Generation Lighting 49031BLE-71 Installation guide

Brand
Generation Lighting
Model
49031BLE-71
Type
Installation guide

This manual is also suitable for

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-764
0
51409
Car
efully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
•
Be sure the electricity to the system you are working on is
t
urned off; either the fuse removed or the circuit breaker set
at off.
•
Use of other manufacturers components will void warranty,
l
isting and create a potential safety hazard.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• Proper wiring is essential for the safe operation of this fixture.
• Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
T
o clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
K
eep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
Insert fixture mounting screws (B) into threaded holes of universal
mounting plate (A). Run screws all the way down to the heads.
Place universal mounting plate (A) against outlet box (not supplied)
and screw in place using #8-32 outlet box screws (not supplied). Be
sure the mounting screws (B) are perfectly vertical so fixture hangs
straight.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
STEP 2:
INSTALLATION
*OUTLET BOX *#8-32
OUTLET
BOX
SCREWS
FIGURE 1 *NOT INCLUDED
DIFFUSER
MOUNTING
SCREWS (B)
GREEN
GROUNDING
SCREW (E)
*SUPPL
Y
GROUND
WIRE
CANOPY (F)
UNIVERSAL
MOUNTING
PLATE (A)
CAP NUTS (G)
*ORANGE
WIRE
CONNECTORS
SUPPORT RING (D)
RET
AINING RING (B)
Hg
MARK MEANS LAMP CONT
AINS MERCUR
Y
.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
GROUNDING INSTRUCTIONS: The green grounding screw (E) is to
be inserted into the hole with two raised dimples provided on the
universal mounting plate (A). Wrap the ground wire from the outlet box
(bare metal or green insulated wire) around the green grounding
screw (E) on the universal mounting plate (A) and tighten the green
grounding screw to secure.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
INSTALLATION (continued) HC-764
STEP 3:
A
.
U
se an orange listed wire connector to connect the 18AWG fixture
hot wire (black wire, or round and smooth tracer) to the supply hot wire.
B. Use an orange listed wire connector to connect the 18AWG
fixture common wire (white wire, or square and rigid) to the supply
c
ommon wire.
C. Gently try to remove the wires from the connector. If you can
r
emove the wires, carefully re-do the wiring connection.
STEP 4:
Make sure no bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
CLEANING
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering
parts.
ORDERING PARTS
S
TEP 1:
STEP 2:
STEP 3:
I
nstall diffuser (A) and support ring (D) if necessary, over socket and
secure with retaining ring (B).
Install self ballasted lamp (C) by gently twisting into socket.
After wires are connected, tuck them carefully inside the outlet box.
P
osition canopy (F) over mounting screws (B) and secure in place
with cap nuts (G).
FIGURE 2
ONE PIECE
LAMP/BALLAST
COMBINATION
ONE PIECE LAMP/
BALLAST
COMBINATION (C)
SOCKET
  • Page 1 1
  • Page 2 2

Generation Lighting 49031BLE-71 Installation guide

Brand
Generation Lighting
Model
49031BLE-71
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents