ADLINK Technology cPCI-3620 User manual

Advance Technologies; Automate the World.

Manual Rev.: 1.00

Revision Date: February 16, 2016

Part No: 50-15098-2000

cPCI-3620 Series

Low-Power 3U CompactPCI

®

Quad-Core Intel

®

Atom™ Processor Blade

User’s Manual

ii Revision History

Revision History

Revision Release Date Description of Change(s)

1.00 16/02/2016 Initial release

Preface iii

cPCI-3620

Preface

This document contains proprietary information protected by copy-

right. All rights are reserved. No part of this manual may be repro-

duced by any mechanical, electronic, or other means in any form

without prior written permission of the manufacturer.

Disclaimer

The information in this document is subject to change without prior

notice in order to improve reliability, design, and function and does

not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, spe-

cial, incidental, or consequential damages arising out of the use or

inability to use the product or documentation, even if advised of

the possibility of such damages.

Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global

environmental preservation through compliance with the Euro-

pean Union's Restriction of Hazardous Substances (RoHS) direc-

tive and Waste Electrical and Electronic Equipment (WEEE)

directive. Environmental protection is a top priority for ADLINK.

We have enforced measures to ensure that our products, manu-

facturing processes, components, and raw materials have as little

impact on the environment as possible. When products are at their

end of life, our customers are encouraged to dispose of them in

accordance with the product disposal and/or recovery programs

prescribed by their nation or company.

Trademarks

Product names mentioned herein are used for identification pur-

poses only and may be trademarks and/or registered trademarks

of their respective companies.

iv Preface

Conventions

Take note of the following conventions used throughout this

manual to make sure that users perform certain tasks and

instructions properly.

NOTE:

Additional information, aids, and tips that help users perform

tasks.

CAUTION:

Information to prevent minor physical injury, component dam-

age, data loss, and/or program corruption when trying to com-

plete a task.

WARNING:

Information to prevent serious physical injury, component

damage, data loss, and/or program corruption when trying to

complete a specific task.

Table of Contents v

cPCI-3620

Table of Contents

Revision History...................................................................... ii

Preface .................................................................................... iii

List of Figures ........................................................................ ix

List of Tables.......................................................................... xi

1 Introduction ........................................................................ 1

1.1 Overview.............................................................................. 1

1.2 Features............................................................................... 2

1.3 Model Number Decoder....................................................... 3

1.4 Package Contents ............................................................... 5

2 Specifications..................................................................... 7

2.1 cPCI-3620 Processor Blade Specifications......................... 7

2.2 cPCI-R3610(T) RTM Specifications..................................... 9

2.3 Block Diagrams.................................................................. 10

2.4 I/O Connectivity Table ....................................................... 13

2.5 Power Requirements......................................................... 14

3 Functional Description .................................................... 17

3.1 Processors......................................................................... 17

3.2 PMC/XMC.......................................................................... 19

3.3 Intel® Virtualization Technology........................................ 19

3.4 Intel® AES New Instructions.............................................. 19

3.5 Battery ............................................................................... 20

4 Board Interfaces............................................................... 21

4.1 cPCI-3620 Series Board Layout........................................ 21

4.2 cPCI-3620 Blade Assembly Layout ................................... 22

vi Table of Contents

4.3 cPCI-3620D Blade Assembly Layout................................. 23

4.4 cPCI-3620T Blade Assembly Layout................................. 24

4.5 cPCI-3620N Blade Assembly Layout................................. 25

4.6 cPCI-3620 Series Faceplate.............................................. 26

4.7 cPCI-R3610(T) RTM Board Layout.................................... 29

4.8 cPCI-R3610(T) RTM Faceplate......................................... 30

4.9 Connector Pin Assignments............................................... 31

4.10 Jumper Settings................................................................. 47

5 Getting Started .................................................................. 49

5.1 CPU and Heatsink ............................................................. 49

5.2 SATA Drive Installation...................................................... 50

5.3 PMC/XMC Card Installation............................................... 52

5.4 Installing the cPCI-3620 to the Chassis............................. 53

5.5 RTM Installation - cPCI-R3610(T)...................................... 54

6 Driver Installation.............................................................. 55

6.1 cPCI-3620 Drivers.............................................................. 55

