GE GXFM07HBL User manual

1

Installation

Faucet Mount Filtration System –

Instructions

GXFM07HWW and GXFM07HBL

SAFETY PRECAUTIONS

• Check with your state and local public works

department for plumbing and sanitation codes.

You must follow these guidelines as you install

the Water Filtration System.

• Be sure the water supply conforms with the

Performance Data. If the water supply conditions are

unknown, contact your municipal water company.

• Commonwealth of Massachusetts Plumbing Code

248 CMR shall be adhered to. The use of saddle

valves is not permitted; please consult your local

plumber.

WARNING —

Do not use with water that is

microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system.

PARTS INCLUDED

• Faucet Mount Filtration System—

GXFM07HWW or GXFM07HBL

• Filter—FXMLH

• Battery

• Faucet adapters and gasket

Optional accessories are available (Visa, MasterCard or

Discover cards accepted) by visiting our Website at

GEAppliances.com or from Parts and Accessories,

call 800.626.2002 (U.S.) or 800.663.6060 (Canada).

49-50227-4 07-09 JR

PROPER INSTALLATION

This Water Filtration System must be properly

installed and located in accordance with the

Installation Instructions before it is used.

• Check with your local public works department

for plumbing codes. You must follow their guides

as you install the Water Filtration System.

• Use the Water Filtration System on a potable,

safe-to-drink, home COLD water supply only.

The filter cartridge will not purify water or make

unsafe water safe to drink.

• DO NOT use on HOT water (100°F max).

• Install or store where it will not be exposed to

temperatures below freezing or exposed to any

type of weather. Water freezing in the system

will damage it.

• Your Water Filtration System will withstand up

to 125 psi water pressure. If your house water

supply pressure is higher than 100 psi during the

day (it may reach higher levels at night), install

a pressure reducing valve before the system is

installed.

WARNING — Do not use with water that

is microbiologically unsafe or of unknown quality

without adequate disinfection before or after the

system. Systems certified for cyst reduction may

be used on disinfected water that may contain

filterable cysts.

WARNING — Discard all unused parts

and packaging material after installation. Small parts

remaining after installation could be a choke hazard.

• Do not install filter in an outside location.

These systems are Tested and Certified by WQA against

NSF/ANSI Standard 42 for the reduction of Particulate

Class 1, Chlorine Taste and Odor and NSF/ANSI

Standard 53. See performance data sheet for details.

General Electric Company,

Appliance Park, Louisville, KY 40225

INITIAL SET-UP (CONT.)

Insert the new battery “+” side up.

Replace the battery cover. Use the alignment

arrows to ensure you have the cap in the proper

position. Using a small coin or screwdriver, turn

clockwise to lock in place.

Using a ballpoint pen, push the RESET button.

The left green light on the cap will flash 5 times.

If the light does not flash, reinstall the battery.

Be sure the “+” side is up as shown in Step 5.

Align the cap with the filter housing (lights in the

front) and press it down into place.

NOTE: The cap is designed to fit on the filter housing

only one way.

6

5

8

7

Installation Instructions

INITIAL SET-UP

Wash hands.

Remove the cap of the filtration system by

inserting a small coin or screwdriver on the back

of the system and pry to remove cap.

Remove the packaging and label at the bottom

of the new filter. Then install the new filter. Be

sure to support the filter housing in your hand

and press the new filter into the housing firmly.

Then turn the filter clockwise until hand-tight.

Continue to turn until the tab lines up with

the non-filtered icon as shown below:

Take the cap and turn it over. Use a small coin

or screwdriver to rotate the battery cover

counterclockwise. Turn the cap right-side-up

and the battery cover will drop out.

4

3

2

1

Insert a small coin

or screwdriver

on the back and

pry to remove cap.

Insert a small coin or

screwdriver and turn

counterclockwise to

open.

Press RESET

button with a

ballpoint pen

after filter

and battery

replacement.

