3M 3M-Matic™ Adjustable Case Sealer a80b-3 Operating instructions

Instructions and Parts List

a80b Type 10800

Adjustable

Case Sealer

with

AccuGlide 2+

Taping Heads

"3M-Matic"and "AccuGlide" are Trademarks of,

3M St. Paul, MN 55144-1000

Printed in U.S.A.

Serial No.

For reference, record machine serial number here.

Important Safety

Information

Spare Parts

™

3M-Matic

™

BEFORE INSTALLING

OR OPERATING THIS

EQUIPMENT

Read, understand, and

follow all safety and

operating instructions.

It is recommended you

immediately order the

spare parts listed in the

"Spare Parts/Service

Information" section.

These parts are expected

to wear through normal

use, and should be kept

on hand to minimize

production delays.

3M Industrial Adhesives and Tapes

3M Center, Building 220-5E-06

St. Paul, MN 55144-1000

This instruction manual covers safety aspects,

handling and transport, storage, unpacking,

preparation, installation, operation, adjust-

ments, maintenance, troubleshooting, repair

work and servicing plus parts list of the

3M-Matic

TM

a80b Adjustable case sealer.

3M Industrial Adhesives and Tapes

3M Center, Building 220-5E-06

St. Paul, MN 55144-1000

Edition April 2011

Copyright 3M 2011

The manufacturer reserves the right to change

the product at any time without notice.

i

To Our Customers:

This is the 3M-Matic™/AccuGlide™/Scotch

®

equipment you ordered.

It has been set up and tested in the factory with Scotch

®

tapes. If technical assistance

or replacement parts are needed, call or fax the appropriate number.

Included with each machine is an Instructions and Parts List manual.

Technical Assistance / Replacement Parts and Additional Manuals:

Call the 3M-Matic™ Help line at 1-800 328-1390. Provide the customer support coordinator with the

model/machine name, machine type, and serial number that are located on the identiﬁ cation plate

(For example: Model a80b - Type 10800 - Serial Number 13282).

Identiﬁ cation Plate

Replacement Parts and Service Information

3M-Matic

™

, AccuGlide

™

and Scotch

™

are

Trademarks of

3M St. Paul, MN 55144-1000

Printed in U.S.A.

3M Industrial Adhesives and Tapes

3M Center, Building 220-5E-06

St. Paul, MN 55144-1000

ii

For Industrial Use Only

THIS PAGE IS BLANK

TABLE OF CONTENTS - MANUAL 1: a80b Adjustable Case Sealer

(For Taping Head Information - See MANUAL 2: AccuGlide™ 2+ STD 2 Inch Taping Head)

a80b Adjustable Case Sealer Page

Cover Page

Replacement Parts and Service Information ....................................................................... i - ii

Table of Contents ................................................................................................................. iii - v

Acronyms and Abbreviations ................................................................................................ vi

1. Introduction

1.1 Manufacturing Speciﬁ cations

/ Description / Intended Use

......................................... 1

1.2 How to Read and Use the Manual / Reference Documents ......................................... 2

1.2.1 Importance of the Manual .................................................................................. 2

1.2.2 Manual Maintenance ......................................................................................... 2

1.2.3 Consulting the Manual ........................................................................................ 2

1.2.4 How to Update the Manual in Case of Modiﬁ cations ........................................... 2

2. General Information

2.1 Identiﬁ cation Data ......................................................................................................... 3

2.2 Warranty / Contents ...................................................................................................... 4

3. Safety

3.1 General Safety Information ........................................................................................... 5

3.2 Signal Words Explanation ............................................................................................. 5

3.3 Table of Warnings .......................................................................................................... 6 - 7

3.4 Operator’s Qualiﬁ cations .............................................................................................. 8

3.5 Number of Operators

.................................................................................................... 8

3.6 Safe Use of the Machine Instructions

........................................................................... 8

3.7 Residual Hazards .......................................................................................................... 8

3.8 Prevent Other Hazards - Recommendations and Measures ........................................ 8

3.9 Personal Safety Measures ........................................................................................... 8