7 Utilities ............................................................................... 57

7.1 SEMA................................................................................. 57

7.2 Preboot Execution Environment (PXE).............................. 57

7.3 Watchdog Timer................................................................. 58

8 BIOS Setup Utility ............................................................. 59

8.1 Starting the BIOS............................................................... 59

8.2 Main Setup......................................................................... 62

8.3 Advanced BIOS Setup....................................................... 65

8.3.1 Super IO Configuration..................................................66

8.3.2 Serial Port Console Redirection.....................................67

8.3.3 CPU Configuration.........................................................70

8.3.4 PPM Configuration.........................................................72

8.3.5 Thermal Configuration...................................................73

8.3.6 IDE Configuration ..........................................................74

Table of Contents vii

cPCI-3620

8.3.7 Network Stack Configuration.........................................75

8.3.8 CSM Configuration ........................................................76

8.3.9 USB Configuration.........................................................77

8.4 Chipset Configuration ........................................................ 78

8.4.1 North Bridge...................................................................78

8.4.2 South Bridge..................................................................80

8.5 Security.............................................................................. 82

8.6 Boot Settings ..................................................................... 83

8.7 Save & Exit Menu.............................................................. 84

Important Safety Instructions .............................................. 87

Getting Service...................................................................... 89

viii Table of Contents

This page intentionally left blank.

List of Figures ix

cPCI-3620

List of Figures

Figure 2-1: cPCI-3620 Blade Functional Block Diagram..................10

Figure 2-2: cPCI-3620D Daughter Board Functional Block Diagram11

Figure 2-3: cPCI-3620T Daughter Board Functional Block Diagram11

Figure 2-4: cPCI-R3610 RTM Functional Block Diagram ................12

Figure 4-1: cPCI-3620 Series Board Layout....................................21

Figure 4-2: cPCI-3620 Blade Assembly Layout...............................22

Figure 4-3: cPCI-3620D Blade Assembly Layout.............................23

Figure 4-4: cPCI-3620T Blade Assembly Layout.............................24

Figure 4-5: cPCI-3620N Blade Assembly Layout.............................25

Figure 4-6: cPCI-3620, cPCI-3620D/N Faceplate Layout................26

Figure 4-7: cPCI-3620T/S Faceplate Layout....................................27

Figure 4-8: cPCI-R3610(T) RTM Board Layout ...............................29

Figure 4-9: cPCI-R3610(T) RTM Faceplate.....................................30

xList of Figures

This page intentionally left blank.

List of Tables xi

cPCI-3620

List of Tables

Table 2-1: cPCI-3620 Processor Blade Specifications.....................7

Table 2-2: cPCI-R3610(T) RTM Specifications.................................9

Table 2-3: cPCI-3620 I/O Connectivity ...........................................13

Table 4-1: cPCI-3620 Faceplate System LED Descriptions...........28

Table 4-2: USB 2.0 Pin Definition...................................................31

Table 4-3: VGA Pin Definition.........................................................32

Table 4-4: PS/2 Keyboard/Mouse Pin Definition.............................32

Table 4-5: RJ-45 GbE Pin Definitions.............................................33

Table 4-6: LAN Status LED Definitions...........................................33

Table 4-7: RJ-45 GbE Pin Definitions.............................................34

Table 4-8: cPCI-3620D/T COM1 (DB-9) Pin Definition...................34

Table 4-9: cPCI-3620D COM1 Mode Selection Switch Settings ....35

Table 4-10: Serial ATA Connector on DB-3610L2 Pin Definition......37

Table 4-11: PMC Connector Pin Definitions.....................................38

Table 4-12: XMC Connector Pin Definition.......................................40

