids Test Kit

11

Closed Tank Valve

Open

Tank Valve

Counter-

clockwise

A

B

10 • FRESHPOINT GRO-475BP Installation and Operation Manual

OPTIONAL INSTALLATION

Connecting your Reverse Osmosis System to Refrigerator Icemaker / Water Dispenser

CAUTION

If you are connecting this unit to your refrigerator/icemaker with initial RO installation, wait to turn on the icemaker

until the post-polishing filter has been flushed according to Step 11.

CAUTION

Use plastic tubing and fittings. Do not use copper tubing or brass fittings.

NOTE:

For optimum performance, it is recommended that the distance between the RO system and the refrigerator icemaker/water

dispenser be no greater than 10 feet (3 m). At distances greater than 10 feet, the water pressure from the system may not be

adequate to deliver water to the refrigerator.

MATERIALS REQUIRED(available from your local hardware store):

• 3/8" x 3/8" x 3/8" (0.952 mm x 0.952 mm x 0.952 mm) compression or quick-connect tee

• 10 feet (3 m) of 3/8" (0.952 mm) polyethylene tubing

• Shut-off valve

1. Turn off refrigerator water supply and icemaker (consult manufacturer’s guidelines).

2. Close tank valve (on top of storage tank).

3. Turn off water to RO system at the cold water supply, or at the feed water supply adapter.

4. Open drinking water faucet to relieve pressure.

5.

Locate tubing (permeate) leading to your drinking water faucet. Cut and insert the

3/8"

x

3/8"

x

3/8"

compression or quick-connect tee into the permeate tubing.

Consult manufacturer’s guidelines before installing the supply adapter.

NOTE: When cutting the permeate tubing, you may experience some water leakage.

6. Using a length of 3/8" polyethylene tubing, connect the

icemaker/dispenser line with the free port on the compression tee.

7. The shut-off valve should be installed as close to this port of the tee

as possible. Shut-off valve should be installed in the OFF position

Consult manufacturer’s guidelines before installing the shut-off valve.

8. Completely open cold water supply.

9. Open tank valve.

10. Turn off the drinking water faucet.

11. Turn on water to RO system at cold water supply.

12. Turn on icemaker and open shut-off valve.

Consult manufacturer’s instructions.

13. Check for leaks and tighten connections if necessary.

1

4

7

6

5

2

3

FRESHPOINT GRO-475BP Installation and Operation Manual • 11

Filter Cartridge Replacement

NOTE: The life of the filter cartridges depends on water

volume used and the quality of the feed water. It is

recommended that the filter cartridges be replaced

every 6-12 months, or when there is a noticeable

change in taste, odor, or flow of filtered water.

Ensure the correct cartridge is purchased for the

system.

Model GRO-475BP uses FDF1-RC, GRO75-RC, F1B1-RC, and

F1GC-RC Replacement Cartridges

1. Cartridge Replacement

A. Relieve pressure by turning off the water supply to the

system and opening a faucet until water flow stops (wait 5

to 10 minutes after water stops to relieve pressure in RO

membrane). Place a bucket or towel under the system to

catch any water drips.

B. Lift the locking bar upward until the filter cartridge

disengages from the filter head assembly (Figure A).

C. Pull the cartridge away from the filter head assembly and

ensure the locking bar remains in the fully up position

(Figure B).

D. Align the posts on the filter cartridge with the ports in the

filter head assembly. Slide the cartridge filter into the filter

head assembly (engaging with the locking bar causing it to

drop forward and down). (Figure C).

E. Pull down the locking bar until it snaps into place

(Figure D).

Troubleshooting

Leaks between filter head assembly and filter

cartridge

1. Relieve pressure by turning off the water supply to the

system and opening faucet until water flow stops. Place a

bucket or towel under the system to catch any water drips.

2. Remove cartridge and inspect O-rings to make sure they

are seated and clean.

3. Install filter cartridge. Place system into operation and

check for leaks. If leaks persist, turn off the water supply

and contact Technical Support at 1-800-279-9404.

Leaks from tubing fittings

1. Relieve pressure by turning off the water supply to the

system and opening faucet until water flow stops. Place a

bucket or towel under the system to catch any water drips.

2. Depress collet on system or inlet supply adapter tubing

fittings and pull tubing from fitting. Inspect surface of

tubing for scratches or debris. Clean or cut back tubing to

access clean surface.

3. Wet the end of the inlet tubing and press into the inlet

fitting of the system. Ensure the tubing is fully pushed past

the fitting O-rings. Place system into operation and check

for leaks. If leaks persist, turn off the water supply and

contact Technical Support at 1-800-279-9404.