3.10 Incorrect / Predictable Actions Not Allowed .................................................................. 8

3.11 Operator's Required Skill Levels .................................................................................. 9

3.12 Component Locations .................................................................................................. 10

3.13 Table of Warnings and Replacement Labels ................................................................ 11

4. Technical Speciﬁ cations

4.1 Power Requirements .................................................................................................... 12

4.2 Operating Rate

............................................................................................................. 12

4.3 Operating Conditions

.................................................................................................... 12

4.4 Tape .............................................................................................................................. 12

4.5 Tape Width .................................................................................................................... 12

4.6 Tape Roll Diameter ....................................................................................................... 13

4.7 Tape Application Leg Length - Standard .......................................................................13

Tape Application Leg Length - Optional

4.8 Box Board ..................................................................................................................... 13

4.9 Box Weight and Size Capacities ................................................................................... 13

4.10 Machine Dimensions ..................................................................................................... 14

4.11 Machine Noise Levels ................................................................................................... 14

4.12 Buildup Recommendations ............................................................................................ 14

iii

2011 April

a80b-NA

6

THIS PAGE IS BLANK

TABLE OF CONTENTS (continued)

5. Shipment, Handling, and Storage

5.1 Packed Machine Shipment and Handling ........................................................................... 15

5.2 Overseas Shipment Packaging (Optional) .......................................................................... 15

5.3 Handling and Transportation of Uncrated Machine ............................................................. 15

5.4 Machine Storage ................................................................................................................. 15

6. Unpacking

6.1 Uncrating and Removal of Pallet ........................................................................................ 16

6.2 Packaging Materials Disposal ............................................................................................. 16

7. Installation

7.1 Operating Conditions

.......................................................................................................... 17

7.2 Space Requirements for Machine Operation and Maintenance ......................................... 17

7.3 Tool Kit Supplied with the Machine ..................................................................................... 17

7.4 Machine Positioning ............................................................................................................ 17

7.5 Plastic Ties Removal ........................................................................................................... 18

7.6 Assembly Completion .......................................................................................................... 18

7.7 Taping Heads Completion ................................................................................................... 19

7.8 Preliminary Electric Inspection ............................................................................................ 19

7.9 Main Power Machine Connection and Inspection ............................................................... 19

7.10

Inspection of Phases .......................................................................................................... 19

8. Theory of Operation

8.1 Working Cycle Description .................................................................................................. 20

8.2 Running Mode Deﬁ nition ..................................................................................................... 20

8.3.1 Normal Stop Procedure .............................................................................................20

8.3.2 Emergency Stop ....................................................................................................... 20

9. Controls

9.1 Box Width Adjusting Knobs ................................................................................................. 21

9.2 On / Off Switch ..................................................................................................................... 21

9.3 Emergency Stop Button (Latching) ..................................................................................... 21

10. Safety devices

10.1 Blade Guards ..................................................................................................................... 22

10.2 Emergency Stop Button ..................................................................................................... 22

10.3 Electric System ................................................................................................................... 22

11. Buildup and Adjustments

11.1 Box Width Adjustment ........................................................................................................ 23

11.2 Changing the Tape Leg Length .......................................................................................... 23

11.3 Run Boxes to Check Adjustment ........................................................................................ 23

iv

a80b-NA

2011 April

THIS PAGE IS BLANK

9

12. Operation

12.1 Operator’s Correct Working Position .............................................................................. 24

12.2 Starting the Machine ....................................................................................................... 24

12.3 Starting Production ......................................................................................................... 24

12.4 Tape Replacement .......................................................................................................... 24

12.5 Box Size Adjustment ....................................................................................................... 24

12.6 Cleaning .......................................................................................................................... 24

12.7 Table of Adjustments ....................................................................................................... 24

12.8 Safety Devices Inspection ............................................................................................... 24

12.9 Troubleshooting .............................................................................................................. 25

13. Maintenance

13.1 Safety Measures (see section 3) .................................................................................... 26