Table 4-13: CompactPCI J1 Connector Pin Definition......................41

Table 4-14: CompactPCI J2 Connector Pin Definition......................42

Table 4-15: cPCI-R3610(T) Serial Port Pin Header Definition..........43

Table 4-16: cPCI-R3610(T) COM2/3 (DB-9) Pin Definition ..............43

Table 4-17: COM2 Mode Selection Switch Settings.........................44

Table 4-18: COM3 Mode Selection Switch Settings.........................45

Table 4-19: Serial ATA Connector on RTM......................................46

Table 4-20: XMC VPWR Select Jumper Settings.............................47

Table 4-21: PMC V(I/O) Select Jumper Settings..............................47

xii List of Tables

This page intentionally left blank.

Introduction 1

cPCI-3620

1 Introduction

1.1 Overview

The ADLINK cPCI-3620 Series is a 3U CompactPCI

®

processor

blade featuring a quad-core Intel

®

Atom SoC and 4GB of soldered

DDR3L-1333 ECC.

Available in single-slot (4HP) or dual-slot (8HP) width form factors,

the cPCI-3620 Series utilizes various daughter boards to provide a

broad range of I/O functionality. Faceplate I/O on the single-slot

(4HP) version includes 1x USB 3.0, 2x RJ-45 GbE and 1x VGA

port (common to all versions). Faceplate I/O on the dual-slot (8HP)

version includes additional 2x USB 2.0, 1x COM, 1x PS/2 KB/MS

and Line-in/Line-out on the cPCI-3620D or additional 2x GbE via

MIL-STD M12 connectors and 1x COM on the cPCI-3620T.

Another dual-slot option is the cPCI-3620S with an additional XMC

site on layer 2. There is also a single-slot option that provides LED

indicators only with no I/O on the faceplate (cPCI-3620N).

Graphics support is integrated on the SoC. Storage options

include an onboard 32GB SSD (optional) and 2.5" SATA drive on

layer 2 riser card (cPCI-3620D/T). One optional PCI 32-bit/66 MHz

PCIe x1 XMC site is available on the dual-slot cPCI-3620S ver-

sion.

Rear I/O signals to J2 include 2x GbE, 1x VGA, 1x USB 2.0, 2x

COM, 1x SATA 3 Gb/s, providing for expansion with an optional

Rear Transition Module (RTM).

The cPCI-3620 is an ideal solution for transportation, military, fac-

tory automation and other industrial applications that require opti-

mal computing performance for data transfer with lower power

consumption. The ADLINK cPCI-3620 provides high manageabil-

ity, supports Satellite mode operation as a standalone blade in

peripheral slots, and features ADLINK's Smart Embedded Man-

agement Agent (SEMA) for system health monitoring.

2Introduction

1.2 Features

X 3U CompactPCI blade in 4HP or 8HP width form factor

X Intel

®

Atom™ Processor E3845 SoC (4 cores, 2M L3 cache,

1.9 GHz)

X Graphics and memory controllers integrated in SoC

X Compatible with PICMG 2.0 CompactPCI R3.0 and PICMG 2.1

Hot Swap R2.0

X 4GB single channel DDR3L-1333 soldered ECC SDRAM

X 32-bit, 33/66MHz CompactPCI interface, universal V(I/O)

X Supports Satellite mode operation as a standalone blade in

peripheral slots

X Optional 32-bit, 66MHz PCIe x1 XMC site

X Supports SEMA for system health monitoring

X VGA port on faceplate switchable to rear I/O by BIOS setting

X 2x GbE ports on faceplate switchable to rear I/O by BIOS set-

ting

X Additional 2x GbE via MIL-STD M12 connectors on 8HP model

(cPCI-3620T)

X 2x USB 2.0, 1x COM and 1x PS/2 KB/MS on faceplate

X Line-in and Line-out on faceplate (cPCI-3620D)

X Optional onboard 32GB SATA SSD or mSATA socket on

daughter board (mSATA by request only)

X 2.5” SATA 3 Gb/s direct connector on 8HP version

(cPCI-3620D/T)

