Sterling 6506-33S Installation guide

Page is loading ...

Tools and Materials

Before You Begin

WARNING: Risk of serious injury. Damage prior to installation can result in glass shattering.

Inspect the glass and all parts for damage before installation.

WARNING: Risk of serious injury. Improper installation can result in glass shattering. Follow all

installation instructions.

NOTICE: Do not touch the edges of the tempered glass with tools or any other hard objects. Do not set

the unframed tempered glass directly on the ﬂoor or any hard surface.

WARNING: Risk of serious injury. Do not cut tempered glass. Tempered glass will shatter if cut.

WARNING: Risk of serious injury. Shower door and side panels can shatter. Regularly inspect the

glass and all parts for damage, missing, or loose parts.

WARNING: Risk of serious injury. Always wear safety glasses while cutting and drilling.

IMPORTANT! Leave this manual for the end user. Read these instructions before installing or using this

product.

WARNING: Risk of personal injury. Do not cut the tempered glass. If the glass is cut, the glass

will shatter and may cause personal injury.

IMPORTANT! This door is designed to accommodate walls that are less than 3/8″ (1 cm) out of plumb.

Verify the area the door will be attached to is within 3/8″ (1 cm) or better of plumb. The door may not

function properly if the wall is more than 3/8″ (1 cm) out of plumb.

Your new Sterling door can be installed with the door opening to either the right or left. Install the

door with the pivot side away from the showerhead for best results.

Before starting the installation, lay out and identify all of the parts. Inspect for damage.

During the installation, protect the ﬂoor of the shower with a drop cloth to avoid damage.

The shower receptor should be installed and prepared at this time, including ﬁnished wall materials.

Closely follow the instructions pertaining to the sealant application on the door. Sealing areas other

than those shown may cause leaking.

Two people should perform this installation.

Safety Glasses

Level

Caulk Gun

File

Knife

Miter Box

Plus:

Drop Cloth

Pencil & Felt

Tip Marker

Claw

Hammer

Tape

Measure

Masking

Tape

Silicone

Sealant

Center

Punch

Drill and

Assorted

Drill Bits

Miter Saw or Hacksaw with

32 Teeth per Inch Blade

Assorted

Screwdrivers

1034028-2-H 2 Sterling

Determine the Door Conﬁguration

IMPORTANT! Install the pivot side of the door on the side opposite the showerhead.

Determine whether the door will pivot on the right or left side.

Make sure the door can swing freely in the chosen conﬁguration.

Sterling 3 1034028-2-H

Parts Identiﬁcation

Filler Jam

Wall Jamb

Hinge Jamb

Hinge

Door Panel Assembly

Strike Jamb

Wall Jamb

Towel Bar

Bottom Seal

Bottom Track

Hinge Jamb Cap

Strike Jamb Cap

Wall Jamb Cap

Strike Side Wall Jamb

1034028-2-H 4 Sterling

1. Measure and Cut the Bottom Track

IMPORTANT! Risk of product damage. If your shower has a curve in the corners where they meet the

sidewalls, be sure to measure from wall to wall above the curves. Failure to measure above the curve or

angle could result in the bottom track being cut too short.

Carefully measure the width (distance D) of the ﬁnished opening.

Consult the chart below to determine whether or not your installation will need a ﬁller jamb.

Model # Dimension D Filler Jamb Required?

65**-30 27-1/2″ (69.9 cm) - 29-1/2″ (74.9 cm) Not needed

65**-30 29-1/2″ (74.9 cm) - 30-1/2″ (76.2 cm) Needed

65**-33 30-1/2″ (76.2 cm) - 32-1/2″ (82.6 cm) Not needed

65**-33 32-1/2″ (82.6 cm) - 33-1/2″ (85.1 cm) Needed

65**-36 33″ (83.8 cm) - 35″ (88.9 cm) Not needed

65**-36 35″ (88.9 cm) - 36″ (91.4 cm) Needed

65**-39 36-1/2″ (92.7 cm) - 38-1/2″ (97.8 cm) Not needed

65**-39 38-1/2″ (97.8 cm) - 39-1/2″ (100.3 cm) Needed

NOTE: If dimension ″D″ falls in a range that can be either with or without the ﬁller jamb, use the ﬁller

jamb in your installation.

If your installation does not require a ﬁller jamb, subtract 2-3/4″ (7 cm) from dimension ″D″ and cut

the bottom track to this dimension. For best results, use a 32-teeth hacksaw blade and a miter box.