A

C

B

D

Cartridge Sequence

GRO-475BP

F1B1-RCFDF1-RCFDF1-RC GRO75-RC

F1GC-RC

12 • FRESHPOINT GRO-475BP Installation and Operation Manual

Leaks on tank valve assembly

1. Open drinking water faucet to drain storage tank. Let

drinking water faucet run until it drips. Turn off cold water

supply.

2. Push in on white collar of tank valve fitting and pull out

tubing. Unscrew the tank valve from the storage tank.

Rewrap threads on top of the tank with plumber tape. Screw

tank valve back onto tank. Trim 1/2" from end of tubing and

reinsert 5/8" into tank valve fitting.

3. Open the cold water supply and shut off the reverse osmosis

faucet. Let the system pressurize for several hours and

check for leaks. Check again after tank is fully pressurized.

Leaks on quick-connect fittings

1. Close the cold water supply and tank valve.

2. Depress plastic collar and pull out tubing.

3. Cut off 1" of tubing and place a mark 5/8" from end of

tubing. Tubing should be cut squarely. The internal and

external burrs should be removed.

4. Push tubing 5/8" into fitting.

5. Open the cold water supply and tank valve. If leaks persist,

call Technical Support.

High TDS in Product Water

If high levels of TDS (Total Dissolved Solids) are detected in

your product water as determined by the TDS Monitor or by the

TDS test kit, the cartridge membrane may need to be replaced

or the reject flow control may be clogged. See your dealer or

plumber to check product water TDS.

Reduced production

Slow or no product water flow usually indicates a clogged

cartridge.

Gradual return of taste and odor

Gradual return of unpleasant taste and odor over a period of

time may indicate that your cartridges need to be replaced.

Sudden return of taste and odor

If shortly after complete servicing noticeable taste and odors

return, contact Technical Support.

No water pressure from the drinking water faucet

or low volume in storage tank

1. Close the cold water supply to system.

2. Lift storage tank to see if it is empty. If not, open the

drinking water faucet to empty water from tank.

NOTE: It may be necessary to pump a small amount of air into

the tank with a bicycle pump to remove all the water

from the tank.

3. When tank is empty, use a pressure gauge to check

tank pressure. An empty tank should contain 5 to 7 psi

pressure. Increase or decrease the air pressure in the tank

accordingly.

4. Open cold water supply. Let system run for 3 hours to fill

tank, then check system performance. If performance has

not improved, call Technical Support.

TROUBLESHOOTING GUIDE

FRESHPOINT GRO-475BP Installation and Operation Manual • 13

GRO475BP PARTS GUIDE

For replacement parts, contact your nearest Water Filter dealer or call 800.279.9404

8

3

9

4

7

6

1

5

2

11

10

ITEM NO. PART NO. DESCRIPTION QTY

1 4005009 RO HEAD, MODEL GRO-475B 1

2 4004588 KIT, TUBING/ELBOWS, RO 1

3 4004916 ASSY, 4 STAGE COVER, MAGNET 1

4 655123-96 FDF1-RC 1

5 655122-96 GRO75-RC 1

6 655120-96 F1B1-RC 1

7 655117-96 F1GC-RC 1

8 244877 TANK, RO (STL 4.4 GAL) 1/4" NPT 1

9 4003280 SCHROUD, ASO 1

10 4004662 KIT, RO SYSTEM 75 GPD 1

11 244820 FAUCET AIR-GAP 1

14 • FRESHPOINT GRO-475BP Installation and Operation Manual

System Tested and Certified by NSF International

against NSF/ANSI Standard 42, 53, 58, and CSA

B483.1 for the reduction of the claims specified on the

Performance Data Sheet.

C US

IMPORTANT:

Read this performance data and compare the capabilities of

this system with your actual water treatment needs.

It is recommended that before installing a water treatment

system, you have your water supply tested to determine your

actual water treatment needs.

This system has been tested according to NSF/ANSI 58 for the

reduction of substances listed below. The concentration of the

indicated substances in water enteringthe sysem was reduced

to a concentration less than or equal to the permissible limit

for water leaving the system as specified in NSF/ANSI 58.

The GRO-475BP shall only be used for arsenic reduction on

chlorinated water supplies containing detectable residual free

chlorine at the system inlet. Water systems using an in-line

chlorinator should provide a one-minute chlorine contact time

before the RO system.

WARNING:

Do not use with water that is microbiologically

unsafe or of unknown quality without adequate disinfection

before or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain filterable

cysts.

NOTE: Substances reduced are not necessarily in your water.

Filter must be maintained according to manufacturer’s

instructions, including replacement of filter cartridges.

The tested efficiency rating for these systems is 51.42%.

Efficiency rating means the percentage of the influent water

to the system that is available to the user as reverse osmosis

treated water under operating conditions that approximate

typical daily usage.