Introduction 3

cPCI-3620

1.3 Model Number Decoder

Blades

(A) Configuration Code

Z Blank = Single-slot width, 1x VGA, 1x USB 3.0, 2x GbE

Z D = Dual-slot width, 1x VGA, 1x USB 3.0, 2x GbE on layer

1; 2x USB 2.0, 1x COM (RS-232/422/485), 1x PS/2 KB/MS,

Line-in, Line-out and 2.5" SATA drive space on layer 2

DB-3610L2

Z T = Dual-slot width, 1x VGA, 1x USB 3.0, 2x GbE on layer

1; 2x GbE via MIL-STD M12 connectors, 1x COM

(RS-232/422/485), and 1x 2.5" SATA drive space on layer 2

DB-3620L2

Z S = Dual-slot width, 1x VGA, 1x USB 3.0, 2x GbE on

layer 1; XMC site on layer 2 DB-3UMC.

Z N = Single-slot width, no I/O ports on layer 1.

(B) CPU Code

Z E3845 = Quad-core Intel

®

Atom™ Processor E3845 SoC

(C) Memory Size Code

Z M4G = 1x 4GB DDR3L-1333 soldered ECC SDRAM

(D) Storage*

Z Blank = default with no onboard storage

Z S32 = soldered onboard 32GB SSD on daughter board

Z MS = mSATA socket on daughter board (by request)

*For more options, contact your ADLINK representative.

cPCI-3620D / E3845 / M4G / S32

(A) (B) (C) (D)

4Introduction

RTMs

(A) Model Code

Z Blank = Dual-slot width, 50mm depth 3U RTM with 2x

COM, 1x USB 2.0, 1x SATA 3Gb/s, 1x VGA, 2x GbE

Z T = Dual-slot width, 80mm depth 3U RTM with 2 x COM, 1x

USB 2.0, 1x SATA 3Gb/s, 1x VGA, 2x GbE

NOTE:

2x GbE, 1x VGA and 1x SATA signals on RTM are switched

from faceplate of blade.

cPCI- R3610T

(A)

Introduction 5

cPCI-3620

1.4 Package Contents

The cPCI-3620 is packaged with the following components. If any

of the following items are missing or damaged, retain the shipping

carton and packing material and contact the dealer for inspection.

Please obtain authorization before returning any product to

ADLINK. The packing contents of cPCI-3620 Series non-standard

configurations will vary depending on customer requests.

Processor Blade

X The cPCI-3620 Series Processor Blade

Z CPU and memory specifications will differ depending on

options selected

Z Thermal module is assembled on the board

X Y-cable for PS/2 combo port (8HP version only)

X 2.5" SATA drive accessory pack (8HP version only)

Rear Transition Module

X cPCI-R3610: 8HP width, 50mm depth Rear Transition Mod-

ule with 2x COM, 1x USB 2.0, 2x GbE, 1x SATA, 1x VGA

X cPCI-R3610T: 8HP width, 80mm depth Rear Transition

Module with 2x COM, 1x USB 2.0, 2x GbE, 1x SATA, 1x

VGA

NOTE:

The contents of non-standard cPCI-3620 configurations may

vary depending on the customer’s requirements.

CAUTION:

This product must be protected from static discharge and phys-

ical shock. Never remove any of the components except at a

static-free workstation. Use the anti-static bag shipped with the

product when putting the board on a surface. Wear an

anti-static wrist strap properly grounded on one of the system's

ESD ground jacks when installing or servicing system compo-

nents.

6Introduction

This page intentionally left blank.

