American Standard M968656 User manual

Category
Sanitary ware
Type
User manual

American Standard M968656 is a diverter trim kit that can be used to control the flow of water in your shower or bathtub. It is designed to be easy to install and maintain, and it comes with a variety of features that make it a great choice for any bathroom.

Some of the key features of the American Standard M968656 include:

  • Certified to comply with ANSI A112.18.1 This means that the trim kit has been tested and certified to meet the highest standards of quality and performance.
  • Escutcheon and escutcheon holder The escutcheon is the decorative plate that covers the hole in the wall where the trim kit is installed. The escutcheon holder is the part that attaches the escutcheon to the wall.

American Standard M968656 is a diverter trim kit that can be used to control the flow of water in your shower or bathtub. It is designed to be easy to install and maintain, and it comes with a variety of features that make it a great choice for any bathroom.

Some of the key features of the American Standard M968656 include:

  • Certified to comply with ANSI A112.18.1 This means that the trim kit has been tested and certified to meet the highest standards of quality and performance.
  • Escutcheon and escutcheon holder The escutcheon is the decorative plate that covers the hole in the wall where the trim kit is installed. The escutcheon holder is the part that attaches the escutcheon to the wall.
DIVERTER TRIM KIT
Installation
Instructions
M 9 6 8 6 5 6
M 9 6 8 6 5 6 M 9 6 8 6 5 6
T555430
TOWNSQUARE
DIVERTER TRIM KIT
TOWNSQUARE
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
MODEL NUMBERS
OPERATING THE VALVE
OFF
1
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Align ESCUTCHEON (1). Thread ESCUTCHEON HOLDER (2) onto DIRVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against fiished wall.
TRIM INSTALLATION
1
2
3
2
HANDLE INSTALLATION
Push HANDLE ADAPTER (1) onto VALVE STEM (2).
Turn VALVE STEM (2) to off position.
Push HANDLE ASSEMBLY (3) onto HANDLE ADAPTER (1).
In stall HANDLE SCREW (4) and tighten.
Push INDEX BUTTON (5) into HANDLE ASSEMBLY (3).
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
lm and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
3
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uc t na me s li st ed h er ei n ar e tr ad em ar ks o f Am er ic an S ta nd ar d In c.
© AS A me ri ca , In c. 2 00 8
IN MEXICO 01-800-839-12-00
Turn water supply on and test installed fitting.
Rotate handle to all diverter positions to check operation of valve.
Check for leaks.
M962640-YYY0A
ESCUTCHEON KIT
954027-YYY0A
ESCUTCHEON HOLDER
M918043-0070A
HANDLE ADAPTER
M908572-YYY0A
HANDLE BASE
A918555-0070A
HANDLE SCREW
M907024-YYY0A
INDEX BUTTON
FINISHED
WALL
FINISHED
WALL
41mm MIN.
(1-5/8)
66mm MAX.
(2-5/8)
71mm
(2-3/4)
57mm HOLE SIZE
(2-1/4)
75mm
(2-7/8)
2
1
3
4
5
M916814-YYY420A
LEVER
T555430
CHROME
BLACKENED BRONZE
SATIN NICKEL
002
068
295
Replace the "YYY" with
appropriate finish code
DIVERTER TRIM KIT
Installation
Instructions
M 9 6 8 6 5 6
M 9 6 8 6 5 6 M 9 6 8 6 5 6
T555430
TOWNSQUARE
DIVERTER TRIM KIT
TOWNSQUARE
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
MODEL NUMBERS
OPERATING THE VALVE
OFF
1
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Align ESCUTCHEON (1). Thread ESCUTCHEON HOLDER (2) onto DIRVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against fiished wall.
TRIM INSTALLATION
1
2
3
2
HANDLE INSTALLATION