If your installation does require a ﬁller jamb, subtract 3-3/4″ (9.5 cm) from ″D″ and cut the bottom

track to this dimension. For best results, use a 32-teeth hacksaw blade and a miter box.

Important: Measure carefully. If your walls are

curved or angled, measure above the curve or

angle. Failure to do so can result in an improperly

cut bottom track.

Measure

here.

Measure

here.

Measure distance "D"

above curves in the

corners.

Angled

Base

Curved

Base

D

Bottom Track

Shower Ledge

Front Edge

Inside of Shower

Sterling 5 1034028-2-H

Measure and Cut the Bottom Track (cont.)

File the rough edges smooth where the bottom track was cut, taking care to avoid damaging

ﬁnished surfaces.

NOTE: If there are curves where the sidewalls meet the threshold, contour the wall jamb edges to match

the curves.

Locate the bottom track on the shower ledge. It should be located on the ﬂattest part of the ledge.

Position the bottom track so the gaps between the track and the wall are identical at both ends.

Make sure the bottom track is placed so it is an equal distance from the front edge of the shower

ledge at all points.

1034028-2-H 6 Sterling

2. Install the Adjustment Clamps

Insert four adjustment clamps into each wall jamb as shown (eight total).

Partially thread the provided #8-18 x 1/2″ panhead screws through the pre-drilled holes in the wall

jambs and into each adjustment clamp using a Phillips screwdriver. Do not tighten the screws at this

time.

Note:

Do not fully

tighten screw.

Adjustment Clamp

#8-18 x 1/2" Screw

Wall Jamb

Top View

Wall Jamb

#8-18 x 1/2" Screw

Sterling 7 1034028-2-H

3. Install the Wall Jambs and Optional Filler Jamb

Drill the Installation Holes

With a pencil, mark the location of the wall jamb on the shower wall. Measure evenly on both sides.

Place the wall jamb against the wall and check for plumb with a level. The side of the wall jamb

with the adjustment clamps attached to it should be located to the inside of the shower.

Make a pencil mark at each of the four pre-drilled holes in the wall jamb and remove the wall jamb.

NOTE: When installing on ceramic tile, use a center punch to nick the surface of the glaze. Tap the center

punch lightly with a hammer to avoid cracking the tile.

Drill each hole with a 5/16″ drill bit (use a masonry bit for ceramic tile).

Install the Anchors

Push (1) the middle of anchor in and fold (2) the outside edges down.

Insert (3) an anchor in each hole.

Repeat for all the anchors.

Install the Wall Jambs

If your installation requires a ﬁller jamb, position the ﬁller jamb over the holes.

Secure a wall jamb in place (over the ﬁller jamb if needed) using four provided panhead screws.

Repeat for the other wall jamb, skipping ﬁller jamb procedures.

Remove the bottom track and thoroughly clean the shower ledge.

Wall Jamb

Top View

Wall Jamb

#8-18 x 2"

Panhead Screw

Filler Jamb

With Filler Jamb

Without Filler Jamb

Anchor

Drill holes.

3

2

1

Adjustment Clamp

1034028-2-H 8 Sterling

4. Caulk and Install Bottom Track

Insert the bottom track and check for proper ﬁt. The lip of the bottom track should face toward the

outside of the shower. The ends of the bottom track should ﬁt snugly against the front protrusions

in the wall jambs.

Remove the bottom track and apply silicone sealant in the groove at the bottom front edge of the

bottom track.

Install the bottom track.

5. Assemble the Hinge Jamb

Lay the hinge jamb on the ﬂoor or on a workbench. Use a drop cloth to protect the product ﬁnish.

Insert the front side of the hinge into the slot on the hinge jamb.

Secure the hinge to the hinge jamb using four provided ﬂathead screws. Make sure the edge of the

hinge is ﬂush with the edge of the hinge jamb before tightening the screws.

Apply sealant.

Note:

Use silicone

tub & tile type caulk.

Bottom Track

Wall

Jamb

Flathead Screw

#8-18 x 1/2"

Hinge

Hinge Jamb

Insert the hinge

into the slot

making sure the

edges are flush.

Sterling 9 1034028-2-H

6. Install the Hinge to the Door Panel

NOTE: Leave a small gap on the handle side of the door for clearance from the strike jamb. The door will

not close properly without this gap.

Align the slotted holes on the hinge with the channel in the door panel. Make sure the top edge of

the hinge assembly is ﬂush with the top of the channel.

