Allied Telesis x600-48Ts/XP User manual

613-001065 Rev. A

x600 Series

Layer 3 Gigabit

Ethernet Switches

x600-24Ts

x600-24Ts/XP

x600-48Ts

x600-48Ts/XP

◆

Installation Guide

Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or

other designations mentioned herein are trademarks or registered trademarks of their respective owners.

Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior

written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any

incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this

manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of

such damages.

3

Electrical Safety and Emissions Standards

This product meets the following standards.

RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, VCCI

Class A, C-TICK, CE

EMC (Immunity) EN55024

Electrical Safety EN60950-1 (TUV), EN60825-1 (TUV), UL 60950-1 (

C

UL

US

), CSA-C22-2

No. 60950-1 (

C

UL

US

)

U.S. Federal Communications Commission

Radiated Energy

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15

of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate

this equipment.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Laser Safety EN60825

4

Translated Safety Statements

Important: The  indicates that a translation of the safety statement is available in a document

entitled Translated Safety Statements for the x600 Series Layer 3 Gigabit Ethernet Switches (613-

000990).

5

Contents

Preface .............................................................................................................................................................. 7

Product Documentation ...................................................................................................................................... 8

Starting a Management Session ........................................................................................................................ 9

Safety Symbols Used in this Document ........................................................................................................... 10

Where to Find Web-based Guides ................................................................................................................... 11

Contacting Allied Telesis .................................................................................................................................. 12

Online Support ........................................................................................................................................... 12

Email and Telephone Support.................................................................................................................... 12

Warranty..................................................................................................................................................... 12

Returning Products .................................................................................................................................... 12

Sales or Corporate Information .................................................................................................................. 12

Management Software Updates................................................................................................................. 12

Chapter 1: Overview ...................................................................................................................................... 13

Introduction....................................................................................................................................................... 14

Switch Descriptions .......................................................................................................................................... 15

x600-24Ts Switch....................................................................................................................................... 15

x600-24Ts/XP Switch................................................................................................................................. 16

x600-48Ts Switch....................................................................................................................................... 17

x600-48Ts/XP Switch................................................................................................................................. 18

10/100/1000Base-T Twisted Pair Ports............................................................................................................ 19

Connector Type.......................................................................................................................................... 19

Speed......................................................................................................................................................... 19

Duplex Mode .............................................................................................................................................. 19

Maximum Distance..................................................................................................................................... 19

Cable Type................................................................................................................................................. 20

Auto-MDI/MDI-X......................................................................................................................................... 20

Port Pinouts................................................................................................................................................ 20

SFP Transceiver Slots...................................................................................................................................... 21

XFP Transceiver Slots...................................................................................................................................... 22

Redundant Twisted Pair Ports.......................................................................................................................... 23

SD Card Slot..................................................................................................................................................... 24

Port LEDs ......................................................................................................................................................... 25

10/100/1000Base-T Twisted Pair Port LEDs ............................................................................................. 25

SFP LEDs .................................................................................................................................................. 26

XFP Transceiver Slot LEDs ....................................................................................................................... 26

System LEDs.................................................................................................................................................... 27

Stack LEDs....................................................................................................................................................... 28

Secure Digital LEDs ......................................................................................................................................... 29

Terminal Port .................................................................................................................................................... 30

AT-RPS3204 Redundant Power Supply........................................................................................................... 31

AT-LBM Module................................................................................................................................................ 32

AC Power Connector........................................................................................................................................ 33

Chapter 2: Installing the Hardware .............................................................................................................. 35

Reviewing Safety Precautions.......................................................................................................................... 36

Contents

6

Unpacking a Switch .......................................................................................................................................... 38

Installing the Power Cord Retaining Clip ..........................................................................................................39

Installing the Switches in an Equipment Rack ..................................................................................................40

Resetting the Switch .........................................................................................................................................42

Chapter 3: Cabling the Network Ports .........................................................................................................43

Twisted Pair and Fiber Optic Cable Specifications ...........................................................................................44

Twisted Pair Cable Specifications ..............................................................................................................44

Optional Transceiver Cable Specifications.................................................................................................45

Installing Optional Transceivers ........................................................................................................................46

Installing an SFP Transceiver.....................................................................................................................46

Installing an XFP Transceiver.....................................................................................................................49

Cabling the Twisted Pair and Fiber Optic Ports ................................................................................................51