The tested recovery rating is 55.82%. Recovery rating means

the percentage of the influent water to the membrane portion

of the system that is available to the user as reverse osmosis

treated water when the system is operated without a storage

tank or when the storage tank is bypassed.

The GRO-475BP has been tested for the treatment of water

containing pentavalent arsenic [also known as As(V), As(+5),

or arsenate] at concentrations of 0.050 mg/L or less. This

system reduces pentavalent arsenic, but may not remove

other forms of arsenic. This system is to be used on water

supplies containing a detectable free chlorine residual or on

water supplies that have been demonstrated to contain only

pentavalent arsenic. Treatment with chloramine (combined

chlorine) is not sufficient to ensure complete conversion

of trivalent arsenic to pentavalent arsenic. Please see the

Arsenic Facts section of the Performance Data Sheet for

further information.

PERFORMANCE DATA

EPA # 082989-CHN-001

System Production Rate: 94.38 gpd (357.3 Lpd)

Recovery Rating: 55.82%

Efficiency Rating: 51.42%

TDS Rejection: 98.0%

Model GRO-475BP

Substance

Inﬂuent Challenge

Concentration

Max Permissible

Product Water

Concentration

Reduction

Requirements

Average

Reduction

Standard 42

Chlorine

Taste and Order

2.0 mg/L ± 10% ≥50% 95.9%

Standard 53

Cysts* Minimum 50,000/L 99.95% 99.99%

Atrazine 0.009 mg/L ± 10% 0.003 mg/L 93.7%

Lead (pH 6.5) 0.15 mg/L ± 10% 0.010 mg/L 99.9%

Lead (pH 8.5) 0.15 mg/L ± 10% 0.010 mg/L 99.6%

Lindane 0.002 mg/L ± 10% 0.0002 mg/L 97.4%

Standard 58

Total Dissolved Solids 750 ± 40 mg/L 187 mg/L 98.0%

Pentavalent Arsenic 0.050 mg/L ± 10% 0.010 mg/L 88.0%

Fluoride 8.0 mg/L ± 10% 1.5 mg/L 93.6%

Cysts* Minimum 50,000/mL 99.95% 99.99%

Turbidity 11 mg/L ± 1 NTU 0.5 NTU >99.1%

Lead 0.15 mg/L ± 10% 0.010 mg/L 98.6%

Selenium 0.10 mg/L ± 10% 0.05 mg/L 97.9%

Copper 3.0 mg/L ± 10% 1.3 mg/L 98.5%

Cadmium 0.03 mg/L ± 10% 0.005 mg/L 99.1%

Hexavalant Chromium 0.3 mg/L ± 10% 0.1 mg/L 96.4%

Trivalent Chromium 0.3 mg/L ± 10% 0.1 mg/L 98.2%

Radium 226/228 25 pCi/L ± 10% 5 pCi/L 80.0%

Barium 10.0 mg/L ± 10% 2.0 mg/L 96.3%

* NSF/ANSI Standard 53 and 58 certiﬁed to reduce cysts such as Cryptosporidium and Giardia by

mechanical means.

GRO-475BP SYSTEM INSTALLED WITH

FDF1-RC, GRO75-RC, F1B1-RC, F1GC-RC

FILTER CARTRIDGES

This reverse osmosis system contains a replaceable

component critical to the efficiency of the system.

Replacement of the reverse osmosis component should

be with one of identical specifications, as defined by the

manufacturer, to ensure the same efficiency and contaminant

reduction performance.

FRESHPOINT GRO-475BP Installation and Operation Manual • 15

Arsenic Fact Sheet

Arsenic (abbreviated As) is found naturally in some well

water. Arsenic in water has no color, taste or odor. It must be

measured by a lab test. Public water utilities must have their

water tested for arsenic. You can get the results from your

water utility. If you have your own well, you can have the water

tested. The local health department or state environmental

health agency can provide a list of certified labs.

There are two forms of arsenic: pentavalent arsenic [also

called As(V), As(+5), and arsenate] and trivalent arsenic [also

called As(III), As(+3) and arsenite]. In well water, arsenic may

be pentavalent, trivalent, or a combination of both. Special

sampling procedures are needed for a lab to determine what

type and how much of each type of arsenic is in the water.

Check with the labs in your area to see if they can provide this

type of service.

Reverse osmosis (RO) water treatment systems do not remove

trivalent arsenic from water very well. RO systems are very

effective at removing pentavalent arsenic. A free chlorine

residual will rapidly convert trivalent arsenic to pentavalent

arsenic. Other water treatment chemicals such as ozone and

potassium permanganate will also change trivalent arsenic to

pentavalent arsenic. A combined chlorine residual (also called

chloramine) may not convert all the trivalent arsenic. If you get

your water from a public water utility, contact the utility to find

out if free chlorine or combined chlorine is used in the water

system.