Secure the hinge to the door panel using four of the provided #10-16 x 3/8″ truss head screws.

Install the hinge jamb cap on the top of the hinge jamb where it aligns with edge of door.

Bottom Seal

Bottom View

Hinge Jamb Cap

Door Panel

Hinge Assembly

Hinge Jamb Cap

Hinge Jamb

Cap

Assemble, making sure

top edges are flush.

#10-16 x 3/8"

Truss Head Screw

1034028-2-H 10 Sterling

7. Install the Flat Seal

Slide the seal into the door panel seal holder with the fabric edge out.

Install the seal channel to the base of the door panel with the four provided #6-20 x 1/4″ panhead

screws.

Trim off any excess seal using a utility knife.

Pull out any fabric threads that jut out horizontally from the seal.

Fabric Seal

Seal Channel

Fabric Seal

Seal Channel

#6-20 x 1/4"

Panhead Screw

Pull out horizontal

threads.

Note:

Cut off excess

fabric seal length.

Sterling 11 1034028-2-H

8. Install the Strike Side Wall Jamb and Magnet

Push the strike jamb into the appropriate wall jamb with the wide lip facing toward the inside of

the shower. Each slot in the strike jamb will slide over the screw body and ﬁt between the clamp

and wall jamb.

Secure the strike jamb to the wall jamb by tightening the #8-18 x 1/2″ panhead screws in the

adjustment clamps until snug.

Install a strike jamb cap on the top opening of the strike jamb.

IMPORTANT! The strike jamb magnet is the longer of the two supplied magnets.

Install the strike jamb magnet to the contact surface of the strike jamb. The grooved side of the

magnet should face in.

Strike Jamb Cap

Strike Jamb

Wall Jamb

Adjustment

Clamp

Groove Side

of Magnet

Strike Jamb

Longest Magnet

Groove Side In

Magnet

Strike Jamb

1034028-2-H 12 Sterling

9. Install the Door Panel and Magnet

NOTE: You may need to loosen the clamp screws slightly to allow the wall jamb to ﬁt behind them.

Slide the hinge jamb into the other wall jamb. Each slot in the hinge jamb will slide over the screw

body and ﬁt between the clamp and wall jamb.

Tighten the four adjustment screws until snug.

IMPORTANT! The door panel magnet is the shorter of the two supplied magnets.

Install the provided magnet groove side out.

Use a pliers to crimp the bottom end of the door panel groove to secure the magnet.

Reverse for right hinge.

Hinge Jamb

Wall Jamb

Reverse Side

Door Panel

Assembly

If necessary, loosen clamp

screws slightly to fit wall

jamb behind clamps.

Shortest Magnet

Groove Side Out

Sterling 13 1034028-2-H

10. Adjust and Secure the Door

Adjust the door by loosening the jamb screws and shifting the assembly (maximum adjustment is

3/4″ (2 cm) on each side) as needed.

When each side of the door is uniformly aligned and the gap is evenly spaced between the wall

jambs, fully tighten the screws.

11. Install the Handle/Towel Bar

Slide the towel bar onto the towel bar brackets.

Position the towel bar seal on the bottom of the towel bar.

Secure the towel bar with the two provided screws.

Towel Bar

Assembly

Towel Bar Seal

Flathead Screw

#8-18 x 1-1/8"

Towel Bar

Bracket

Top View

Flathead Screw

#8-18 x 1-1/8"

1034028-2-H 14 Sterling

12. Caulk the Shower Door

NOTE: Follow the silicone sealant manufacturer’s curing instructions before using the shower.

Install the wall jamb caps to the tops of the wall jambs. Flat edges are toward the walls.

Apply silicone sealant to seams where the wall jambs and wall meet on both the outside and inside

of the shower.

Apply sealant to the outside of the shower where the bottom track meets the ﬂoor.

Apply sealant to the seam between the bottom track and the wall jamb.

Apply silicone sealant to the seams where the wall jambs and wall

meet on both the outside and inside of the shower.

Wall Jamb

Cap

Wall Jamb Cap

Wall Jamb

Cap

Sterling 15 1034028-2-H

Page is loading ...

USA: 1-800-STERLING

(1-800-783-7546)

México: 001-877-680-1310

SterlingPlumbing.com

1034028-2-H

Sterling 6506-33S Installation guide

This manual is also suitable for

Sterling 6506-33S Installation guide

in other languages

Related papers

Other documents