Powering on a Switch ....................................................................................................................................... 52

Starting a Local Management Session.......................................................................................................53

Warranty Registration ....................................................................................................................................... 54

Chapter 4: Troubleshooting .......................................................................................................................... 55

Power LED is Off .............................................................................................................................................. 56

Twisted Pair Port Link LED is Off......................................................................................................................57

SFP or XFP LED is Off ..................................................................................................................................... 58

Transceiver is Installed but the Status is “Not Present” .................................................................................... 59

System Fault LED is Blinking ............................................................................................................................60

System Fault LED is Steadily On ......................................................................................................................61

Cannot Establish a Local (Out-of-Band) Management Session........................................................................ 62

Switch Functions Intermittently .........................................................................................................................63

Appendix A: Technical Specifications .........................................................................................................65

Physical Specifications .....................................................................................................................................65

Environmental Specifications ............................................................................................................................65

Power Specifications......................................................................................................................................... 66

Certifications .....................................................................................................................................................66

RJ-45 Twisted Pair Port Pinouts ....................................................................................................................... 67

RJ-45 Style Serial Terminal Port Pinouts..........................................................................................................69

RPS 21-pin D-combo Port and Connector Pinouts...........................................................................................70

7

Preface

This guide contains the installation instructions for the x600 Series Layer 3

Gigabit Ethernet Switches. This preface contains the following sections:

 “Product Documentation” on page 8

 “Starting a Management Session” on page 9

 “Safety Symbols Used in this Document” on page 10

 “Where to Find Web-based Guides” on page 11

 “Contacting Allied Telesis” on page 12

Preface

8

Product Documentation

For overview information about the software features of the AlliedWare

Plus

TM

Operating System Software which runs on the x600 Series

Switches, refer to:

 AlliedWare Plus

TM

Operating System Software Reference Guide

x600 Layer 3 Gigabit Ethernet Switch Installation Guide

9

Starting a Management Session

For instructions that describe how to start a local management session on

an x600 switch, refer to the “Starting a Local Management Session” on

page 53. For information that describes how to log onto the AlliedPlus

TM

Operating System Software, see the AlliedWare Plus

TM

Operating System

Software Reference Guide.

Preface

10

Safety Symbols Used in this Document

This document uses the safety symbols defined in Table 1.

Table 1. Safety Symbols

Symbol Meaning Description

Caution Performing or omitting a specific action may

result in equipment damage or loss of data.

Warning Performing or omitting a specific action may

result in electrical shock.

x600 Layer 3 Gigabit Ethernet Switch Installation Guide

11

Where to Find Web-based Guides

The installation and user guides for all Allied Telesis products are available

in portable document format (PDF) on our web site at

www.alliedtelesis.com. You can view the documents online or download

them onto a local workstation or server.

Preface

12

Contacting Allied Telesis

This section provides Allied Telesis contact information for technical

support as well as sales and corporate information.

Online Support You can request technical support online by accessing the Allied Telesis

Knowledge Base: www.alliedtelesis.com/support/kb.aspx. You can use

the Knowledge Base to submit questions to our technical support staff and

review answers to previously asked questions.

Email and

Telephone

Support

For Technical Support via email or telephone, refer to the Support section

of the Allied Telesis web site: www.alliedtelesis.com.

Warranty The x600 Series Layer 3 Gigabit Ethernet Switches are covered under a

Lifetime Warranty (Two Years Fan & Power Supply). For warranty

information, go to the Allied Telesis web site at www.alliedtelesis.com.

Returning

Products

Products for return or repair must first be assigned a return materials

authorization (RMA) number. A product sent to Allied Telesis without an

RMA number will be returned to the sender at the sender’s expense. For

instructions on how to obtain an RMA number, go to the Support section

on our web site at www.alliedtelesis.com.

Sales or

Corporate

Information

You can contact Allied Telesis for sales or corporate information through

our web site at www.alliedtelesis.com.

Management

Software Updates

New releases of the management software for our managed products are

available from the following Internet sites:

 Allied Telesis web site: www.alliedtelesis.com

 Allied Telesis FTP server: ftp://ftp.alliedtelesis.com

If the FTP server prompts you to log on, enter “anonymous” as the user

name and your email address as the password.

