LW 10 1/1
ELT
Par N°
Label
Description
Masurem
ent unit
Default
A
Min Max
1 GAS
Define if the oven is GAS heated (1) or
ELECTRIC heated (0) 0 0 1
Type of oven:
0: LW 6 1/1
1: LW 10 1/1
2: LW 20 1/1
3: LW 10 2/1
4: LW 20 2/1
Languages:
0 = English
1 = Italian
2 = German
3 = French
4 = Spanish
5 = Dutch
6 = Swedish
7 = Danish
8 = Portuguese
9 = Greek
10 = Finnish
11 = Norwegian
12 = Estonian
13 = Lithuanian
14 = Latvian
15 = Polish
16 = Czech
17 = Slovakian
18 = Slovenian
19 = Hungarian
Temperature unit
0 = Celsius; 1= Fahrenheit
Flag to define the time format
0 = 24h; 1 = 12h AM/PM
Flag to enable cavity temperature
displaying adjustment
0 = Disable; 1 = Enable
Presence of lambda probe
0 = Not installed; 1 = Installed
0
0
3003 LAnG
05 C12H
7 LAMb 1 0 1
cort 0
0 0 1
0 1Nota1
Electrolux Air-O-Speed Oven: Parameter List firmware 130
Range regolaz.
4 FAHr
6
1
0 42 APPM 0 1
Type of meat probe
0 = Singlepoint; 1 = Multipoint
Power supply type:
0 = with neutral; 1 = without neutral
Flag to disable the automatic cleaning
cycles
0 = Enable; 1 = Disable
12 FCLn
Mandatory cleaning minutes countdown
counter min 0 -120 120
13 PAUt
Flag to enable automatic program (clean
excluded) 1 0 1
Starting environment after oven switch on
0: MANUAL
1: AUTOMATIC
2: PROGRAM
Flag manual humidifier
0 = Disable; 1 = Enable
Flag that enables infrared communication
0 = Disable; 1 = Enable
17 PHMN
Flag to enable the cavity preheating in
manual mode 1 0 1
Flag to enable Peak Power Management
0 = Not active; 1 = Active
Flag to enable the DEMO mode.
0 = Not active; 1 = active
Flag to disable the oven stops when door
is open in convection and combi mode
0 = Disable; 1 = Enable
Flag to enable starting of cooking closing
the door
0 = Disable; 1 = Enable
Flag to enable the changing from
automatic to manual mode
0 = Disable; 1 = Enable
14 MODO
1
122 Hdut Flag to enable heaters duty-cycle
0
11 0
1
0 0
1
0 1
0
0
2
1
0
19 0
Flag to enable the detergent and rinse aid
external tanks level sensors
0
0
18 PPM 0
1
0
23 AbAM
dEMO
11 ALIE
0 110 dCLn 0
0 120 0
6Prb 1
0
15 MHUM
8
9 NO N 0 Nota2 0 1
0 1
16 IrdA
21 AbSP
dSod
0 11
Flag to disable preheating of boiler of
boiler when the oven is in stand-by mode
0 = Disable; 1 = Enable
°C 85 0 100
°F 185 32 212
°C 35 0 55
°F 95 32 131
°C 90 50 300
°F 194 122 572
°C 80 50 100
°F 176 122 212
°C 250 0 300
°F 482 32 572
°C 180 0 300
°F 356 32 572
°C 40 0 300
°F 104 32 572
°C 250 0 300
°F 482 32 572
33 dutM
Maximum length of a phase with cavity
temperature over tCMS min 20 1 900
34 HUon
ON phase of the humidifier with combi
cycle between 50 and 100 °C (122 and
212 °F) s/10 5 0 250
35 tbon
Timeout for water level probe alarm (0 =
disabled control) s 0 0 2400
36 hbol Boiler hour counter h/4 0 0 9999
37 dbon Delay for boiler drain h/4 1 0 999
°C 50 0 100
°F 122 32 212
39 dtSb
Delay for fast filling during opening of
boiler drain valve s 255 0 255
40 SEAL Altitude above sea level m 0 Note3 0 4000
tCMS
Maximum temperature for no limitation
on phase length
0
32
26 Sbc
Cooling temperature set for electronic
board ventilation
Steam condenser engagement in
"steam/boiler" mode in lev. B ovens
38 tcdb Max. water temperature for boiler drain
28 StbP
27 HAbP
Steam condenser engagement in "hot air"
mode (lev. B ovens) and all cycles (lev. A
ovens)
31 trMn
Defines the min. temperature for water
injection during cooling phase
29 thMA
Defines the max. temperature limit for the
manual injection of water
30 trMA
Defines the max. temperature for water
injection during cooling phase
24 dSPS 0 1
25 SPHb Preheating temperature of the boiler
°C 0 -10 10
°F 32 14 50
°C 100 80 110
°F 212 176 230
43 HbYP Max. humidity value to stop the boiler % 98 80 100
°C 97 0 130
°F 97 32 266
°C 115 0 150
°F 239 32 302
°C 320 250 340
°F 608 482 644
°C 125 90 200
°F 257 194 392
Activation of cavity motor thermal
protection
0 = No alarm;
1 = Upper motor;
2 = Lower motor;
3 = All motor
4 = Boiler water level probes error
Magnetron current failure threshold
0: no test magnetron
52 MWdu Magnetron test sequence phase duration s/10 100 0 250
53 cu
Parameter q of SCELOFF formula (fuzzy
logic) -1 -20 20
54 EMME
Parameter m of SCELOFF formula (fuzzy
logic) 27 0 50
51 MWTH
almg
44
50
SInC
OLbd 0
SPHF
Boiler temperature set for fermentation
cycle
Lambda probe calibration (dry point) only
level A.