Insert a

small coin or

screwdriver

and turn

clockwise

to lock in

place.

2

Black tabs

Twist filter

clockwise

to install.

Tab on filter

will line up

with the

Non-filtered

icon when the

filter is fully

installed.

3

Installation Instructions

INSTALLING THE SYSTEM

Wash hands. Remove the

existing aerator from the sink

faucet. Do not discard gasket;

it may be necessary to use

the existing gasket for the

installation of adapters.

Identify the type of threads on

the faucet:

• External threads – No

adapters should be required.

Proceed to Step 3.

• Internal threads – Select the proper adapter

and washer combination from those provided.

Screw adapter and gasket onto faucet.

Be careful not to cross-thread the adapter;

tighten manually.

NOTE: Adapters and gaskets have been included to

connect to most faucets. To insure a leak-free seal, you

may need to use your existing gasket (removed during

Step 1) from your faucet’s aerator in addition to the

gasket included with this system. If the adapters

will not connect to your faucet, it is recommended

to consult a local plumbing or hardware store for

assistance in obtaining the correct adapter for

your faucet.

Connect the faucet mount filter to the

faucet/adapter by turning the collar to tighten

onto the threads of the faucet/adapter.

Be careful not to cross-thread the unit;

tighten manually. It is not recommended but

if necessary, you may use pliers to assist with

installation. Be careful not to damage the swivel

collar with the pliers.

Slowly turn on the cold water (about half open)

and check for leaks. Tighten as necessary.

With the cold water faucet fully open, rotate the

selector band to “Filtered Spray” or “Filtered

Stream.” Flush new filter for 10 minutes to

remove any harmless carbon fines that may

be in the system. The water will automatically

go back to “non-filtered water” when the cold

water faucet is shut off.

5

4

3

2

1

Gasket

Aerator

Faucet

adapters

and washers

Swivel

collar

OPERATION

After installing and flushing the filter system, fully open

the cold water and rotate the selector band on the filter to

“Filtered Spray” or “Filtered Stream.” The selector band

will automatically go back to the “non-filtered water”

position; however, you will continue to receive filtered water

until you turn the faucet off. You do not have to hold the cap

to continue receiving filtered water. The green LED light will

indicate the water pattern mode the system is in. Allow

water to run for 3 seconds before use. When your water

needs are finished, simply turn off the cold water. The water

will automatically return to the non-filtered water mode

when the water supply faucet is shut off.

FILTERED SPRAY

Turn the selector band to “Filtered Spray” when

cleaning fruits and vegetables.

NOTE: You do not have to hold the cap to continue receiving

filtered water.

FILTERED STREAM

Turn the selector band to “Filtered Stream” when you

are filling a glass of water or using water for cooking.

NONFILTERED WATER

If you turn on the faucet but do not turn the selector band,

you will receive unfiltered water through your faucet.

WARNING — Do not attempt to filter hot water

above 100°F (37.7°C). It will damage the filter cartridge and

decrease performance.

NOTE: If it is necessary to connect a portable dishwasher to

your faucet, simply unscrew the filter from the faucet and

attach the dishwasher according to the manufacturer’s

instructions.

Selector band

Selector indicator

Selector band

Selector indicator

Green light

Installation Instructions

BATTERY REPLACEMENT

Turn off the water to the filtration system.

Remove the cap of the filtration system by

inserting a small coin or screwdriver on the back

of the system and pry to remove cap.

See Steps 4–8 in the Initial Set-Up section for

proper battery replacement instructions.

3

2

1

INDICATOR LIGHT

The Faucet Mount FIlter is equipped with indicator

lights that tell you when it is time to change the filter

and battery.

The amber light will flash one time every few seconds

to remind you that it is time to change the filter.

The amber light will flash three quick flashes every

few seconds when it is time to change the battery

and filter.

Green light

flashes to

indicate you

are using

Filtered

Spray.

Green light flashes to

indicate you are using

Filtered Stream.