13

Chapter 1

Overview

This chapter contains the following sections:

 “Introduction” on page 14

 “Switch Descriptions” on page 15

 “10/100/1000Base-T Twisted Pair Ports” on page 19

 “SFP Transceiver Slots” on page 21

 “XFP Transceiver Slots” on page 22

 “Redundant Twisted Pair Ports” on page 23

 “SD Card Slot” on page 24

 “Port LEDs” on page 25

 “System LEDs” on page 27

 “Stack LEDs” on page 28

 “Terminal Port” on page 30

 “Secure Digital LEDs” on page 29

 “AT-RPS3204 Redundant Power Supply” on page 31

 “AT-LBM Module” on page 32

 “AC Power Connector” on page 33

Note

Do not begin the installation procedures in this guide until you have

read the AlliedWare Plus

TM

Operating System Software Release

Notes that are included with the latest release of the AlliedWare

Plus

TM

Operating System Software.

Chapter 1: Overview

14

Introduction

The x600 Series Switches are managed Gigabit Ethernet switches that

acts as standalone units. There are four Basic Layer 3 switches in the

series:

 x600-24Ts Switch

 x600-24Ts/XP Switch

 x600-48Ts Switch

 x600-48Ts/XP Switch

The x600-24Ts and the x600-24Ts/XP switches both have 24

10/100/1000Base-T ports. The x600-48Ts and the x600-48Ts/XP switches

both have 44 10/100/1000 Base-T ports.

All four switches have four SFP transceiver slots, an Secure Digital (SD)

card slot, a console port, and a redundant power supply connector. In

addition, the x600-24Ts/XP and the x600-48Ts/XP switches have two XFP

transceiver slots.

On the back of all the switches there is an AC power connector, an RPS

connector, and an expansion slot. You can connect the RPS connector to

the AT-RPS3204 Redundant Power Supply. The x600 switches are

shipped with a blank expansion slot with the exception of the The x600-

48Ts/XP switch which is shipped with an AT-LBM (Link Back Mode)

Module installed in the expansion slot.

The AlliedWare Plus

TM

Operating System Software runs on all the x600

switches.

For more detailed information about the switches, including illustrations,

see “Switch Descriptions” on page 15.

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide

15

Switch Descriptions

The following sections describe the x600-24Ts, x600-24Ts/XP,

x600-48Ts, x600-48Ts/XP Series Layer 3 Gigabit Ethernet Switches.

x600-24Ts Switch The x600-24Ts switch has the following hardware features:

 24 10/100/1000Base-T ports

 Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver

slots

 An RJ-45 style serial terminal port for local (out-of-band) management

 One SD slot supporting 512KB and 1GB SD cards

 Status LEDs for the ports, transceiver slots, and system

 Redundant power supply connector

 Expansion slot for the AT-StackXG Stacking Module

Figure 1 shows the front panel of the x600-24Ts switch. Figure 2 shows

the back panel of the x600-24Ts switch.

Figure 1. x600-24Ts Switch— Front Panel

Figure 2. x600-24Ts Switch— Back Panel

1 3 5 7 9 11 13 15 17 19 21R 23R

2 4 6 8 10 12 14 16 18 20 22R 24R

x600-24Ts

Layer 3 Gigabit Ethernet Switch

CLASS 1

LASER PRODUCT

D/C

L/A

1000 LINK / ACT

HDX /

COL

FDX

10/100 LINK / ACT

PORT ACTIVITY

L/A

D/C

L/AL/A

STACK

PRES

MSTR

L/A

1

2

SFP

21 22

23 24

1 3 5 7 9 11 13 15 17 19 21R 23R

2 4 6 8 10 12 14 16 18 20 22R 24R

FAU LT

RPS

MASTER

PWR

STATUS

21

22

23

24

SFP

L/A

BUSY

READY

FAULT

SD

RESET

CONSOLE

1329

10/100/1000Base-T Ports

Port, SFP, and SD

Slot LEDs

System

LEDs

SFP Transceiver Slots

RJ-45 Style Serial

Terminal Port

AC Power

Connector

RPS Connector

Expansion Slot

RPS INPUT

100-240VAC~

1310

Chapter 1: Overview

16

x600-24Ts/XP

Switch

The x600-24Ts/XP switch has the following hardware features:

 24 10/100/1000Base-T ports

 Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver

slots

 Two 10 Gigabit Ethernet small form factor pluggable (XFP) transceiver

slots

 An RJ-45 style serial terminal port for local (out-of-band) management

 One SD slot supporting 512KB and 1GB SD cards

 Status LEDs for the ports, transceiver slots, and system

 Redundant power supply connector

 Expansion slot for the AT-StackXG Stacking Module

Figure 3 shows the front panel of the x600-24Ts/XP switch. Figure 4

shows the back panel of the x600-24Ts/XP switch.