13.2 Tools and Spare Parts Supplied with Machine ................................................................ 26

13.3 Maintenance Operations - Recommended Inspections and Frequency .......................... 26

13.4 Inspections to be Performed Before and After Every Maintenance Operation ................ 26

13.5 Safety Features (Inspection Efﬁ ciency) .......................................................................... 26

13.6 Machine Cleaning ........................................................................................................... 27

13.7 Cutter Blade Cleaning ..................................................................................................... 27

13.8 Lubrication ...................................................................................................................... 27

13.9 Lubrication Products ....................................................................................................... 27

13.10 Drive Belt Replacement .................................................................................................. 28

13.11 Box Drive Belt Tension and Drive Pulley Ring ................................................................ 29

13.12 Maintenance Work Log ................................................................................................... 30

14. Additional Instructions

14.1 Machine Disposal Information ......................................................................................... 31

14.2 Fire emergency ............................................................................................................... 31

15. Special Information

15.1 Statement of Conformity ................................................................................................. 31

15.2 Hazardous Substances Emission ................................................................................... 31

15.3 Safety Features List ........................................................................................................ 31

15.4 Copies of Test Reports, Certiﬁ cations (etc.)Required by User

......................................... 31

16. Technical Documentation and Information

16.1 Electric Diagrams ............................................................................................................ 33

16.2 Spare Parts / Ordering .................................................................................................... 34 - 35

Drawings and Parts Lists ....................................................................................................... 37 - End of Manual

TAPING HEAD INFORMATION -

MANUAL 2: AccuGlide™ 2+ STD 2 Inch Taping Head (See MANUAL 2 for Table of Contents)

TABLE OF CONTENTS (continued)

v

a80b-NA

2011 April

ABBREVIATIONS AND ACRONYMS

vi

LIST OF ABBREVIATIONS, ACRONYMS

3M-Matic - Trademark of 3M St. Paul, MN 55144-1000

AccuGlide - Trademark of 3M St. Paul, MN 55144-1000

Scotch - Trademark of 3M St. Paul, MN 55144-1000

Drw. - drawing

Ex. - for example

Figure - exploded view ﬁ gure no. (spare parts)

Figure - Illustration

Max. - maximum

Min. - minimum

Nr. - number

N/A - not applicable

OFF - machine not operating

ON - machine operating

PLC - Programmable Logic Control

PP - Polypropylene

PU/PU Foam - Polyurethane Foam

PTFE - Polytetraﬂ ourethelene

PVC - Poly-vinyl chloride

W - Width

H - Height

L - Length

a80b-NA

2011 April

1-INTRODUCTION

1

The 3M-Matic

TM

a80b Adjustable Case Sealer with AccuGlide

TM

2+ Taping Heads is designed

to apply a “C” clip of Scotch

®

pressure-sensitive ﬁ lm box sealing tape to the bottom center seam

of regular slotted containers. The a80b is manually adjustable for a wide range of box sizes.

See "Speciﬁ cations Section—Box Weight and Size Capacities".

3M-Matic

TM

a80b Adjustable Case Sealer, Type 10800

1.1 Manufacturing Speciﬁ cations / Description / Intended Use

a80b-NA

2011 April

2

1.2 How to Read and Use the Instruction Manual

This instruction manual covers safety aspects,

handling and transport, storage, unpacking,

preparation, installation, operation, buildup and

adjustments, technical and manufacturing speciﬁ ca-

tions, maintenance, troubleshooting, repair work and

servicing, electric diagrams, warranty information,

disposal (ELV), a deﬁ nition of symbols, plus a parts

list of the 3M-Matic

TM

a80b Adjustable case sealer

3M Industrial Adhesives and Tapes Division 3M

Center, Bldg. 220-5E-06 St. Paul, MN 55144-1000

(USA) / Edition April 2011 / Copyright 3M 2011 / All

rights reserved. The manufacturer reserves the right

to change the product at any time without notice.

Publication © 3M 2011 44-0009-2069-2.