Amber light indicates it is time

to change the filter and/or

battery.

4

FILTER CARTRIDGE REPLACEMENT

Turn off the water to the filtration system.

Remove the cap of the filtration system by

inserting a small coin or screwdriver on the back

of the system and pry to remove cap.

Remove the old filter cartridge by turning

counterclockwise. Be sure to support the faucet

and the filter housing during the filter removal

to avoid damage. Dispose of the old filter.

NOTE: Some water may drip from the system

during filter cartridge removal.

3

2

1

Turn filter

counterclockwise

to remove.

Insert a small coin

or screwdriver on

the back and pry

to remove cap.

Insert a small coin

or screwdriver on

the back and pry

to remove cap.

FILTER CARTRIDGE REPLACEMENT (CONT.)

Remove the packaging and label at the bottom

of the new filter. Then install the new filter. Be

sure to support the filter housing in your hand

and press the new filter into the housing firmly,

then turn the filter clockwise until hand-tight.

Continue to turn until the tab lines up with the

non-filtered icon as shown below:

Align the cap with the filter housing (lights in the

front) and press it down into place.

NOTE: The cap is designed to fit on the filter housing only

one way

.

Slowly turn on the water supply and check

for leaks.

NOTE: If leak occurs at filter, turn cartridge to

make sure it is fully sealed.

With the cold water fully open, turn the selector

dial to “Filtered Water” to begin flushing the

system. Flush the new filter cartridge for

10 minutes to remove any harmless carbon

fines that may be in the system.

7

6

5

4

Twist filter

clockwise

to install.

Tab on filter

will line up

with the

Non-filtered

icon when the

filter is fully

installed.

State of California

Department of Public Health

Water Treatment Device

Certificate Number

Date Issued: March 17, 2008

Trademark/Model Designation

Replacement Elements

189408

-

HLMXFLBH70MFXG

HLMXFWWH70MFXG

Manufacturer:

General Electric Company

The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section

116830 of the Health and Safety Code for the following health related contaminants:

daeLstsyC

Mercury

Benzene

Carbofuran

Lindane

P-Dichlorobenzene

Toxaphene

Microbiological Contaminants and Turbidity

Inorganic/Radiological Contaminants

Organic Contaminants

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified

for cyst reduction may be used on disinfected waters that may contain filterable cysts.

75 gals

Rated Service Capacity:

0.6 gpm

Rated Service Flow:

Conditions of Certification:

Installation Instructions

5

CLEANING THE SYSTEM

Use a damp cloth and mild soap for cleaning. Do not

use harsh chemicals, detergents, abrasives, solvents

or cleaning fluids, since they will damage the filtration

system.

REPLACEMENT FILTER CARTRIDGES/

ESTIMATED REPLACEMENT COSTS

FXMLH—Replacement filter cartridge $28–$33

For replacement parts, call toll-free 800.626.2002 (U.S.),

800.663.6060 (Canada-English), 800.361.3869

(Canada-French).

Iowa Residents Only:

_________________________________________________________

Store or Seller’s name

_________________________________________________________

Address

_________________________________________________________

City State Zip

_________________________________________________________

Telephone

_________________________________________________________

Seller’s signature

_________________________________________________________

Customer’s signature Date

Problem Possible Causes What To Do

Faucet leaking Missing gasket in tightening nut. • Use Teflon Tape on faucet threads.

Swivel collar not tight enough. • Tighten the swivel collar.

Gasket not seated in the swivel • Make sure gasket is seated in the swivel collar, then tighten the

collar. swivel collar.

Filter cartridge housing Missing O-ring on replacement • Return to the store.

fits loosely to the base filter.

Can not tighten the filter Extra O-ring in housing. • Remove the O-ring from the housing (not from the filter).

cartridge

TROUBLESHOOTING TIPS

6

LIMITED ONE-YEAR WARRANTY

• What does this warranty cover?