Figure 3. x600-24Ts/XP Switch— Front Panel

Figure 4. x600-24Ts/XP Switch— Back Panel

1 3 5 7 9 11 13 15 17 19 21R 23R

2 4 6 8 10 12 14 16 18 20 22R 24R

x600-24Ts/XP

Layer 3 Gigabit Ethernet Switch

CLASS 1

LASER PRODUCT

D/C

L/A

1000 LINK / ACT

HDX /

COL

FDX

10/100 LINK / ACT

PORT ACTIVITY

2625

L/A

XFP XFP

L/A

D/C

L/AL/A

STACK

PRES

MSTR

L/A

1

2

SFP

21 22

23 24

1 3 5 7 9 11 13 15 17 19 21R 23R

2 4 6 8 10 12 14 16 18 20 22R 24R

FAU LT

RPS

MASTER

PWR

STATUS

21

22

23

24

SFP

L/A

BUSY

READY

FAULT

SD

RESET

CONSOLE

1307

10/100/1000Base-T Ports

SFP Slots XFP Slots

System

LEDs

RJ-45 Style Serial

Terminal Port

Port, SFP, and SD

Slot LEDs

AC Power

Connector

RPS Connector

Expansion Slot

RPS INPUT

100-240VAC~

1310

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide

17

x600-48Ts Switch The x600-48Ts switch has the following hardware features:

 44 10/100/1000Base-T ports

 Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver

slots

 An RJ-45 style serial terminal port for local (out-of-band) management

 One SD slot supporting 512KB and 1GB SD cards

 Status LEDs for the ports, transceiver slots, and system

 Redundant power supply connector

 Expansion slot for the AT-StackXG Stacking Module

Figure 5 shows the front panel of the x600-48Ts switch. Figure 6 shows

the back panel of the x600-48Ts switch.

Figure 5. x600-48Ts —Front Panel

Figure 6. x600-48Ts —Back Panel

FDX

HDX / COL

D/C

1000 LINK / ACT

10/100 LINK / ACT

L/A

L/A D/C

CLASS 1

LASER PRODUCT

15135791113 17 3331 473519 21 23 25 27 29 37 39 41 43 45

34

4836 38 40 42 44 46

3216

2 4 6 8 10 12 14 22 24 26 28 30

18

20

STATUS

FAULT

MASTER

RPS

PWR

PRES

MSTR

L/A

1

2

STACK

CONSOLE

L/A

SFP

x600-48Ts

BUSY

READY

FAULT

SD

RESET

Layer 3 Gigabit Ethernet Switch

1330

SD Card Slot

10/100/1000Base-T Ports and LEDs

SFP Slots

System LEDs

RJ-45 Style Serial

Terminal Port

AC Power

Connector

RPS Connector

Expansion Slot

RPS INPUT

100-240VAC~

1310

Chapter 1: Overview

18

x600-48Ts/XP

Switch

The x600-48Ts/XP switch has the following hardware features:

 44 10/100/1000Base-T ports

 Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver

slots

 Two 10 Gigabit Ethernet small form factor pluggable (XFP) transceiver

slots

 An RJ-45 style serial terminal port for local (out-of-band) management

 One SD slot supporting 512KB and 1GB SD cards

 Status LEDs for the ports, transceiver slots, and system

 Redundant power supply connector

 AT-LBM module installed in the back of the switch

Figure 7 shows the front panels of the x600-48Ts/XP switch. Figure 8

shows the back panel of the x600-48Ts/XP switch.