The GRO-475BP system is designed to remove pentavalent

arsenic. It will not convert trivalent arsenic to pentavalent

arsenic. The system was tested in a lab. Under those

conditions, the system reduced 0.050 mg/L (ppm) pentavalent

arsenic to 0.010 mg/L (ppm)(the USEPA standard for drinking

water) or less. The performance of the system may be

different at your installation. Have the treated water tested for

arsenic to check if the system is working properly.

The RO component of the GRO-475BP system must be

replaced every 12-24 months to ensure the system will

continue to remove pentavalent arsenic. The component

identification and locations where you can purchase the

component are listed in the installation/operation manual.

16 • FRESHPOINT GRO-475BP Installation and Operation Manual

Page is loading ...

7

LÍNEA DE DESAGÜE DE ÓSMOSIS

INVERSA (3/8" ROJA)

LÍNEA DE ÓSMOSIS

INVERSA AL

TANQUE

(3/8” AZUL)

LÍNEA DE DESAGÜE DE LLAVE

(1/4" ROJA)

LÍNEA DE SALIDA DE

ÓSMOSIS INVERSA

(3/8" AZUL)

LÍNEA DE ENTRADA DE

ÓSMOSIS INVERSA

(3/8" BLANCA)

22 • FRESHPOINT GRO-475BP Installation and Operation Manual

Page is loading ...

GUÍA DE PARTES DE GRO475B

Para obtener piezas de repuesto, comuníquese con su distribuidor de Filtro de Agua más cercano o llame al 800.279.9404

8

3

9

4

7

6

1

5

2

11

10

ARTÍCULO

N.º

PIEZA N.º DESCRIPCIÓN CANT.

1 4005009 CABEZA DE ÓSMOSIS INVERSA, MODELO GRO-475B 1

2 4004588 KIT, TUBERÍA/CODOS, ÓSMOSIS INVERSA 1

3 4004916 CONJUNTO, CUBIERTA DE 4 ETAPAS, IMÁN 1

4 655123-96 FDF1-RC 1

5 655122-96 GRO75-RC 1

6 655120-96 F1B1-RC 1

7 655117-96 F1GC-RC 1

8 244877 TANQUE, ÓSMOSIS INVERSA (ACERO 4.4 GAL) 1/4" NPT 1

9 4003280 CAPUCHA, ASO 1

10 4004662 KIT, SISTEMA DE ÓSMOSIS INVERSA 75 GPD 1

11 244820 ESPACIO DE AIRE DE LLAVE DE AGUA 1

28 • FRESHPOINT GRO-475BP Installation and Operation Manual

Page is loading ...

7

TUYAU DE VIDANGE OI

(3/8 PO ROUGE)

TUYAU RO RELIÉ

AU RÉSERVOIR

(3/8 PO BLEU)

TUYAU DE VIDANGE RELIÉ AU

ROBINET (1/4 PO ROUGE)

TUYAU DE SORTIE OI

(3/8 PO BLEU)

TUYAU D'ADMISSION OI

(3/8 PO BLANC)

36 • FRESHPOINT GRO-475BP Installation and Operation Manual

Page is loading ...

GUIDE DES PIÈCES DU MODÈLE GRO475B

Pour obtenir des pièces de rechange, communiquez avec le détaillant de filtres à eau le plus près de chez vous ou composez le

1800279-9404.

8

3

9

4

7

6

1

5

2

11

10

NUMÉRO

D’ARTICLE

NUMÉRO DE

PIÈCE

DESCRIPTION QTÉ

1 4005009 TÊTE DE FILTRE OI, MODÈLE GRO-475B 1

2 4004588 TROUSSE, TUYAUX ET COUDES, OI 1

3 4004916 ENS., 4ÉTAPES, COUVERCLE, AIMANT 1

4 655123-96 FDF1-RC 1

5 655122-96 GRO75-RC 1

6 655120-96 F1B1-RC 1

7 655117-96 F1GC-RC 1

8 244877 RÉSERVOIR, OI (ACIER 4,4GAL) 1/4PO NPT 1

9 4003280 CAPOT, ARRÊT AUTO 1

10 4004662 TROUSSE, SYSTÈME OI 75GAL/J 1

11 244820 ROBINET AVEC COUPURE ANTI-RETOUR 1

42 • FRESHPOINT GRO-475BP Installation and Operation Manual

Page is loading ...

Freshpoint 161114 Owner's manual

This manual is also suitable for

Freshpoint 161114 Owner's manual

in other languages

Related papers

Other documents