Specifications 7

cPCI-3620

2 Specifications

2.1 cPCI-3620 Processor Blade Specifications

CompactPCI

®

Standards

•PICMG

®

2.0 CompactPCI

®

Rev. 3.0

•PICMG

®

2.1 Hot Swap Specification Rev. 2.0

Mechanical • Standard 3U CompactPCI

®

• Board size: 100mm x 160mm

• Single slot (4HP, 20.32mm); Dual slot (8HP, 40.64mm)

Processor • Intel

®

Atom™ Processor E3845, quad-core, 1.91 GHz, 2MB

cache, TDP 10W

• Passive heatsink

Memory • 4GB single channel DDR3L-1333 ECC soldered memory

CompactPCI

Bus

• PCI 32-bit, 33/66MHz; 3.3V, 5V universal V I/O

• Supports operation in system slot as master or in peripheral slot

as standalone blade without connectivity to CompactPCI bus

(Satellite mode)

Gigabit

Ethernet

• Two PCIe x1 Intel

®

I210 Gigabit Ethernet controllers

(2 additional GbE by M12 connectors optional)

• Two egress 10/100/1000BASE-T ports on faceplate

• Two egress 10/100/1000BASE-T ports routed to rear transition

module (switched from faceplate)

Graphics • Integrated on Intel

®

Atom™ processor

• VGA on faceplate switchable to J2 (RTM) by BIOS setting

• Analog support up to QXGA 2560x1600 @60Hz, 32-bit

• Single display

USB • Up to three USB faceplate ports (cPCI-3620D)

Serial Ports • One RS-232/422/485 serial port on faceplate

• cPCI-3620D supports RS-485+

• cPCI-3620T supports RS-485 with flow control

PMC/XMC • One 32-bit/66MHz PMC site or PCIe x1 XMC site (cPCI-3620S)

Audio • Line-in/Line-out on faceplate by Realtek ALC262 High Definition

Audio codec (cPCI-3620D only)

Storage

Interfaces

1

• Optional onboard 32GB SSD or mSATA socket on daughter

board (mSATA by request)

• One SATA 3Gb/s direct connector for 2.5" drive (8HP version)

BIOS • AMI EFI BIOS, 64Mbit SPI flash memory

Table 2-1: cPCI-3620 Processor Blade Specifications

8 Specifications

Faceplate I/O 4HP (cPCI-3620)

• 1x USB 3.0 port

• 2x 10/100/1000BASE-T Ethernet ports

• 1x VGA port

4HP (cPCI-3620N)

• LEDs only (Power, HDD, WDT, GP, GbE), no I/O

8HP (cPCI-3620D)

• 1x USB 3.0 ports

• 2x 10/100/1000BASE-T Ethernet ports

• 1x VGA port

• 2x USB 2.0 ports

• DB-9 RS-232/422/485 port

• PS/2 Keyboard/Mouse combo port

• Line-in and Line-out port

8HP (cPCI-3620T)

• 1x USB 3.0 ports

• 2x 10/100/1000BASE-T Ethernet ports

• 1x VGA port

• 2x GbE via MIL-STD M12 ports

• DB-9 RJ-45 RS-232/422/485 port

8HP (cPCI-3620S)

• 1x USB 3.0 ports

• 2x 10/100/1000BASE-T Ethernet ports

• 1x VGA port

• PMC/XMC site

OS

Compatibility

• Microsoft Windows 7 32/64-bit

• Microsoft Windows 8 32/64-bit

• Red Hat Enterprise Linux 6.5, 64-bit

• Fedora 20, 64-bit

• VxWorks 6.1 (5.5 by request)

• Other OS support by request

Environmental • Operating Temperature

1

:

Standard: -40°C to 70°C (fanless)

Extreme: -40°C to +85°C (forced air flow)

• Storage Temperature: -50°C to 100°C

• Humidity: 95% @60°C non-condensing

• Shock: 20G peak-to-peak, 11ms duration, non-operating

•Vibration

2

: 2Grms, 5-500Hz, each axis, operating (w/o hard

drive)

EMI • EN55022

• EN50155

• FCC Class A

Table 2-1: cPCI-3620 Processor Blade Specifications

Page is loading ...

ADLINK Technology cPCI-3620 User manual

This manual is also suitable for

ADLINK Technology cPCI-3620 User manual

Related papers

Other documents