Figure 7. x600-48Ts/XP Switch —Front Panel

Figure 8. x600-48Ts/XP Switch —Back Panel

FDX

HDX / COL

D/C

1000 LINK / ACT

10/100 LINK / ACT

L/A

L/A D/C

L/A

49 50

XFP XFP

CLASS 1

LASER PRODUCT

LINK / ACT

15135791113 17 3331 473519 21 23 25 27 29 37 39 41 43 45

34

4836 38 40 42 44 46

3216

2 4 6 8 10 12 14 22 24 26 28 30

18

20

STATUS

FAULT

MASTER

RPS

PWR

PRES

MSTR

L/A

1

2

STACK

CONSOLE

L/A

SFP

x600-48Ts/XP

BUSY

READY

FAULT

SD

RESET

Layer 3 Gigabit Ethernet Switch

1308

10/100/1000Base-T Ports and LEDs

SD

Card Slot

XFP Slots

System LEDs

RJ-45 Style Serial

Terminal Port

SFP Slots

AC Power

Connector

RPS Connector

AT-LBM Module

RPS INPUT

100-240VAC~

AT-LBM

1309

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide

19

10/100/1000Base-T Twisted Pair Ports

This section describes the twisted pair ports on the switches.

Connector Type The ports are 8-pin RJ-45 connectors that use four pins at 10 or 100 Mbps

and all eight pins at 1000 Mbps. For the pin assignments, refer to “RJ-45

Twisted Pair Port Pinouts” on page 67.

Speed A port’s speed can be 10, 100, or 1000 Mbps. The speed can be set

automatically through Auto-Negotiation, the default setting, or manually

with the AlliedWare Plus

TM

Operating System Software.

Note

To operate at 1000 Mbps, a twisted pair port must be set to Auto -

Negotiation. The speed of a twisted pair port cannot be set manually

to 1000 Mbps.

Duplex Mode A twisted pair port can operate in either half- or full-duplex mode. (Full-

duplex mode is the only mode available when a port is operating at 1000

Mbps.) The twisted pair ports are IEEE 802.3u-compliant and Auto-

Negotiate the duplex mode setting.

You can disable Auto-Negotiation on one or all of the switch ports so that

you can set the duplex mode manually through the AlliedWare Plus

TM

Operating System Software.

Note

In order for a switch port to successfully Auto-Negotiate its duplex

mode with a 10 or 100 Mbps end node, the end node must be

configured for Auto-Negotiation. Otherwise, a duplex mode

mismatch can occur. A switch port using Auto-Negotiation defaults

to half-duplex if it detects that the end node is not using Auto-

Negotiation. This results in a mismatch if the end node is operating

at a fixed duplex mode of full-duplex.

To avoid this problem when connecting an end node with a fixed

duplex mode of full-duplex to a switch port, use the AlliedWare

Plus

TM

Operating System Software to disable Auto-Negotiation on

the port and set the port speed and duplex mode manually.

Maximum

Distance

The ports have a maximum operating distance of 100 meters (328 feet).

Chapter 1: Overview

20

Cable Type The cabling requirements for a 10/100/1000Base-T port are:

 For 10 Mbps operation: Standard TIA/EIA 568-B-compliant Category 3

or better shielded or unshielded cabling with 100 ohm impedance and

a frequency of 16 MHz.

 For 100 Mbps operation: Standard TIA/EIA 568-A-compliant Category

5 or TIA/EIA 568-B-compliant Enhanced Category 5 (Cat 5e) shielded

or unshielded cabling with 100 ohm impedance and a frequency of 100

MHz.

 For 1000 Mbps operation: Standard TIA/EIA 568-A-compliant

Category 5 or TIA/EIA 568-B-compliant Enhanced Category 5 (Cat 5e)

shielded or unshielded cabling with 100 ohm impedance and a

frequency of 100 MHz.

Auto-MDI/

MDI-X

The twisted pair ports on the switch are IEEE 802ab-compliant and feature

auto-MDI/MDI-X. This feature, available when a port’s speed and duplex

mode are set through Auto-Negotiation, automatically configures a switch

port to MDI or MDI-X depending on the wiring configuration of the port on

the end node. This allows you to connect any network device to a port on

the switch using a straight-through twisted pair cable.

If Auto-Negotiation is disabled on a port and the speed and duplex mode

are set manually, the auto-MDI/MDI-X feature is also disabled and the

port’s wiring configuration defaults to the MDI-X setting. This setting can

be configured with the AlliedWare Plus

TM

Operating System Software.

Port Pinouts Refer to Table 10 on page 67 for the port pinouts when a twisted pair port

operates at 10 or 100 Mbps in the MDI configuration and Table 11 on

page 67 for the MDI-X configuration. For port pinouts when a twisted pair

port operates at 1000 Mbps, refer to Table 12 on page 68.

Page is loading ...

Allied Telesis x600-48Ts/XP User manual

Allied Telesis x600-48Ts/XP User manual

Related papers

Other documents