– Any defect in materials or workmanship in the manufactured product

• What does this warranty not cover?

– Filter Cartridges

– Service trips to your home to teach you how to use the product

– Improper installation

– Failure of the product if it is abused, misused, altered or used for other than

the intended purpose

– Defects that result from improper installation or damage not caused by GE

– Liability on the part of GE under this or any other warranty for any indirect

or consequential damage

– Products that are used for commercial or industrial applications

– Use of this product where water is microbiologically unsafe or of unknown quality,

without adequate disinfection before or after the system. Systems certified for cyst

reduction may be used on disinfected water that may contain filterable cysts.

– Damage to the product caused by accident, fire, floods or acts of God

– Incidental or consequential damage caused by possible defects with

this appliance, its installation or repair

• For how long after the original purchase?

–One Year

• How do I make a warranty claim?

– Return to the retailer from which it was purchased along with a copy

of the “Proof of Purchase.” This warranty excludes the cost of shipping

or service calls to your home.

• How does state law relate to this warranty?

– This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state. THIS WARRANTY IS INTENDED TO BE IN LIEU

OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Contact us at GEAppliances.com, or call 800.GE.CARES (U.S.), or toll-free 866.777.7627

(Canada).

Installation Instructions

PERFORMANCE DATA

GE GXFM07HBL AND GXFM07HWW WITH

FXMLH CARTRIDGE FAUCET MOUNT FILTRATION SYSTEM

This system has been tested according to NSF/ANSI 42 and 53 for reduction of the substances listed below.

The concentration of the indicated substances in water entering the system was reduced to a concentration

less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.

Average Max. Permissible

Influent Challenge Product Water Reduction Minimum Average

Substance Concentration Concentration Requirements Reduction Reduction

Standard 42

Aesthetic Chlorine 1.94 mg/L ≥ 50% 97.4%

Particulates 11,666,667 particles/mL ≥ 85% 99.9%

(0.5 to < 1 ∝m)

Class I

Standard 53

Cysts

2)

170,000/L 99.95% 99.99% 99.99%

Lead (6.5 pH) 0.14 mg/L 0.010 mg/L 99.3% 99.3%

Lead (8.5 pH) 0.15 mg/L 0.010 mg/L 99.3% 99.3%

Lindane 0.002 mg/L 0.0002 mg/L 98.0% 99.0%

Mercury (6.5 pH) 0.006 mg/L 0.002 mg/L 96.6% 96.6%

Mercury (8.5 pH) 0.005 mg/L 0.002 mg/L 77.4% 89.7%

Benzene 0.015 mg/L 0.005 mg/L 96.6% 96.6%

Carbofuran 0.08 mg/L 0.04 mg/L 97.6% 98.7%

P-Dichlorobenzene 0.225 mg/L 0.075 mg/L 99.8% 99.8%

Toxaphene 0.015 mg/L 0.003 mg/L 93.2% 93.2%

2) Based on the use of live cysts.

Testing was performed under standard laboratory conditions; actual performance may vary.

NOTE: Substances reduced are not necessarily in your water. Filter must be maintained according to manufacturer’s

instructions, including replacement of filter cartridges.

WARNING — Do not use with water that is microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system. Systems certified for cyst reduction may be used on

disinfected waters that contain filterable cysts.

Test Conditions: Operating Requirements:

• Flow Rate: 0.6 gpm (2.3 Lpm) • Service Flow Rate: 0.6 gpm (2.3 Lpm)

• Inlet Pressure: 60 psi (4.1 bar) • Rated Service Life: 75 gallons (284 liters)

• pH of 7.5±1 • Pressure: 30–125 psi (2.1–8.6 bar/kglcm2)

• Temp of 50°–77°F (10°–25°C) • Temperature: 40°–100°F (4.4°–37.7°C)

Page is loading ...

GE GXFM07HBL User manual

This manual is also suitable for

GE GXFM07HBL User manual

in other languages

Related papers

Other documents