1.2.1 Importance of the Manual

The manual is an important part of the machine; all

information contained herein is intended to enable

the equipment to be maintained in perfect condition

and operated safely. Ensure that the manual is avail-

able to all operators of this equipment and is kept

up to date with all subsequent amendments. Should

the equipment be sold or disposed of, please ensure

that the manual is passed on. Electrical and pneu-

matic diagrams are included in the manual.

Equipment using PLC controls and/or electronic

components will include relevant schematics or

programs in the enclosure and in addition, the

relevant documentation will be delivered separately.

1-INTRODUCTION (continued)

1.2.2 Manual Maintenance

Keep the manual in a clean and dry place near the

machine. Do not remove, tear, or rewrite parts of

the manual for any reason. Use the manual without

damaging it. If the manual has been lost or

damaged, ask your after-sale service for a new copy.

1.2.3 Consulting the Manual

The manual is composed of:

- Pages which identify the document and the machine

- Index of the subjects

- Instructions and notes on the machine

- Enclosures, drawings and diagrams

- Spare parts (last section)

All pages and diagrams are numbered. The spare

parts lists are identiﬁ ed by the ﬁ gure identiﬁ cation

number. All the notes on safety measures or

possible dangers are identiﬁ ed by the symbol:

1.2.4 How to Update the Manual in Case of

Modiﬁ cations to the Machine

Modiﬁ cations to the machine are subject to

manufacturer’s internal procedures. The user

receives a complete and up-to-date copy of the

manual together with the machine. Afterwards

the user may receive pages or parts of the

manual which contain amendments or

improvements made after its ﬁ rst publication.

The user must use them to update this manual.

2011 April

a80b-NA

2-GENERAL INFORMATION

3

2.1 Data Identifying Manufacturer and Machine

2011 April

a80b-NA

For Industrial Use Only

4

2-GENERAL INFORMATION (continued)

2011 April

a80b-NA

Contents – a80b Adjustable Case Sealer

(1) a80b Adjustable Case Sealer, Type 10800

(1) Side Belt Assembly Width Adjustment Crank/Hardware

(1) Tool/Spare Parts Kit

(1) Instruction and Parts Manual

2.2 Warranty

Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR

PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR

USAGE OF TRADE:

3M sells its 3M-Matic

™

a80b Adjustable Case Sealer, Type 10800 with the following warranties:

1. The drive belts and the taping head knives, springs and rollers will be free from all defects for

ninety (90) days after delivery.

2. All other taping head parts will be free from all defects for three (3) years after delivery.

3. All other parts will be free from all defects for two (2) years after delivery.

If any part is proved to be defective within its warranty period, then the exclusive remedy and 3M’s and seller’s

sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned

immediately to 3M’s factory or an authorized service station designated by 3M. A part will be presumed to have

become defective after its warranty period unless the part is received or 3M is notiﬁ ed of the problem no later than

ﬁ ve (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable

time, then 3M at its option, will replace the equipment or refund the purchase price. 3M shall have no obligation

to provide or pay for the labor required to install the repaired or replacement part. 3M shall have no obligation

to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any accidental cause

other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning, improper operating

environment, improper utilities or operator error.

Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential

damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.

The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a

written agreement signed by authorized ofﬁ cers of 3M and seller.

5

3.1 General Safety Information

Read all the instructions carefully before starting

work with the machine; please pay particular

attention to sections marked by the symbol:

The machine is provided with a LATCHING

EMERGENCY STOP BUTTON (Figure 3-1);

when this button is pressed, it stops the machine

at any point in the working cycle. Maintain clear

access to power cord while machine is operating.

Disconnect plug from power source before machine

maintenance (Figure 3-1). Also disconnect air if the

machine has a pneumatic system. Keep this manual

in a handy place near the machine. This manual

contains information that will help you to maintain

the machine in a good and safe working condition.

3-SAFETY

3.2 Explanation of Signal Word and

Possible Consequences

Indicates a potentially hazardous

situation, which, if not avoided,

may result in minor or moderate

injury and/or property damage.

CAUTION:

Indicates a potentially hazardous

situation, which, if not avoided,

could result in death or serious

injury and/or property damage.