A/5 20
OCA1 Nota4
76,29 V
0 0
0 200
0
7
999
41
-999
48 bot
Max. steam generator overheating (EtuB
alarm)
Offset of first cavity temperature probe
45
49 ALFn 0
SbyP
Bypass temperature with max. cooking
cavity steam temperature (calibration)
47 cot
Max. cooking chamber overheating (EtuC
alarm)
4
Boiler temperature that detects the
presence of scale
42
46
55 PI
Parameter p of SCELON formula (fuzzy
logic) 0 -40 40
56 I
Parameter i of SCELON formula (fuzzy
logic) 2 -10 10
57 dton
Max. cooking chamber temperature
derivative value to switch on heating
elements (fuzzy logic) -1 -20 0
58 dtoF
Max. cooking chamber temperature
derivative value to switch off heating
elements (fuzzy logic) 2 0 20
HACCP mode:
0 = None
1 = Basic
2 = Advanced
3 = Monitor
RS485 bit rate
0 = 1200 baud
1 = 2400 baud
2 = 4800 baud
3 = 9600 baud
4 = 19200 baud
5 = 57600 baud
6 = 115200
61 Addr RS485 address 1 1 250
Print frequency
(0 = no print).
63 hair Hot air hour counter h 0 0 9999
64 hStM Steam hour counter h 0 0 9999
65 hcMb Combi hour counter h 0 0 9999
66 hMW Microwave hour counter h/4 0 0 9999
PWM value at start of cavity burners
G20
G25
G30
GPL
PWM value at half power of cavity
burners
G20
G25
G30
GPL
100
0 250
10068 hAcA % 50 0
% 20
62 tPrn s 30
67 StcA
59 HCCP 0
0
0 6
0 3
60 bAud 3
PWM value at full power of cavity
burners
G20
G25
G30
GPL
PWM value at start of boiler burners
G20
G25
G30
GPL
PWM value at half power of boiler
burners
G20
G25
G30
GPL
PWM value at full power of boiler
burners
G20
G25
G30
GPL
73 CLt1
Length of detergent injection (phases A
and B). s/10 30 1 250
74 CLt2
Length of detergent+water injection
(phases A and B). s/10 20 1 250
75 CLt3
Length of rinse aid+water injection (phase
C). s/10 50 1 250
77 MANU Flag to enable manual mode 1 0 1
78 AUTO Flag to enable automatic mode 1 0 1
79 PRRD Flag to enable program reading 1 0 1
80 PRWR Flag to enable program writing 1 0 1
Define if the modification of store
program is disable
0 = Enable; 1= Disable
82 PFAC
Flag to enable factory program (clean
excluded) 1 0 1
76
72
CLt4 s/10 10
Length of water injection (phase
C).
Fubo 100
250
1000
1
0% 75
71 hAbo % 50
10070 Stbo % 20 0
10069 FucA % 75 0
81
nMod 0 0 1
83 chr1
Password character 1
32 Nota5 0 255
84 chr2
Password character 2
32 Nota5 0 255
85 chr3
Password character 3
32 Nota5 0 255
86 chr4
Password character 4
32 Nota5 0 255
87 chr5
Password character 5
32 Nota5 0 255
88 chr6
Password character 6
32 Nota5 0 255
89 chr7
Password character 7
32 Nota5 0 255
90 chr8
Password character 8
32 Nota5 0 255
91 dbFd Food database index 0 Nota2 0 9
Note 1: set this parameter to 1 after bypass calibration and cavity offset (parameter OCA1)
/