Push HANDLE ADAPTER (1) onto VALVE STEM (2).
Turn VALVE STEM (2) to off position.
Push HANDLE ASSEMBLY (3) onto HANDLE ADAPTER (1).
In stall HANDLE SCREW (4) and tighten.
Push INDEX BUTTON (5) into HANDLE ASSEMBLY (3).
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
lm and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
3
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uc t na me s li st ed h er ei n ar e tr ad em ar ks o f Am er ic an S ta nd ar d In c.
© AS A me ri ca , In c. 2 00 8
IN MEXICO 01-800-839-12-00
Turn water supply on and test installed fitting.
Rotate handle to all diverter positions to check operation of valve.
Check for leaks.
M962640-YYY0A
ESCUTCHEON KIT
954027-YYY0A
ESCUTCHEON HOLDER
M918043-0070A
HANDLE ADAPTER
M908572-YYY0A
HANDLE BASE
A918555-0070A
HANDLE SCREW
M907024-YYY0A
INDEX BUTTON
FINISHED
WALL
FINISHED
WALL
41mm MIN.
(1-5/8)
66mm MAX.
(2-5/8)
71mm
(2-3/4)
57mm HOLE SIZE
(2-1/4)
75mm
(2-7/8)
2
1
3
4
5
M916814-YYY420A
LEVER
T555430
CHROME
BLACKENED BRONZE
SATIN NICKEL
002
068
295
Replace the "YYY" with
appropriate finish code
DIVERTER TRIM KIT
Installation
Instructions
M 9 6 8 6 5 6
M 9 6 8 6 5 6 M 9 6 8 6 5 6
T555430
TOWNSQUARE
DIVERTER TRIM KIT
TOWNSQUARE
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
MODEL NUMBERS
OPERATING THE VALVE
OFF
1
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Align ESCUTCHEON (1). Thread ESCUTCHEON HOLDER (2) onto DIRVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against fiished wall.
TRIM INSTALLATION
1
2
3
2
HANDLE INSTALLATION
Push HANDLE ADAPTER (1) onto VALVE STEM (2).
Turn VALVE STEM (2) to off position.
Push HANDLE ASSEMBLY (3) onto HANDLE ADAPTER (1).
In stall HANDLE SCREW (4) and tighten.
Push INDEX BUTTON (5) into HANDLE ASSEMBLY (3).
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
lm and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
3
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uc t na me s li st ed h er ei n ar e tr ad em ar ks o f Am er ic an S ta nd ar d In c.
© AS A me ri ca , In c. 2 00 8
IN MEXICO 01-800-839-12-00
Turn water supply on and test installed fitting.
Rotate handle to all diverter positions to check operation of valve.
Check for leaks.
M962640-YYY0A
ESCUTCHEON KIT
954027-YYY0A
ESCUTCHEON HOLDER
M918043-0070A
HANDLE ADAPTER
M908572-YYY0A
HANDLE BASE
A918555-0070A
HANDLE SCREW
M907024-YYY0A
INDEX BUTTON
FINISHED
WALL
FINISHED
WALL
41mm MIN.
(1-5/8)
66mm MAX.
(2-5/8)
71mm
(2-3/4)
57mm HOLE SIZE
(2-1/4)
75mm
(2-7/8)
2
1
3
4
5
M916814-YYY420A
LEVER
T555430
CHROME
BLACKENED BRONZE
SATIN NICKEL
002
068
295
Replace the "YYY" with
appropriate finish code
1 / 1

American Standard M968656 User manual

Category
Sanitary ware
Type
User manual

American Standard M968656 is a diverter trim kit that can be used to control the flow of water in your shower or bathtub. It is designed to be easy to install and maintain, and it comes with a variety of features that make it a great choice for any bathroom.

Some of the key features of the American Standard M968656 include:

  • Certified to comply with ANSI A112.18.1 This means that the trim kit has been tested and certified to meet the highest standards of quality and performance.
  • Escutcheon and escutcheon holder The escutcheon is the decorative plate that covers the hole in the wall where the trim kit is installed. The escutcheon holder is the part that attaches the escutcheon to the wall.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document