WARNING:

2011 April

a80b-NA

This safety alert symbol identiﬁ es

important messages in this manual.

READ AND UNDERSTAND THEM

BEFORE INSTALLING OR

OPERATING THIS EQUIPMENT.

Figure 3-1

6

3.3 Table of Warnings

• To reduce the risk associated with

mechanical and electrical hazards:

 Read, understand, and follow all safety and

operating instructions before operating or

servicing the case sealer.

 Allow only properly trained and qualiﬁ ed

personnel to operate and service this

equipment.

• To reduce the risk associated with

pinches, entanglement and hazardous

voltage:

 Turn electrical supply off and disconnect

before performing any adjustments,

maintenance or servicing the machine or

taping heads.

• To reduce the risk associated with

pinches and entanglement hazards:

 Do not leave the machine running while

unattended.

 Turn the machine off when not in use.

 Never attempt to work on any part of the

machine, load tape, or remove jammed

boxes from the machine while the machine

is running.

• To reduce the risk associated with

hazardous voltage:

 Position electrical cord away from foot and

vehicle trafﬁ c.

Figure 3-4

Figure 3-3

Figure 3-2

WARNING

3-SAFETY (continued)

2011 April

a80b-NA

7

• To reduce the risk associated with

pinch hazards:

 Keep hands clear of the upper head support

assembly as boxes are transported through

the machine.

 Keep hands, hair, loose clothing, and jewelry

away from box compression rollers.

 Always feed boxes into the machine by

pushing only from the end of the box.

 Keep hands, hair, loose clothing, and jewelry

away from moving belts and taping heads.

CAUTION

• To reduce the risk associated with sharp

blade hazards:

− Keep hands and ﬁ ngers away from tape

cutoff blades under orange blade guards.

The blades are extremely sharp.

WARNING

• To reduce the risk associated with ﬁ re

and explosion hazards:

− Do not operate this equipment in potentially

ﬂ ammable/explosive environments.

• To reduce the risk associated with

muscle strain:

− Use the appropriate rigging and material

handling equipment when lifting or

repositioning this equipment.

− Use proper body mechanics when

removing or installing taping heads that are

moderately heavy or may be considered

awkward to lift.

WARNING

Sharp Knife

Figure 3-7

Figure 3-5

Figure 3-6

- Important : Never remove the safety device

which covers the blade on the taping unit.

Any error may cause serious injuries

(Figure 3-5).

3-SAFETY (continued)

2011 April

a80b-NA

8

3-SAFETY (continued)

3.7 Residual Hazards

The case sealer has been designed and incorpo-

rates various safety protections which should never

be removed or disabled. Notwithstanding the safety

precautions conceived by the designers of the

machine, it is essential that the operator and service

personnel be warned that the residual hazards exist

which cannot be eliminated.

2011 April

a80b-NA

3.8 Recommendations and Measures to Prevent

Other Hazards which Cannot be Eliminated

- The operator must stay on the working position

shown in the Operation Section (Figure 12-1).

- The operator must never touch the running driving

belts or put his hands inside any cavity.

- The operator must pay attention to the blades

during the tape replacement.

3.4 Operator's Qualiﬁ cations

- Machine Operator

- Mechanical Maintenance Technician

- Electrical Maintenance Technician

- Manufacturer’s Technician/Specialist

3.5 Number of Operators

The operations described below have been analyzed

by the manufacturer; the recommended number of

operators for each operation provides the best and

safest work performance.

Note: A smaller or greater number of operators

could be unsafe.

3.6 Instructions for a Safe Use of the Machine /

Deﬁ nition of Operator's Qualiﬁ cations

Only persons who have the skills described in the

skill levels section should be allowed to work on the

machine. It is the responsibility of the user to appoint

the operators having the appropriate skill level and

the appropriate training for each category of job.

• To reduce the risk associated with

mechanical and electrical hazards:

 Read, understand, and follow all safety and

operating instructions before operating or

servicing the case sealer.

 Allow only properly trained and qualiﬁ ed

personnel to operate and service this

equipment.

WARNING

3.9 Personal Safety Measures

Safety glasses, safety gloves, safety helmet, safety

shoes, air ﬁ lters, ear muffs - None is required except

when recommended by the user.

3.10 Predictable Actions which are Incorrect and

Not Allowed

- Never try to stop/hold the box while being driven

by the the belts.

Only use the EMERGENCY STOP BUTTON.

- Never work without the safety protections.

- Never remove or disable the safety devices.

- Only authorized personnel should be allowed

to carry out the adjustments, repairs or main-

tenance which require operation with reduced

safety protections. During such operations,

access to the machine must be restricted.

When the work is ﬁ nished, the safety

protections must immediately be reactivated.

- The cleaning and maintenance operations must be

performed after disconnecting the electric power.

- Do not modify the machine or any part of it.

The manufacturer will not be responsible

for any modiﬁ cations.

- Clean the machine using only dry cloths or

light detergents. Do not use solvents, petrols, etc.

- Install the machine following the suggested layouts

and drawings. The manufacturer will not be respon-

sible for damages caused by improper installation.

9

3-SAFETY (continued)

2011 April

a80b-NA

Operator's Skill Levels Required to Perform the Main Operations on Machine

Skill 1:

Machine Operator

This operator is trained to use the machine with the

machine controls, to feed cases into the machine,

make adjustments for different case sizes, to change

the tape and to start, stop and restart production.

Skill 2: Mechanical Maintenance Technician

This operator is trained to use the machine as the

MACHINE OPERATOR and in addition is able to:

• Work with the safety protection disconnected

• Check and adjust mechanical parts

• Carry out machine maintenance operations/repairs

He is not allowed to work on live electrical components

Skill 2a: Electrical Maintenance Technician

This operator is trained to use the machine as the

MACHINE OPERATOR and in addition is able to:

• Work with the safety protection disconnected

• Check and adjust mechanical parts

• Carry out machine maintenance operations /

repairs / adjustments / repair electrical components

He is allowed to work on live electrical panels,

connector blocks, control equipment, etc.

Skill 3: Specialist from the Manufacturer

Skilled operator sent by the manufacturer or its

agent to perform complex repairs or modiﬁ cations

(on agreement with the customer).

3.11 Operator's Skill Levels Required to Perform

the Main Operations on the Machine

The Table shows the minimum operator's skill for

each machine operation.

Important: The factory manager must ensure that

the operator has been properly trained on all the

machine functions before starting work.

Operation Machine Status

Required

Operator

Skill

Number of

Operators

Machine installation and setup Running with safety

protections disabled

2 and 2a 2

Adjusting box size

Stopped by pressing the

EMERGENCY STOP

button

11

Tape replacement

Stopped by pressing the

EMERGENCY STOP

button

11

Blade replacement Electric power

disconnected

21

Drive belt replacement Electric power

disconnected

21

Ordinary maintenance Electric power

disconnected

21

Extraordinary mechanical

maintenance

Running with safety

protections disabled

31

Extraordinary electrical

maintenance

Running with safety

protections disabled

2a 1

• To reduce the risk associated with

mechanical and electrical hazards:

 Allow only properly trained and qualiﬁ ed

personnel to operate and service this machine

WARNING

10

3-SAFETY (continued)

2011 April

Refer to Figure 3-8 below to acquaint yourself with the various components and controls of the case sealer.

Also refer to Manual 2 for taping head components.

Figure 3-8—a80b Case Sealer Components (Left Front View)

a80b-NA

3.12 Component Locations

Belt Guard

Adjustable

Side Guides

with Box

Drive Belts

Lower

Taping Head

Power Switch

Assembly

Drive Belt

Adjustment

Handle

Emergency

Stop

Switch

Machine

Bed

Page is loading ...

3M 3M-Matic™ Adjustable Case Sealer a80b-3 Operating instructions

This manual is also suitable for

3M 3M-Matic™ Adjustable Case Sealer a80b-3 Operating instructions

Related papers

Other documents